Dc131Sys Nvm List (759) - Xerox DocuColor 12/DCCS50 Service Manual

dC131SYS NVM List (759)

Table 1 SYS NVM List (759)
Chain-
Link Name Default Range
759-005 FORCED FACE UP EXIT 0
759-006 REPEAT MARGIN 0
759-011 APS PRIORITY 0
759-014 NVM VERSION (for EP) -
759-018 A-I/F SET 0
759-021 DADF MODE MAG100 1
ADJ
759-023 GRADATION ADJ RST 1
SEL
759-024 NO PAPER RUN SEL 0
759-042 Product Code Switch 0
759-051 ESS PORT PRIORITY 0
759-052 Job Acceptance Prohibi- 30
tion Timer
759-053 Print ESS INFO 0
General Procedures
dC131SYS NVM List (759)
Description
0-1 0= Invert ejection
1= Straight ejection
0-1 0= Repeat margin= 3mm
1= Repeat margin= 0mm
0-1 The meaning differs depending on
the Market data in SYS NVM num-
ber 752-001.
(FX/AP, RX) 0= AB 1= Inch
(NASG) 0= Inch 1= AB
- (TBD)
0-1 0= No A-I/F KIT, 1= with A-I/F KIT
(MN unique FX/FXAP is not used.)
0-1 0= Equal magnification - Fine adjust
1= Equal magnification - No fine
adjustment
0-2 0= No Tools setup/No MAX-
SETUP
1= Tools reset/No MAXSETUP
2= Tools reset/MAXSETUP
reset
0-2 0= No Paper Run - Not
selected
1= Stop at page count limit
2= Infinite Copy
0-1 0 = 4 digit Product Code
1 = 8 digit Product Code
0-1 0= 1st I/F Port connection -
ESS priority
1= 2nd I/F Port connection -
ESS priority
1-255 (Unit= Second) Max= 4 minutes 15
seconds
0-2 Valid if Machine Config is P, P(with
UI), CP, or CPS, and sets the Print
ESS connection status.
0= 1st I/F Port connection
1= 2nd I/F Port connection
2= 1st, 2nd I/F Port connection
manuals4you.com manuals4you.com
Table 1 SYS NVM List (759)
Chain-
Link Name
759-054 Scan ESS INFO
759-073 Accessory Kit Control 1
759-074 Accessory Kit Control 2
759-075 Billing Counter Display
759-113 SET Major Version
759-114 SET Minor Version
759-115 SET Revision
759-116 SET Patch
759-117 IOSS Major Version
759-118 IOSS Minor Version
759-119 IOSS Revision
759-120 IOSS Patch
759-121 UI-P Major Version
759-122 UI-P Minor Version
759-123 UI-P Revision
759-124 UI-P Patch
759-125 UI-F Major Version
759-126 UI-F Minor Version
759-127 UI-F Revision
1/05
6-82
Default Range Description
0 0-5 Valid if Machine Config is CPS, and
sets the Print ESS connection sta-
tus.
0= 1st I/F Port connection
1= 2nd I/F Port connection
2= 1st, 2nd I/F Port connection
3= 1st I/F Port connection
(+Scan to File Job)
4= 2nd I/F Port connection
(+Scan to File Job)
5= 1st, 2nd I/F Port connection
(+Scan to File Job)
0 0-1 Sets the Print Job accessory (1st
DDI Port).
0= With Card, No Job permis-
sion without job count card
1= With Card, No Job permis-
sion without job count card
0 0-1 Sets the Print Job accessory (2nd
DDI Port).
0= With Card, No Job permis-
sion without job count card
1= With Card, No Job permis-
sion without job count card
0 0-1 0= Not displayed, 1= Displayed
- - SW Set Version 1 (0-99)
- - SW Set Version 2 (0-99)
- - SW Set Version 3 (0-9)
- 0-9 SW Set Version 4
a-z
- - IOSS SW Version1 (0-99)
- - IOSS SW Version2 (0-99)
- - IOSS SW Version3 (0-9)
- 0-9 IOSS SW Version
a-z
- - UI Program SW Version1 (0-99)
- - UI Program SW Version2 (0-99)
- - UI Program SW Version3 (0-9)
- 0-9 UI Program SW Version4
a-z
- - UI Frame SW Version1 (0-99)
- - UI Frame SW Version2 (0-99)
- - UI Frame SW Version3 (0-9)
DocuColor 12/DCCS50
Reissue