11-190 Paper Remains On V-Tra In Sensor Rap; 11-191 Paper Remains At Mail Box Vertical Sensor / 1 Bin Sensor Rap - Xerox DocuColor 12/DCCS50 Service Manual

11-190 Paper Remains on V-Tra In Sensor RAP

The Control Logic detected that paper remained on the V-Tra In Sensor at power on.
NOTE: If this machine has a Finisher/Sorter Accessory, go to Section 8D,
Remains on V-Tra In Sensor RAP to troubleshoot this Fault Code.
NOTE: Ensure that Sorter S-1 Tag is installed.
Initial Actions
• Refer to BSD11.4 and BSD 11.8 for the following procedure.
• Ensure that no paper is blocking the V-Tra In sensor and the sensor actuator moves freely.
• Check for any obstructions in the paper path.
• Ensure that P/J562 on the Mail Box Control PWB, and
are connected before beginning this RAP.
Procedure
Enter dC330 011-142 Vertical Transport In Sensor. Press Start. The display is L.
Y N
Flag 1 on BSD 11.4 and check the harness for a short circuit. If the harness is good,
Go to
replace the V-Tra In Sensor (PL 13.9).If the problem continues, replace the Mail Box Con-
trol PWB (PL 13.10).
More than +4.3 VDC is measured between P/J562-8 and GND on the Mail Box Control
PWB.
Y N
Replace the V-Tra In Sensor (PL 13.9).
Check the V-Tra In Sensor for intermittent operation. If the sensor is good, Replace the Mail
Box Control PWB (PL 13.10).
Status Indicator RAPs
11-190 Paper Remains on V-Tra In Sensor RAP, 11-
11-191 Paper Remains at Mail Box Vertical Sensor / 1 Bin
Sensor RAP
The Control Logic detected that paper remained on the Mail Box Vertical Sensor at power on.
11-190 Paper
NOTE: If this machine has a Finisher/Sorter Accessory, go to Section 8D,
Remains at Mailbox Vertical Sensor / 1 Bin Sensor RAP
NOTE: Ensure that Sorter S-1 Tag is installed.
Initial Actions
•
•
P/J567 on the V-Tra In Sensor
•
•
Procedure
Enter dC330 011-115 Mailbox Vertical Sensor. Press Start. The display is L.
Y
Less than +0.5 VDC is measured between P/J551-4 and GND on the Mail Box Control
PWB.
Y
Check the Mail Box Vertical Sensor for intermittent operation. If the sensor is good, Replace
the Mail Box Control PWB
1/05
2-200
manuals4you.com manuals4you.com
Refer to BSD11.5 for the following procedure.
Ensure that no paper or foreign object is blocking the Mail Box Vertical sensor.
Ensure that the Mail Box Vertical sensor and the Vertical LED are clean.
Ensure that P/J551 on the Mail Box Control PWB, and
Box Vertical Sensor are connected before beginning this RAP.
N
+5 VDC is measured between P/J551-3 and P/J551-5 on the Mail Box Control PWB
Y N
CR1 on the Mail Box Control PWB is on.
Y N
Go to the +5 VDC wirenet and troubleshoot the wires between P/J569-1 and
P/J44-6 on the Distribution PWB.
Replace the Mail Box Control PWB
Go to Flag 1, Flag 2, and Flag 3 on BSD 11.5 and check the harness for an open circuit. If
the harness is good, replace the Mail Box Vertical Sensor
ues, replace the Mail Box Control PWB (PL
N
Replace the Mail Box Vertical Sensor (PL
(PL 13.10).
11-191 Paper
to troubleshoot this Fault Code.
P/J818 and P/J819 on the Mail
(PL 13.10).
(PL 13.9). If the problem contin-
13.10).
13.9).
DocuColor 12/DCCS50
Reissue