Xerox DocuColor 12/DCCS50 Service Manual page 787

Table 2 Output Component Control Codes
ID Description In_Out
004-007 MAIN MOTOR Output
004-009 FUSER MOTOR Output
004-021 DRUM MOTOR Output
005-011 SET GATE SOLENOID Output
OPEN
005-012 SET GATE SOLENOID Output
CLOSE
005-040 FEED MOTOR Output
005-055 BELT MOTOR CW Output
005-056 BELT MOTOR CCW Output
005-075 REGI GATE SOLE- Output
NOID
005-081 EXIT MOTOR Output
005-083 DOC READY Output
005-084 DOC SET LED Output
006-002 ITT EXPOSURE LEAP Output
Reissue
DocuColor 12/DCCS50
Module_I
Smart Help D
The Main Motor rotates at a fre- Processor
quency of 2000.8 Hz
The PR and IVT are turned on
simultaneously
IF you operate the Drum Motor and
the main Motor at the same time,
then start one of them, the other
Motor will shut down. (This is
because they are both using the
same Hard signal)
The fuser motor rotates with a fre- Processor
quency of 1495.886 Hz.
Note: also used with V-TRA
- The drum motor rotates with a Processor
frequency of 1495.886 Hz.
- Drum Motor Gain sell, 2 (low)
- PR and IBT are turned on simul-
taneously
- If you operate the drum motor
and the main motor at the same
time, then stop one of them, the
other motor will slow down. (This is
because they are both using the
same hard signal)
After 5 sec., turned OFF automati- DADF
cally
After 5 sec., turned OFF automati- DADF
cally
After 2 sec., turned OFF automati- DADF
cally
The DADF Belt Motor forwards DADF
Belt Motor (Normal rotation) DADF
The DADF Belt Motor reverses
After 5 sec., turned OFF automati- DADF
cally
On: Rotates DADF
Simultaneous Output item: (IISS DADF
sheet abort)
On: L DADF
After 180 sec., Turns OFF automat- IIT
ically
Table 2 Output Component Control Codes
ID Description
006-003 COOLING FAN LOW
SPEED
006-005 IIT SCAN MOTOR
(Scan)
006-006 IIT SCAN MOTOR
(Return)
006-007 FUSER CUT
006-013 COOLING FAN HIGH
SPEED
006-086 IIT IMAGE AREA
006-091 EXCHANGE TO ADF
007-078 HCF FEED CLUTCH
007-079 HCF ELEVATE MOTOR Output
007-080 HCF FEED MOTOR
008-006 #1 NUDGER ROLL
SOLENOID
008-007 #1 FEED MOTOR CCW Output
008-008 #1 FEED MOTOR CW
008-009 #1 TAKE AWAY FEED
CLUTCH
008-011 #2 NUDGER ROLL
SOLENOID
008-012 #2 FEED MOTOR CCW Output
1/05
6-107
In_Out Smart Help
Output ON: L
Cooling Fan: High
Output Moves the Carriage 50mm in the
scan direction and stops automati-
cally
Output IIT Scan Motor (Return)
Output On: Active
Output On: L
Output On: Active
Output On: Active
Simultaneous on item
Output Engages the HCF Nudger Roll to
the Feed Motor.
Unidirectional Motor to move the
HFC Paper Tray in the up direction
only (motor is not engaged in the
down direction).
Output Unipolar 200 step / rev stepper
motor with a maximum 800 PPS.
One revolution = 200 steps = 152
mm paper travel.
Output ON time is 2000 msec
Motor reverse. Tray lift up (upper
limit detection stop)
ON time: 5500 msec
Output Motor normal rotation: Feed Roll
rotation
Output On drives connection
Output ON time is 2000 msec
Motor reverse: Tray lift up (upper
limit detection stop)
Does not turn on if the tray is not
set
ON time: 6000 msec
General Procedures
dC330 Component Control
Module_I
D
IIT
IIT
IIT
IIT
IIT
IIT
IIT
HCF
HCF
HCF
Processor
Processor
Processor
Processor
Processor
Processor