Konica Minolta bizhub C658 Service Manual page 938

bizhub C658/C558/C458/C368/C308/C258
• Applicable units are the following units that have the new unit detection feature.
Drum unit (each color), developing unit (each color)
• See the " I.7.3.9 (4) Notes when using the New Release Disable
5.17.3 Service Call
(1) Use
• To count and display how many times trouble has been detected on a trouble type basis.
• Use this feature to check how many times trouble has occurred.
NOTE
▪ In the service call counter list, "Reboot" shows how many times abort code (C-FXXX) has occurred.
5.17.4 Section Service Call
(1) Use
• To count and display how many times trouble has been detected during a certain period, i.e. an interval between service visits, on a
trouble type basis.
• Use this feature to check how many times trouble has occurred in a certain period, i.e. an interval between service visits.
• By clearing the counter at the time of visit to your customer, i.e. service visit, you can check how many times trouble has occurred since
the previous visit.
To reset the counter, use [Counter Reset].
NOTE
▪ In the zone service call list, "Reboot" shows how many times abort code (C-FXXX) has occurred.
5.17.5 Warning
(1) Use
• To count and display how many times malfunction code has been detected on a malfunction code type basis.
• To count and display how many times tray lift-up failure occur on a tray type.
• To clear of count value.
• To check the number of warning conditions detected according to the warming type.
(2) Procedure
• To clear the count of a counter, select the specific part and touch Clear.
• If a counter is cleared mistakenly, touch Interrupt which will undo the clearing operation.
5.17.6 Maintenance
(1) Use
• To set a count value for maintenance of any given part.
• When any given part is replaced.
(2) Procedure
Maint.-Set
• Enter the maintenance counter value from the 10-key pad.
Maint.-Count
• The number of sheets that have been ejected is counted up. (1 sided: 1 count, 2 sided: 2 count)
• Touch Clear will clear the count.
5.17.7 Service Total
(1) Total
(a) Use
• To display the count value for the service total counter.
• Use to check the total No. of printed pages including the ones printed by the Service Mode.
(b) Procedure
• Service Total: No. of pages printed by user mode and Service Mode.
• Service Total (Duplex): No. of pages printed by user mode and Service Mode in duplex.
(2) Paper Size 1/Paper Size 2
(a) Use
• To display the count value for service total counter of each paper size.
• To check the total number of printed pages including the one at Service Mode according to each paper size.
• The count of Paper Size 1 and Paper Size 2 that contain the following paper sizes is provided respectively.
Paper Size 1
Paper Size 2
5.17.8 Counter of Each Mode
(1) Use
• To display the printed pages in the following specified modes; copy, printer, scanner, and fax. It also displays the count value of using the
specified mode.
Copy/Print/Scanner counter
SRA3, A3, A4, A4S, A5, A6, B4, B5, B5S, B6, Post., 12 x 18, 11 x 17, 8
1 1 1
10 / , 5 / x 8 / , 4 x 6, Foolscap
2 2 2
8K, 16K, Banner Paper, Others
Displays individual counts in copy, printer, and scan mode.
I ADJUSTMENT/SETTING > 5. SERVICE MODE
mode" for the method of enabling the New Release Disable mode.
I-168
1 1 1
/ x 14, 8 / x 11, 8 / x 11S, 7
2 2 2
1
/ x
4