Huawei Quidway S3700 Series Configuration Manual page 88

Quidway S3700 Series Ethernet Switches
Configuration Guide - Reliability
[SwitchB] interface ethernet 0/0/1
[SwitchB-Ethernet0/0/1] port link-type trunk
[SwitchB-Ethernet0/0/1] port trunk allow-pass vlan 100 to 300
[SwitchB-Ethernet0/0/1] stp disable
[SwitchB-Ethernet0/0/1] quit
[SwitchB] interface ethernet 0/0/2
[SwitchB-Ethernet0/0/2] port link-type trunk
[SwitchB-Ethernet0/0/2] port trunk allow-pass vlan 100 to 300
[SwitchB-Ethernet0/0/2] stp disable
[SwitchB-Ethernet0/0/2] quit
# Configure Switch C.
[SwitchC] interface ethernet 0/0/1
[SwitchC-Ethernet0/0/1] port link-type trunk
[SwitchC-Ethernet0/0/1] port trunk allow-pass vlan 100 to 300
[SwitchC-Ethernet0/0/1] stp disable
[SwitchC-Ethernet0/0/1] quit
[SwitchC] interface ethernet 0/0/2
[SwitchC-Ethernet0/0/2] port link-type trunk
[SwitchC-Ethernet0/0/2] port trunk allow-pass vlan 100 to 300
[SwitchC-Ethernet0/0/2] stp disable
[SwitchC-Ethernet0/0/2] quit
Step 4 Configure a protection VLAN and create the RRPP ring.
# Configure the protection VLAN on Switch A and configure Switch A as the master node of
RRPP ring 1 and specify the primary interface and secondary interface.
[SwitchA] rrpp domain 1
[SwitchA-rrpp-domain-region1] protected-vlan reference-instance 1
[SwitchA-rrpp-domain-region1] ring 1 node-mode master primary-port ethernet 0/0/1
secondary-port ethernet 0/0/2 level 0
[SwitchA-rrpp-domain-region1] ring 1 enable
[SwitchA-rrpp-domain-region1] quit
# Configure the protection VLAN on Switch B and configure Switch B as the transit node of
RRPP ring 1 and specify the primary interface and secondary interface.
[SwitchB] rrpp domain 1
[SwitchB-rrpp-domain-region1] protected-vlan reference-instance 1
[SwitchB-rrpp-domain-region1] ring 1 node-mode transit primary-port ethernet 0/0/1
secondary-port ethernet 0/0/2 level 0
[SwitchB-rrpp-domain-region1] ring 1 enable
[SwitchB-rrpp-domain-region1] quit
# Configure the protection VLAN on Switch C and configure Switch C as the transit node of
RRPP ring 1 and specify the primary interface and secondary interface.
[SwitchC] rrpp domain 1
[SwitchC-rrpp-domain-region1] protected-vlan reference-instance 1
[SwitchC-rrpp-domain-region1] ring 1 node-mode transit primary-port ethernet 0/0/1
secondary-port ethernet 0/0/2 level 0
[SwitchC-rrpp-domain-region1] ring 1 enable
[SwitchC-rrpp-domain-region1] quit
Step 5 Enable RRPP.
After configuring an RRPP ring, enable RRPP on each node on the ring so that the RRPP ring
can be activated.
# Enable RRPP on Switch A.
[SwitchA] rrpp enable
# Enable RRPP on SwitchB.
[SwitchB] rrpp enable
Issue 01 (2011-10-26) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
3 RRPP Configuration
76