Table of Contents
Advertisement
11-142 V-Tra In Sensor On Jam Long RAP
The V-Tra In Sensor did not detect the lead edge of the paper within the specified time after the
Decurler Exit Sensor detected the lead edge of the same paper.
NOTE: If this machine has a Finisher/Sorter Accessory, go to Section 8D,
Entrance Sensor On Jam Long RAP
to troubleshoot this Fault Code.
Initial Actions
Refer to BSD11.2 and BSD11.4 for the following procedure.
Check for the following:
•
Obstructions in the Mail Box paper path
•
Bent or out of position paper chutes/guides in the Mail Box paper path
•
Ensure that the Mail Box front Door is closed properly, in order to provide proper nip pres-
sure to the Vertical Transport Rolls.
•
Ensure that connectors
P/J562
on the Mail Box Control PWB and
Sensor are seated correctly and there are no obvious crimped or broken wires.
Procedure
The lead edge of the paper is at or past the V-Tra In Sensor
Y
N
The paper entered the Vertical Transport.
Y
N
The OCT Gate is in the down or Bin Tray position
Y
N
Enter dC330 011-082 OCT Gate Solenoid Bin Tray On. Press Start. The
OCT Gate Solenoid energized.
Y
N
+24 VDC is measured between P/J562-2 and P/J562-3 on the Mail
Box Control PWB.
Y
N
+24 VDC is Measured between P/J562-2 Mail Box Control PWB
and GND
Y
N
+24 VDC is measured between P/J563-1 on the Mail Box
Control PWB and GND.
Y
N
Go to the +24 VDC Wirenet and troubleshoot the wire
between P/J563-1 on the Mail Box Control PWB and
J45-6 on the Distribution PWB
Replace the Mail Box Control PWB
Less than +1 VDC is measured between P/J562-3 and GND
Y
N
Replace the Mail Box Control PWB
Go to
Flag 6
on BSD 11.4. Check the wires for an open circuit. If the
wires are good, replace the OCT Gate Solenoid
A
B
C
D
E
Status Indicator RAPs
11-142 V-Tra In Sensor On Jam Long RAP
A
B
11-142 Mailbox
Enter dC330 011-005 Mailbox Drive Motor. Press Start. The Mail Box Transport Roll
is rotating.
Y
P/J567
on the V-Tra In
P/
(PL
13.10)
Check the following parts for wear, glazing, or slipping.
•
(PL
13.10)
•
•
(PL
13.9).
•
A
1/05
2-192
manuals4you.com
manuals4you.com
C
D
E
Go to
Flag 6
on BSD 11.4. Check the wires for an open circuit. If the wires
are good, ensure that the OCT gate is connected to the OCT Gate Sole-
noid and that it moves freely. If the problem continues replace the OCT
Gate
(PL
13.9) and the OCT Gate Solenoid
Ensure that the OCT gate is connected to the OCT Gate Solenoid and that it
moves freely. If the problem continues replace the OCT Gate
OCT Gate Solenoid
(PL
13.9).
•
Check the paper path for any obstructions that could cause the paper not to
enter the Vertical Transport.
•
Ensure that the OCT gate moves freely. If the problem continues replace the
OCT Gate
(PL
13.9) and the OCT Gate Solenoid
N
The Mail Box Drive Belt is moving.
Y
N
The Mail Box Drive Motor is rotating
Y
N
+24 VDC is measured between P/J572-1 and P/J572-2 of the Mail
Box Drive Motor
Y
N
Go to
Flag 1
on BSD11.2. Check the wires for an open circuit. If the
wires are good, replace the Mail Box Control PWB
Press Stop. +5 VDC is measured between P/J572-3 and GND.
Y
N
Go to
Flag 3
on BSD 11.2. Check the wire for an open circuit. If the
wire is good, replace the Mail Box Control PWB
Press Start. Less than +1 VDC is measured between P/J572-3 and
GND.
Y
N
Replace the Mail Box Control PWB
Replace the Mail Box Drive Motor
Ensure that the Mail Box Drive Motor Pulley is fastened to the motor shaft.
•
Check the Drive Belt Tension Roll for proper tension.
•
Check the Drive Belt for Damage
•
Check that the gear pulleys are properly fastened to the drive rolls
Entrance Roll
(PL
13.9)
Pinch Rollers
(PL
13.9)
Exit Roll
(PL
13.9)
Drive Belt
(PL
13.10)
(PL
13.9).
(PL
13.9) and the
(PL
13.9).
(PL
13.10).
(PL
13.10).
(PL
13.10)
(PL
13.10).
Reissue
DocuColor 12/DCCS50
Advertisement
Table of Contents
Troubleshooting
