Juniper JUNOSE SOFTWARE 11.0.X - LINK LAYER CONFIGURATION GUIDE 4-1-2010 Configuration Manual page 415
For e series broadband services routers - link layer configuration
Hide thumbs
Also See for JUNOSE SOFTWARE 11.0.X - LINK LAYER CONFIGURATION GUIDE 4-1-2010:
- Configuration manual (788 pages)
Table of Contents
Advertisement
The packet trace log for a PPPoE interface displays only the first 256 bytes of
packet data. Data in excess of 256 bytes does not appear in the packet trace log.
You also configure logging to direct the output to a specific destination. For
information, see Overview of System Logging.
Example
host1(config-if)#ip address 164.10.6.71 255.255.255.0
host1(config-if)#log severity debug pppoeControlPacket atm 10/0.1
host1:v0#DEBUG 07/25/2000 15:13:19 pppoeControlPacket (interface atm
10/0.1): PADI rx from 00-09-01-a0-00-2e
DEBUG 07/25/2000 15:13:19 pppoeControlPacket (interface atm 10/0.1): PADO
tx to 00-09-01-a0-00-2e
DEBUG 07/25/2000 15:13:19 pppoeControlPacket (interface atm 10/0.1): PADR
rx from 00-09-01-a0-00-2e
DEBUG 07/25/2000 15:13:19 pppoeControlPacket (interface atm 10/0.1): PADS
tx to 00-09-01-a0-00-2e, connection made
interface 1
RX-a0-00-2e:v0#
RX-a0-00-2e:v0#
RX-a0-00-2e:v0#
RX-a0-00-2e:v0#
RX-a0-00-2e:v0#
RX-a0-00-2e:v0#
RX-a0-00-2e:v0#config t
Enter configuration commands, one per line.
RX-a0-00-2e:v0(config)#interface atm 10/1.1.1
RX-a0-00-2e:v0(config-if)#ppp shut
RX-a0-00-2e:v0(config-if)#DEBUG 07/25/2000 15:13:38 pppoeControlPacket
(interface atm 10/0.1): PADT rx from 00-09-01-a0-00-2e
RX-a0-00-2e:v0(config-if)#
RX-a0-00-2e:v0(config-if)#no ppp shut
RX-a0-00-2e:v0(config-if)#pppoe test
RX-a0-00-2e:v0(config-if)#DEBUG 07/25/2000 15:13:49 pppoeControlPacket
(interface atm 10/0.1): PADI rx from 00-09-01-a0-00-2e
DEBUG 07/25/2000 15:13:49 pppoeControlPacket (interface atm 10/0.1): PADO
tx to 00-09-01-a0-00-2e
DEBUG 07/25/2000 15:13:49 pppoeControlPacket (interface atm 10/0.1): PADR
rx from 00-09-01-a0-00-2e
DEBUG 07/25/2000 15:13:49 pppoeControlPacket (interface atm 10/0.1): PADS
tx to 00-09-01-a0-00-2e, connection made
interface 1
RX-a0-00-2e:v0(config-if)#
RX-a0-00-2e:v0(config-if)#exit
See log severity.
Chapter 10: Configuring Point-to-Point Protocol over Ethernet
using session id 3 on sub
End with CNTL/Z.
using session id 4 on sub
Troubleshooting
385
Advertisement
Table of Contents
Troubleshooting
Related Manuals for Juniper JUNOSE SOFTWARE 11.0.X - LINK LAYER CONFIGURATION GUIDE 4-1-2010
Related Products for Juniper JUNOSE SOFTWARE 11.0.X - LINK LAYER CONFIGURATION GUIDE 4-1-2010
- Juniper JUNOS SOFTWARE 10.2 - SOFTWARE INSTALLATION AND UPGRADE GUIDE 4-28-2010
- Juniper JUNOS OS 10.3 - XML MANAGEMENT PROTOCOL GUIDE 6-30-2010
- Juniper JUNOS 10.1 - CONFIGURATION GUIDE 1-2010
- Juniper JUNOSE 11.1.X - BROADBAND ACCESS CONFIGURATION GUIDE 6-4-2010
- Juniper JUNOSE SOFTWARE 11.1.X - BROADBAND ACCESS CONFIGURATION GUIDE 6-6-2010
- Juniper JUNOSE 11.1.X - QUALITY OF SERVICE CONFIGURATION GUIDE 3-21-2010
- Juniper JUNOSE SOFTWARE 11.2.X - BROADBAND ACCESS CONFIGURATION GUIDE 7-20-2010
- Juniper JUNOSE SOFTWARE 11.2.X - LINK LAYER CONFIGURATION GUIDE 7-7-2010
- Juniper JUNOSE SOFTWARE FOR E SERIES 11.0.X - BGP AND MPLS CONFIGURATION GUIDE 2009-12-30
- Juniper JUNOSE SOFTWARE FOR E SERIES 11.3.X - BGP AND MPLS CONFIGURATION GUIDE 2010-10-12
- Juniper JUNOSE SOFTWARE FOR E SERIES 11.3.X - IP SERVICES CONFIGURATION GUIDE 2010-10-01
- Juniper JUNOSE SOFTWARE FOR E SERIES 11.3.X - MULTICAST ROUTING CONFIGURATION GUIDE 2010-10-07
- Juniper JUNOSE SOFTWARE FOR E SERIES 11.3.X - PHYSICAL LAYER CONFIGURATION GUIDE 2010-09-24
- Juniper JUNOSE SOFTWARE FOR E SERIES 11.3.X - POLICY MANAGEMENT CONFIGURATION GUIDE 2010-10-04
- Juniper JUNOSE SOFTWARE FOR E SERIES 11.3.X - SERVICE AVAILABILITY CONFIGURATION GUIDE 2010-10-08
- Juniper JUNOSE SOFTWARE FOR E SERIES 11.3.X - LINK LAYER CONFIGURATION GUIDE 2010-10-13