Xerox DocuColor 12/DCCS50 Service Manual page 790

Table 2 Output Component Control Codes
ID Description In_Out
009-081 CHARGE COROTRON Output
GRID
009-085 ROTARY MOT FAN Output
009-088 BLOWER Output
009-089 CC FAN Output
010-004 FUSER FAN-LOW Output
SPEED
010-005 INVERT GATE SOLE- Output
NOID INVERT
010-006 INVERT GATE SOLE- Output
NOID EXIT
010-018 FUSER FAN-HIGH Output
SPEED
010-020 INVERT MOTOR CW Output
010-021 INVERT MOTOR CCW Output
010-023 PRESSURE ROLL Output
CONTACT
General Procedures
dC330 Component Control
Module_I
Smart Help D
Run simultaneously with Drum Processor
Motor (004-021)
ON: PWM Output Value = 717
(NVM 774-005)
ON: L Processor
ON: L Processor
ON: L Processor
ON: Port H Processor
NOTE: When you exit from the I/O
check, exit at high speed.
Cannot run with Fuser Fan High
Speed (010-018).
ON (INV): L Processor
Reverse: Keep the state
ON time: 100 msec
Cannot run with Invert Gate Sole-
noid Exit (010-006)
On (Exit): L Processor
Reverse: Keep the state
ON time: 100 msec
Cannot run with Invert Gate Sole-
noid Invert (010-005).
ON: L Processor
NOTE: When you exit from the I/O
check, exit at high speed.
Cannot run with Fuser Fan Low
Speed (010-004)
Motor On: Port (L) [CW] normal Processor
rotation (upward): Port (H) Motor
Speed = 350 mm/s
Cannot run with Invert Motor CW
Motor On: Port (L) [CCW] reverse Processor
rotation (downward): Port (L) Motor
Speed = 450 mm/s
Cannot run with Invert Motor CW
Turn on Exit Motor (010-040) simul- Processor
taneously.
ON: L
Automatically turns off after Pres-
sure Roll Retract Sensor detects
the contact position.
Cannot run with Fuser Nip CL OFF
(010-024).
Table 2 Output Component Control Codes
ID Description
010-024 PRESSURE ROLL
RETRACT
010-025 INVERT ROLL NIP
SOLENOID
010-026 INVERT ROLL
RELEASE SOLENOID
010-027 EXTERNAL HEAT
ROLL CONTACT
010-028 EXTERNAL HEAT
ROLL RETRACT
010-029 EXTERNAL HEAT
ROLL LAMP
1/05
6-110
manuals4you.com manuals4you.com
In_Out Smart Help
Output Turn on Exit Motor (010-040) simul-
taneously.
ON: L
Automatically turns off after Pres-
sure Roll Retract Sensor detects
the contact position.
Cannot run with Fuser Nip CL OFF
(010-023).
Output On (Roll Nip): L
Reverse: Keep the state.
ON time: 100 msec
Cannot run with Invert Nip Solenoid
Release (010-026).
Output On (Roll Nip): L
Reverse: Keep the state.
ON time: 100 msec
Cannot run with Invert Nip Solenoid
Release (010-025).
Output ON: L
Automatically turns off after the
External Heat Roll Retract Sensor
detects the Contact position.
Cannot run with External Heat Roll
Retract Motor - Retract (010-028)
Output ON: L
Automatically turns off after the
External Heat Roll Retract Sensor
detects the Contact position.
Cannot run with External Heat Roll
Retract Motor - Retract (010-027)
Output ON: L
Automatically turns off after 1 sec.
NOTE: The fuser temperature con-
trol will be halted during the Diag.
Component Control and Diag. sub-
system check. The fuser tempera-
ture control continues in any other
Diag.
DocuColor 12/DCCS50
Module_I
D
Processor
Processor
Processor
Processor
Processor
Processor
Reissue