Xerox DocuColor 12/DCCS50 Service Manual page 326

REP 8.3.3 Pressure Roll .................................................................................................
REP 8.3.4 Pressure Roll Heater Rod..............................................................................
REP 8.3.5 Heat Roll Stripper Finger ...............................................................................
REP 8.4.1 Web Motor/EXT-HR Retract Motor ................................................................
REP 8.7.1 Oil Pump ........................................................................................................
REP 8.7.2 Oil Wick..........................................................................................................
REP 8.8.1 External H/R Heater Rod ...............................................................................
REP 8.8.2 External Heat Roll..........................................................................................
REP 8.10.1 Pressure Roll Stripper Finger ......................................................................
9. ELECTRICAL
REP 9.2.1 Opening/Closing the IOT Control PWB Chassis............................................
REP 9.2.2 IOT Drive PWB ..............................................................................................
REP 9.2.3 Half Tone PWB ..............................................................................................
REP 9.3.1 Power Chassis...............................................................................................
REP 9.3.2 IOT LVPS.......................................................................................................
REP 9.3.3 B3/B3H (ESS) LVPS......................................................................................
REP 9.5.1 Control Panel .................................................................................................
REP 9.6 Billing Data PWB Replacement ........................................................................
10. AIR SYSTEM
REP 10.2.1 Fuser Fan ....................................................................................................
REP 10.2.2 Suction Blower Motor...................................................................................
11. COVER
REP 11.1.1 Platen Cushion ............................................................................................
12. DADF
REP 12.1.1 DADF ...........................................................................................................
REP 12.2.2 Registration Gate Solenoid..........................................................................
REP 12.3.1 Left/Right Counter Balance..........................................................................
REP 12.3.2 DADF Control PWB .....................................................................................
REP 12.4.1 Feed Motor ..................................................................................................
REP 12.4.2 Nudger Roll..................................................................................................
REP 12.4.3 Feed Roll .....................................................................................................
REP 12.5.1 Document Feed Lower Chute ......................................................................
REP 12.5.2 Retard Roll...................................................................................................
REP 12.5.3 Set Gate Solenoid........................................................................................
REP 12.5.4 Registration Sensor .....................................................................................
REP 12.5.5 Size Sensors 1/2 (Rear/Front) .....................................................................
REP 12.6.1 DADF Belt Motor..........................................................................................
REP 12.7.1 Duplex Sensor .............................................................................................
REP 12.8.1 Registration Pinch Roll ................................................................................
REP 12.9.1 Exit Motor.....................................................................................................
REP 12.10.1 Platen Belt .................................................................................................
13. MAIL BOX SORTER
REP 13.3.1 Decurler .......................................................................................................
REP 13.5.1 Vertical LED/Sensor ....................................................................................
REP 13.5.2 Bin Tray 1 ....................................................................................................
REP 13.6.1 Bin Trays 2 - 10 ...........................................................................................
REP 13.13.1 Decurler Rolls 1/2 ......................................................................................
REP 13.13.2 Gear and Cam ...........................................................................................
Repairs and Adjustments
4-122 REP 13.14.1 Decurler Stepping Motor ............................................................................
4-125
14. OCT
4-127
REP 14.1.1 Offset Motor .................................................................................................
4-128
4-131
19. IDFE
4-132
REP 19.1 Removing the IDFE.........................................................................................
4-133
REP 19.2 Token Ring PWB (IDFE).................................................................................
4-136
REP 19.3 DIMMs on the Motherboard (IDFE).................................................................
4-137
ADJUSTMENTS
4-139 3. IIT
4-139
ADJ. 3.4.1 Full Rate/Half Rate Carriage Position............................................................
4-141
6. DEVELOPMENT
4-143
ADJ 6.1.1 Rotary Home Position Sensor ........................................................................
4-145
ADJ 6.6.1 Rotary Development Housing Position...........................................................
4-146
4-148
8. FUSER
4-149
ADJ 8.1.1 Fuser Nip (DC701) .........................................................................................
ADJ 8.8.1 External Heat Roll Nip Adjustment .................................................................
4-151
9. ELECTRICAL
4-152
ADJ 9.1.1 MAX SET UP (dC929)....................................................................................
ADJ 9.1.2 IIT Calibration (dC945) ...................................................................................
ADJ 9.1.3 ADC AGC Setup (dC934)...............................................................................
4-153
ADJ 9.1.4 VH/VM Setup (dC933)....................................................................................
ADJ 9.1.5 IOT Highlight Setup (dC918) ..........................................................................
4-155
ADJ 9.1.6 TRC Control/Toner Density (dC922) ..............................................................
4-156
ADJ 9.1.7 TRC Adjust (dC924)/TRC Check PG (dC939) ...............................................
4-156
ADJ 9.1.8 Color Balance Setup (dC919: Copier/Printer) ................................................
4-158
ADJ 9.1.10 IOT Registration Series (dC129) ..................................................................
4-159
ADJ 9.1.14 IIT Lead Edge Registration...........................................................................
4-160
ADJ 9.1.15 IIT Side Edge Registration............................................................................
4-161
ADJ 9.1.16 IIT Horizontal Magnification/Vertical Magnification (IIT Machine).................
4-162
ADJ 9.1.17 Tray 5 Guide (dC740)...................................................................................
4-163
ADJ 9.1.18 Touch Panel Starting Point Correction .........................................................
4-164
ADJ 9.1.19 Tray 2, 3, and 4 for 12 x 18 Paper................................................................
4-165
12. DADF
4-166
ADJ 12.1.1 DADF Side Registration ...............................................................................
4-167
ADJ 12.3.1 Left/Right Counter Balance ..........................................................................
4-168
ADJ 12.3.2 DADF Parallelism .........................................................................................
4-170
ADJ 12.3.3 DADF Height ................................................................................................
4-172
ADJ 12.4.1 DADF Lead Edge Registration .....................................................................
4-173
4-175
4-176
4-177
4-179
4-180
4-182
1/05
4-2
manuals4you.com manuals4you.com
4-184
4-185
4-187
4-188
4-188
4-189
4-193
4-193
4-197
4-197
4-199
4-199
4-200
4-200
4-201
4-201
4-202
4-203
4-203
4-207
4-208
4-209
4-211
4-212
4-213
4-215
4-216
4-217
4-218
4-221
Reissue
DocuColor 12/DCCS50