Huawei Quidway S3700 Series Configuration Manual page 94

Quidway S3700 Series Ethernet Switches
Configuration Guide - Reliability
# On SwitchA, configure domain 1. Then configure VLAN 10 as the main control VLAN and
instance 1 as the protected instance of domain 1.
[SwitchA] rrpp enable
[SwitchA] rrpp domain 1
[SwitchA-rrpp-domain-region1] control-vlan 10
[SwitchA-rrpp-domain-region1] protected-vlan reference-instance 1
[SwitchA-rrpp-domain-region1] quit
# Disable STP on the interfaces to be added to the RRPP rings, configure the interfaces as trunk
interfaces, and configure the interfaces to allow service packets of VLAN 2 to VLAN 9 to pass
through.
[SwitchA] interface ethernet 0/0/1
[SwitchA-Ethernet0/0/1] port link-type trunk
[SwitchA-Ethernet0/0/1] port trunk allow-pass vlan 2 to 9
[SwitchA-Ethernet0/0/1] stp disable
[SwitchA-Ethernet0/0/1] quit
[SwitchA] interface ethernet 0/0/2
[SwitchA-Ethernet0/0/2] port link-type trunk
[SwitchA-Ethernet0/0/2] port trunk allow-pass vlan 2 to 9
[SwitchA-Ethernet0/0/2] stp disable
[SwitchA-Ethernet0/0/2] quit
[SwitchA] interface ethernet 0/0/3
[SwitchA-Ethernet0/0/3] port link-type trunk
[SwitchA-Ethernet0/0/3] port trunk allow-pass vlan 2 to 9
[SwitchA-Ethernet0/0/3] stp disable
[SwitchA-Ethernet0/0/3] quit
# Configure the primary interface and secondary interface of the transit node on the RRPP major
ring.
[SwitchA] rrpp domain 1
[SwitchA-rrpp-domain-region1] ring 1 node-mode transit primary-port ethernet 0/0/2
secondary-port ethernet 0/0/1 level 0
[SwitchA-rrpp-domain-region1] ring 1 enable
[SwitchA-rrpp-domain-region1] quit
# Configure the common interface and edge interface of the edge transit node on the subring.
[SwitchA] rrpp domain 1
[SwitchA-rrpp-domain-region1] ring 2 node-mode edge common-port ethernet 0/0/2
edge-port ethernet 0/0/3
[SwitchA-rrpp-domain-region1] ring 2 enable
[SwitchA-rrpp-domain-region1] quit
Step 4 Configure Switch D as the transit node of the major ring and the assistant edge node of the
subring.
# Create data VLANs 2 to 9 on Switch D.
<Quidway> system-view
[Quidway] sysname SwitchD
[SwitchD] vlan batch 2 to 9
Configure instance 1, and map it to the VLANs allowed by the RRPP interfaces and protected
VLANs.
[SwitchD] stp region-configuration
[SwitchD-mst-region] instance 1 vlan 2 to 11
[SwitchD-mst-region] active region-configuration
[SwitchD-mst-region] quit
# On Switch D, configure domain 1. Then configure VLAN 10 as the main control VLAN and
instance 1 as the protected instance of domain 1.
[SwitchD] rrpp enable
[SwitchD] rrpp domain 1
Issue 01 (2011-10-26) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
3 RRPP Configuration
82