Huawei Quidway S3700 Series Configuration Manual page 266
Hide thumbs
Also See for Quidway S3700 Series:
- Configuration manual (289 pages) ,
- Quick start manual (70 pages) ,
- Manual (69 pages)
Table of Contents
Advertisement
Quidway S3700 Series Ethernet Switches
Configuration Guide - Reliability
Step 6 Configure Ethernet CFM.
# Configure UPEA.
[UPEA] cfm md md1
[UPEA-md-md1] ma ma1
[UPEA-md-md1-ma-ma1]
[UPEA-md-md1-ma-ma1] mep mep-id 1 interface ethernet 0/0/2 outward
[UPEA-md-md1-ma-ma1] remote-mep mep-id 2
[UPEA-md-md1-ma-ma1] remote-mep ccm-receive mep-id 2 enable
[UPEA-md-md1-ma-ma1] mep ccm-send enable
[UPEA-md-md1-ma-ma1] quit
[UPEA-md-md1] ma ma2
[UPEA-md-md1-ma-ma2]
[UPEA-md-md1-ma-ma2] mep mep-id 3 interface ethernet 0/0/1 outward
[UPEA-md-md1-ma-ma2] remote-mep mep-id 4
[UPEA-md-md1-ma-ma2] remote-mep ccm-receive mep-id 4 enable
[UPEA-md-md1-ma-ma2] mep ccm-send enable
[UPEA-md-md1-ma-ma2] quit
[UPEA-md-md1] quit
# Configure PE-AGG.
[PE-AGG] cfm md md1
[PE-AGG-md-md1] ma ma1
[PE-AGG-md-md1-ma-ma1]
[PE-AGG-md-md1-ma-ma1] mep mep-id 2 interface ethernet 0/0/1 outward
[PE-AGG-md-md1-ma-ma1] remote-mep mep-id 1
[PE-AGG-md-md1-ma-ma1] remote-mep ccm-receive mep-id 1 enable
[PE-AGG-md-md1-ma-ma1] mep ccm-send enable
[PE-AGG-md-md1-ma-ma1] quit
[PE-AGG-md-md1] ma ma2
[PE-AGG-md-md1-ma-ma2]
[PE-AGG-md-md1-ma-ma2] mep mep-id 4 interface ethernet 0/0/2 outward
[PE-AGG-md-md1-ma-ma2] remote-mep mep-id 3
[PE-AGG-md-md1-ma-ma2] remote-mep ccm-receive mep-id 3 enable
[PE-AGG-md-md1-ma-ma2] mep ccm-send enable
[PE-AGG-md-md1-ma-ma2] quit
[PE-AGG-md-md1] quit
Issue 01 (2011-10-26)
---------------------------------------------------------------------------
1
0
M
The preceding information shows that RRPP is enabled on PE-AGG. In domain 1, VLAN 5
is the major control VLAN, VLANs mapping instance 1 are the protected VLANs, and PE-
AGG is the master node on ring 1; Eth 0/0/1 is the primary interface, and Eth 0/0/2 is the
secondary interface.
# Check detailed information about PE-AGG in domain 1.
[PE-AGG] display rrpp verbose domain 1
Domain Index
: 1
Control VLAN
: major 5
Protected VLAN: Reference Instance 1
ello Timer
: 1 sec(default is 1 sec)
RRPP Ring
: 1
Ring Level
: 0
Node Mode
: Master
Ring State
: Complete
Is Enabled
: Enable
Primary port
: Ethernet0/0/1
Secondary port: Ethernet0/0/2
The preceding information shows that VLAN 5 is the control VLAN in domain 1, and VLANs
mapping instance 1 are the protected VLANs. PE-AGG is the master node in domain 1 and
is in Complete state. Eth 0/0/1 is the primary interface, and Eth 0/0/2 is the secondary
interface.
map vlan 100
map vlan 100
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
Ethernet0/0/1
sub 6
Fail Timer : 3 sec(default is 3 sec)
Is Active : Yes
map vlan 100
map vlan 100
4 Ethernet OAM Configuration
Ethernet0/0/2
Port status: UP
Port status: BLOCKED
Yes
254
Advertisement
Table of Contents
