Konica Minolta bizhub C658 Service Manual page 61

6.1.2 Alignment plate...........................................................................................................................................................PL-13
6.1.3 Exit section .................................................................................................................................................................PL-14
6.2 Drive ....................................................................................................................................................................................PL-14
6.2.1 Upper paddle ..............................................................................................................................................................PL-14
6.2.2 Alignment plate...........................................................................................................................................................PL-15
6.2.3 Exit section .................................................................................................................................................................PL-15
6.3 Operation .............................................................................................................................................................................PL-15
6.3.1 Upper paddle ..............................................................................................................................................................PL-15
6.3.2 Alignment plate...........................................................................................................................................................PL-16
6.3.3 Exit section .................................................................................................................................................................PL-17
6.3.4 Stack support plate control .........................................................................................................................................PL-19
7. STAPLER SECTION ............................................................................................................................................PL-20
7.1 Configuration .......................................................................................................................................................................PL-20
7.2 Drive ....................................................................................................................................................................................PL-20
7.3 Operation .............................................................................................................................................................................PL-20
7.3.1 Stapler position detection ...........................................................................................................................................PL-20
7.3.2 Staple control..............................................................................................................................................................PL-21
8. OUTPUT TRAY SECTION ................................................................................................................................... PL-22
8.1 Configuration .......................................................................................................................................................................PL-22
8.2 Drive ....................................................................................................................................................................................PL-22
8.3 Operation .............................................................................................................................................................................PL-23
8.3.1 Main tray up/down mechanism...................................................................................................................................PL-23
8.3.2 Main tray paper detection ...........................................................................................................................................PL-23
8.3.3 Tray full detection mechanism....................................................................................................................................PL-25
9. SADDLE SECTION FS-537SD ............................................................................................................................ PL-26
9.1 Configuration .......................................................................................................................................................................PL-26
9.2 Transport section .................................................................................................................................................................PL-27
9.2.1 Drive ...........................................................................................................................................................................PL-27
9.2.2 Paper transport...........................................................................................................................................................PL-27
9.2.3 Curl cover ...................................................................................................................................................................PL-27
9.3 Alignment section ................................................................................................................................................................PL-29
9.3.1 Drive ...........................................................................................................................................................................PL-29
9.3.2 Alignment....................................................................................................................................................................PL-29
9.3.3 Stopper guide .............................................................................................................................................................PL-30
9.4 Stapler .................................................................................................................................................................................PL-31
9.4.1 Drive ...........................................................................................................................................................................PL-31
9.4.2 Operation....................................................................................................................................................................PL-32
9.5 Folding/Saddle stitching.......................................................................................................................................................PL-33
9.5.1 Drive ...........................................................................................................................................................................PL-33
9.5.2 Folding knife ...............................................................................................................................................................PL-33
9.6 Tri-folding.............................................................................................................................................................................PL-35
9.6.1 Drive ...........................................................................................................................................................................PL-35
9.6.2 Tri-folding operation....................................................................................................................................................PL-35
9.7 Exit section ..........................................................................................................................................................................PL-36
9.7.1 Drive ...........................................................................................................................................................................PL-36
9.7.2 Paper exit ...................................................................................................................................................................PL-37
9.7.3 Paper transport belt ....................................................................................................................................................PL-38
10. PK-523 ............................................................................................................................................................... PL-40
10.1 Configuration .....................................................................................................................................................................PL-40
10.2 Drive ..................................................................................................................................................................................PL-40
10.2.1 Punch shift section ...................................................................................................................................................PL-40
10.2.2 Punch section ...........................................................................................................................................................PL-40
10.3 Operation...........................................................................................................................................................................PL-41
10.3.1 Punch standby position movement control............................................................................................................... PL-41
10.3.2 Punch position correction control ............................................................................................................................. PL-41
10.3.3 Punch control............................................................................................................................................................PL-42
10.3.4 Punch scraps box control .........................................................................................................................................PL-43
11. ZU-609 ............................................................................................................................................................... PL-44
11.1 Configuration .....................................................................................................................................................................PL-44
11.2 Drive ..................................................................................................................................................................................PL-44
11.2.1 1st folding .................................................................................................................................................................PL-44
11.2.2 2nd folding/transport.................................................................................................................................................PL-44
11.3 Operation...........................................................................................................................................................................PL-45
11.3.1 1st folding mechanism..............................................................................................................................................PL-45
11.3.2 2nd folding mechanism.............................................................................................................................................PL-46
lx