Xerox DocuColor 12/DCCS50 Service Manual page 728

Table 1 PH NVM List (761)
Chain-
Link Name Default
761-015 ADJUST TRAY 1 24
PRE FEED STOP
POSITION(TAKE
AWAY ROLL 1
SPEED 220mm/s)
761-016 ADJUST TRAY 2 20
PRE FEED STOP
POSITION(FEED
ROLL 2 SPEED
300mm/s)
761-017 ADJUST TRAY 2 10
PRE FEED STOP
POSITION(TAKE
AWAY ROLL 2
SPEED 450mm/s)
761-018 ADJUST TRAY 3 20
PRE FEED STOP
POSITION(FEED
ROLL 3 SPEED
300mm/s)
761-019 ADJUST TRAY 3 10
PRE FEED STOP
POSITION(TAKE
AWAY ROLL 3
SPEED 450mm/s)
761-020 ADJUST TRAY 4 20
PRE FEED STOP
POSITION(FEED
ROLL 4 SPEED
300mm/s)
General Procedures
dC131PH NVM List (761)
Range Description
0-39 Time from #1 Feed Out SNR ON to #1
Take Away Feed Clutch OFF (Take Away
Roll 220mm/s- Stop timing)
Default=48ms
Range=0-78ms (0-39)
Unit=2ms/step
Default DATA=24 (2ms RTMR)
10-31 Time from #2 Feed Out SNR ON to #2
Feed Motor OFF (Feed Roll 300mm/s-
Stop timing)
Default=40ms
Range=20-62ms (10-31)
Unit=2ms/step
Default DATA=20 (2ms RTMR)
0-31 Time from #2 Feed Out SNR ON to #2
Take Away Feed Clutch OFF (Take Away
Roll 450mm/s - Stop timing)
Default=20ms
Range=0-62ms (0-31)
Unit=2ms/step
Default DATA=10 (2ms RTMR)
10-31 Time from #3 Feed Out SNR ON to #3
Feed Motor OFF (Feed Roll 300mm/s-
Stop timing)
Default=40ms
Range=20-62ms (10-31)
Unit=2ms/step
Default DATA=20 (2ms RTMR)
0-31 Time from #3 Feed Out SNR ON to #3
Take Away Feed Clutch OFF (Take Away
Roll 450mm/s - Stop timing)
Default=20ms
Range=0-62ms (0-31)
Unit=2ms/step
Default DATA=10 (2ms RTMR)
10-31 Time from #4 Feed Out SNR ON to #4
Feed Motor OFF (Feed Roll 300mm/s -
Stop timing)
Default=40ms
Range=20-62ms (10-31)
Unit=2ms/step
Default DATA=20 (2ms RTMR)
Chain-
Link Name
761-021 ADJUST TRAY 4
PRE FEED STOP
POSITION(TAKE
AWAY ROLL 4
SPEED 450mm/s)
761-022 TRAY 1 LIFTER UP
TIME(DURING
FEED)
761-023 TRAY 2 LIFTER UP
TIME(DURING
FEED)
761-024 TRAY 3 LIFTER UP
TIME(DURING
FEED)
761-025 TRAY 4 LIFTER UP
TIME(DURING
FEED)
761-026 TRAY 1 FEED
START TIMING
761-027 TRAY 1 FEED
START TIM-
ING(PANEL B)
1/05
6-48
manuals4you.com manuals4you.com
Table 1 PH NVM List (761)
Default Range Description
10 10-31 Time from #4 Feed Out SNR ON to #4
Take Away Feed Clutch OFF (Take Away
Roll 450mm/s - Stop timing)
Default=20ms
Range=0-62ms (0-31)
Unit=2ms/step
Default DATA=10 (2ms RTMR)
5 0-23 #1 Lift Up time (Applied only to Lift Up
during Feed)
Default=50ms
Range=0-230ms (0-23)
Unit=10ms/step
Default DATA=5 (10ms RTMR)
5 0-23 #2 Lift Up time (Applied only to Lift Up
during Feed)
Default=50ms
Range=0-230ms (0-23)
Unit=10ms/step
Default DATA=5 (10ms RTMR)
5 0-23 #3 Lift Up time (Applied only to Lift Up
during Feed)
Default=50ms
Range=0-230ms (0-23)
Unit=10ms/step
Default DATA=5 (10ms RTMR)
5 0-23 #4 Lift Up time (Applied only to Lift Up
during Feed)
Unit=10ms/step
Default DATA=5 (10ms RTMR)
252 227-277 Time from #1 Take Away Feed Clutch ON
to Registration Motor ON (Feed start)
(Except B side)
Default=504ms
Range=±50ms (±25)
Unit=2ms/step
245 220-270 Time from #1 Take Away Feed Clutch ON
to Registration Motor ON (Feed start) (B
side)
Default=490ms
Range=±50ms (±25)
Unit=2ms/step
DocuColor 12/DCCS50
Reissue