Honda Accord 2008 Manual page 1211

07/11/02 09:23:29 61TA0000_140_0368
Shafts and Clutches
Clutch Clearance Inspection (cont'd)
14. If the clearance (A) is out of the service limit, select
a new clutch end-plate from the following table.
＊１０
1ST CLUTCH END-PLATES
Mark
1
2
3
4
5
6
7
8
9
2ND CLUTCH END-PLATES
Mark
10
11
1
2
3
4
5
6
7
14-366
Part Number Thickness
22571-R90-003 or 2.6 mm (0.102 in.)
22571-RZH-003
22572-R90-003 or 2.7 mm (0.106 in.)
22572-RZH-003
22573-R90-003 or 2.8 mm (0.110 in.)
22573-RZH-003
22574-R90-003 or 2.9 mm (0.114 in.)
22574-RZH-003
22575-R90-003 or 3.0 mm (0.118 in.)
22575-RZH-003
22576-R90-003 or 3.1 mm (0.122 in.)
22576-RZH-003
22577-R90-003 or 3.2 mm (0.126 in.)
22577-RZH-003
22578-R90-003 or 3.3 mm (0.130 in.)
22578-RZH-003
22579-R90-003 or 3.4 mm (0.134 in.)
22579-RZH-003
Part Number Thickness
22569-R90-003 or 2.4 mm (0.094 in.)
22569-RZH-003
22570-R90-003 or 2.5 mm (0.098 in.)
22570-RZH-003
22571-R90-003 or 2.6 mm (0.102 in.)
22571-RZH-003
22572-R90-003 or 2.7 mm (0.106 in.)
22572-RZH-003
22573-R90-003 or 2.8 mm (0.110 in.)
22573-RZH-003
22574-R90-003 or 2.9 mm (0.114 in.)
22574-RZH-003
22575-R90-003 or 3.0 mm (0.118 in.)
22575-RZH-003
22576-R90-003 or 3.1 mm (0.122 in.)
22576-RZH-003
22577-R90-003 or 3.2 mm (0.126 in.)
22577-RZH-003
3RD CLUTCH END-PLATES
Mark Part Number
1 22551-R90-003 or
22551-RZH-003
2 22552-R90-003 or
22552-RZH-003
3 22553-R90-003 or
22553-RZH-003
A
4 22554-R90-003 or
22554-RZH-003
5 22555-R90-003 or
22555-RZH-003
6 22556-R90-003 or
22556-RZH-003
7 22557-R90-003 or
22557-RZH-003
8 22558-R90-003 or
22558-RZH-003
9 22559-R90-003 or
22559-RZH-003
4TH and 5TH CLUTCH END-PLATES
Mark Part Number
1 22581-R90-003 or
22581-R91-003
2 22582-R90-003 or
22582-R91-003
3 22583-R90-003 or
22583-R91-003
4 22584-R90-003 or
22584-R91-003
5 22585-R90-003 or
22585-R91-003
6 22586-R90-003 or
22586-R91-003
7 22587-R90-003 or
22587-R91-003
8 22588-R90-003 or
22588-R91-003
9 22589-R90-003 or
22589-R91-003
15. Install a new clutch end-plate, and recheck the
clearance. If the thickest clutch end-plate is
installed, but the clearance is still over the service
limit, replace the clutch discs and the plates.
Thickness
2.1 mm (0.083 in.)
2.2 mm (0.087 in.)
2.3 mm (0.091 in.)
2.4 mm (0.094 in.)
2.5 mm (0.098 in.)
2.6 mm (0.102 in.)
2.7 mm (0.106 in.)
2.8 mm (0.110 in.)
2.9 mm (0.114 in.)
Thickness
2.1 mm (0.083 in.)
2.2 mm (0.087 in.)
2.3 mm (0.091 in.)
2.4 mm (0.094 in.)
2.5 mm (0.098 in.)
2.6 mm (0.102 in.)
2.7 mm (0.106 in.)
2.8 mm (0.110 in.)
2.9 mm (0.114 in.)