Huawei Quidway S3700 Series Configuration Manual page 115

Quidway S3700 Series Ethernet Switches
Configuration Guide - Reliability
# Configure the VLANs mapping instance 2 as the protected VLANs in domain 2. Configure
VLAN 10 as the control VLAN.
[PE-AGG] rrpp domain 2
[PE-AGG-rrpp-domain-region2] protected-vlan reference-instance 2
[PE-AGG-rrpp-domain-region2] control-vlan 10
[PE-AGG-rrpp-domain-region2] quit
Step 4 Create RRPP rings.
l Configure UPE A.
# Configure UPE A as a transit node of ring 1 in domain 1 and specify primary and secondary
ports on UPE A.
[UPEA] rrpp domain 1
[UPEA-rrpp-domain-region1] ring 1 node-mode transit primary-port ethernet 0/0/1
secondary-port ethernet 0/0/2 level 0
[UPEA-rrpp-domain-region1] ring 1 enable
[UPEA-rrpp-domain-region1] quit
# Configure UPE A as a transit node of ring 1 in domain 2 and specify primary and secondary
ports on UPE A.
[UPEA] rrpp domain 2
[UPEA-rrpp-domain-region2] ring 1 node-mode transit primary-port ethernet 0/0/1
secondary-port ethernet 0/0/2 level 0
[UPEA-rrpp-domain-region2] ring 1 enable
[UPEA-rrpp-domain-region2] quit
l # Configure UPE B.
# Configure UPE B as a transit node of ring 1 in domain 1 and specify primary and secondary
ports on UPE B.
[UPEB] rrpp domain 1
[UPEB-rrpp-domain-region1] ring 1 node-mode transit primary-port ethernet 0/0/1
secondary-port ethernet 0/0/2 level 0
[UPEB-rrpp-domain-region1] ring 1 enable
[UPEB-rrpp-domain-region1] quit
# Configure UPE B as a transit node of ring 1 in domain 2 and specify primary and secondary
ports on UPE B.
[UPEB] rrpp domain 2
[UPEB-rrpp-domain-region2] ring 1 node-mode transit primary-port ethernet 0/0/1
secondary-port ethernet 0/0/2 level 0
[UPEB-rrpp-domain-region2] ring 1 enable
[UPEB-rrpp-domain-region2] quit
l Configure UPE C.
# Configure UPE C as a transit node of ring 1 in domain 1 and specify primary and secondary
ports on UPE C.
[UPEC] rrpp domain 1
[UPEC-rrpp-domain-region1] ring 1 node-mode transit primary-port ethernet 0/0/1
secondary-port ethernet 0/0/2 level 0
[UPEC-rrpp-domain-region1] ring 1 enable
[UPEC-rrpp-domain-region1] quit
# Configure UPE C as a transit node of ring 1 in domain 2 and specify primary and secondary
ports on UPE C.
[UPEC] rrpp domain 2
[UPEC-rrpp-domain-region2] ring 1 node-mode transit primary-port ethernet 0/0/1
secondary-port ethernet 0/0/2 level 0
[UPEC-rrpp-domain-region2] ring 1 enable
[UPEC-rrpp-domain-region2] quit
Issue 01 (2011-10-26) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
3 RRPP Configuration
103