Olivetti d-Copia 6500MF Plus Service Manual page 483

No. Content
Lock-up at Welcome display
- (The display unchages after
60 seconds or more)
CF000 appears in 60
seconds after the Welcome
display continues
F000 Panel Main board
communication error
Panel core Main core
communication error
An error is detected at the
F12X
Scan control section
An error is detected at the
F13X
Panel control section
An error is detected at the
F14X
FAX control section
An error is detected at the
F15X authentication device control
section
An error is detected at the
F17X
print data control section
An error is detected at the
F18X
Video control secion
An error is detected at the
F1CX File System management
section
An error is detected at the
F1DX Image memory management
section
Y116520-3
Check procedure & check point
1) Check connection of the harness (Panel to Main board), (Main board to HDD)
and connectors and check function.
2) Check contact of the DDR memory by detaching and reattaching. and check
function. replace it if available and check function.
3) Format the HDD and check function. (U024 FULL formatting)
4) Execute the U021Memory initializing to initialize the controller backup memory
and check function.
5) Replace the panel board and check function.
6) Replace the main board and check function.
7) Retrieve the USBLOG and contact the Service Administrative Division.
1) Check connection of the harness (Panel to Main board), (Main board to HDD)
and connectors and check function.
2) Check contact of the DDR memory by detaching and reattaching. and check
function. replace it if available and check function.
3) Format the HDD and check function. (U024 FULL formatting)
4) Execute the U021 Memory initializing to initialize the controller backup memory
and check function.
5) Replace the main board and check function.
6) Replace the Panel board and check function.
7) Retrieve the USBLOG and contact the Service Administrative Division.
1) Check connection of the harness (Scan/DP - Main board) and connectors and
check function.
2) Format the HDD and check function. (U024 FULL formatting)
3) Execute the U021 Memory initializing to initialize the controller backup memory
and check function.
4) Replace the Scan/DP board and check function.
5) Replace the main board and check function.
6) Retrieve the USBLOG and contact the Service Administrative Division.
1) Check connection of the harness (Panel - Main board) and connectors and
check function.
2) Format the HDD and check function. (U024 FULL formatting)
3) Execute the U021 Memory initializing to initialize the controller backup memory
and check function.
4) Replace the panel board and check function.
5) Replace the main board and check function.
6) Retrieve the USBLOG and contact the Service Administrative Division.
1) Check connection of the harness (FAX - Main board) and connectors and check
function.
2) Format the HDD and check function. (U024 FULL formatting)
3) Execute the U021 Memory initializing to initialize the controller backup memory
and check function.
4) Execute the U671 Clear FAX back up data (FAX DIMM clear) and check
function. (Take cae of the received data since it is cleared)
5) Replace the FAX_DIMM and check function.
6) Replace the FAX board and check function.
7) Replace the main board and check function.
8) Retrieve the USBLOG and contact the Service Administrative Division.
1) Check connection of the harness (Authentication device - Main board) and
connectors and check function.
2) Format the HDD and check function. (U024 FULL formatting)
3) Execute the U021 Memory initializing to initialize the controller backup memory
and check function.
4) Replace the main board and check function.
5) Replace the HDD and check function.
6) Retrieve the USBLOG and contact the Service Administrative Division.
1) Format the HDD and check function. (U024 FULL formatting)
2) Execute the U021 Memory initializing to initialize the controller backup memory
and check function.
3) Replace the main board and check function.
4) Replace the HDD and check function.
5) Retrieve the USBLOG and contact the Service Administrative Division.
1) Check connection of the harness (Engine - Main board) and connectors and
check function.
2) Format the HDD and check function. (U024 FULL formatting)
3) Execute the U021 Memory initializing to initialize the controller backup memory
and check function.
4) Replace the engine board and check function.
5) Replace the main board and check function.
6) Retrieve the USBLOG and contact the Service Administrative Division.
1) Format the HDD and check function. (U024 FULL formatting)
2) Execute the U021 Memory initializing to initialize the controller backup memory
and check function.
3) Replace the main board and check function.
4) Replace the HDD and check function.
5) Retrieve the USBLOG and contact the Service Administrative Division.
1) Format the HDD and check function. (U024 FULL formatting)
2) Execute the U021 Memory initializing to initialize the controller backup memory
and check function.
3) Replace the main board and check function.
4) Replace the HDD and check function.
5) Retrieve the USBLOG and contact the Service Administrative Division.
1-4-155
Remark 1
*User data and installed
software is deleted if
executing the U024.
Reinstallation is required.
[Main-Panel Interface]
Main board:YC12
Panel board:YC10
[Main-Scan Interface]
Main board: YC11,YC25
ISC board: YC3,YC4
[Main-DP relay Interface]
(Check if the boards are firmly
connected via the board-to-
board connector.)
Main board:YC10
DP relay board:YC22
[Main-Panel Interface]
Main board:YC6,YC12
Panel board:YC10,YC17
[Main-KUIO Interface]
Main board:YC8,YC9
KUIO board:YC3,YC4
Authentication device: Card [Main Interface]
Reader, etc. Main board: YC21,YC22,YC26
-
[Main ENGINE Interface]
Main board:YC43
Engine board:YC46 or YC50
*The F1C4 error appears
with the HDD security kit at -
work.
*The F1D4 error is RAM
allocation error.
1Check it with the U340 -
2Initialize the setting
valued with the U021
Service Manual
2N8/2N7-4
Remark 2