Olivetti d-Copia 6500MF Plus Service Manual page 484

No. Content Check procedure & check point
F21X
1) Check contact of the DDR memory and check function.
2) Format the HDD and check function. (U024 FULL formatting)
F22X
3) Execute the U021 Memory initializing to initialize the controller backup memory
An error is detected at the
and check function.
Image processing section
4) Replace the main board and check function.
5) Replace the HDD and check function.
F23X
6) Retrieve the USBLOG and contact the Service Administrative Division.
1) Check contact of the DDR memory and check function.
2) Format the HDD and check function. (U024 FULL formatting)
3) Execute the U021 Memory initializing to initialize the controller backup memory
An error is detected at the
F24X and check function.
System management section
4) Replace the main board and check function.
5) Replace the HDD and check function.
6) Retrieve the USBLOG and contact the Service Administrative Division.
1) Format the HDD and check function. (U024 FULL formatting)
2) Execute the U021 Memory initializing to initialize the controller backup memory
An error is detected at the and check function.
F25X
Network management section 3) Replace the main board and check function.
4) Retrieve the USBLOG and contact the Service Administratuve Division.
(or retrieve the packet capture data depending on the reult of analysis)
F26X
1) Format the HDD and check function. (U024 FULL formatting)
2) Execute the U021 Memory initializing to initialize the controller backup memory
F27X
An error is detected at the and check function.
F28X
System management section 3) Replace the main board and check function.
F29X
4) Replace the HDD and check function.
5) Retrieve the USBLOG and contact the Service Administrative Division.
F2AX
1) Check connection of the harness (Scan/DP board - main board) and connectors
and check function.
2) Format the HDD and check function. (U024 FULL formatting)
An error is detected at the 3) Execute the U021 Memory initializing to initialize the controller backup memory
F33X
Scan management section and check function.
4) Replace the Scan/DP board and check function.
5) Replace the main board and check function.
6) Retrieve the USBLOG and contact the Service Administrative Division.
1) Format the HDD and check function. (U024 FULL formatting)
2) Execute the U021 Memory initializing to initialize the controller backup memory
An error is detected at the and check function.
F34X
Panel management section 3) Replace the main board and check function.
4) Retrieve the USBLOG and contact the Service Administrative Division.
1) Format the HDD and check function. (U024 FULL formatting)
2) Execute the U021 Memory initializing to initialize the controller backup memory
An error is detected at the and check function.
F35X
Print control section 3) Replace the main board and check function.
4) Replace the HDD and check function.
5) Retrieve the USBLOG and contact the Service Administrative Division.
1) Format the HDD and check function. (U024 FULL formatting)
2) Execute the U021 Memory initializing to initialize the controller backup memory
An error is detected at the and check function.
F36X
Print management section 3) Replace the main board and check function.
4) Replace the HDD and check function.
5) Retrieve the USBLOG and contact the Service Administrative Division.
1) Format the HDD and check function. (U024 FULL formatting)
2) Execute the U021 Memory initializing to initialize the controller backup memory
and check function.
3) Execute the U671 Clear FAX back up data (FAX DIMM clear) and check
An error is detected at the function.
F37X
FAX management section
4) Replace the FAX_DIMM and check function.
5) Replace the main board and check function.
6) Replace the HDD and check function.
7) Retrieve the USBLOG and contact the Service Administrative Division.
1) Format the HDD and check function. (U024 FULL formatting)
2) Execute the U021 Memory initializing to initialize the controller backup memory
An error is detected at the
and check function.
F38X Authentication/permit
3) Replace the main board and check function.
management section
4) Replace the HDD and check function.
5) Retrieve the USBLOG and contact the Service Administrative Division.
F3AX
F3BX
F3CX
1) Format the HDD and check function. (U024 FULL formatting)
F3DX
2) Execute the U021 Memory initializing to initialize the controller backup memory
F3EX
F3FX An error is detected at the and check function.
F40X Entity management section 3) Replace the main board and check function.
F41X 4) Replace the HDD and check function.
F42X
5) Retrieve the USBLOG and contact the Service Administrative Division.
F43X
F44X
F45X
Service Manual
(Take cae of the received data since it is cleared)
1-4-156
Remark 1
[DDR2 memory contact check]
Main board:YS1 or YS3
A certain part of the memory be
faulty. The frequency of faiure
occurrence is dependent on the
frequency of access to the
faulty bit. The ASIC may be
faulty if the memory is not
sensitive.
[DDR2 memory contact check]
Main board:YS1 or YS3
*The F248 eror is printer A certain part of the memory be
process error. if it repeats faulty. The frequency of failure
with a certain print data, occurrence is dependent on the
retrieve the capture data and frequency of access to the
USBLOG. faulty bit. The ASIC may be
faulty if the memory is not
sensitive.
*This may be owing to the
-
users network environment.
-
[
Main board: YC11,YC25
ISC board: YC3,YC4
[Main-DP relay Interface]
(Check if the boards are firmly
connected via the board-to-
board connector.)
Main board:YC10
DP relay board:YC22
[Main-Panel Interface]
Main board:YC6,YC12
Panel board:YC10,YC17
-
-
[FAX DIMM contact check]
Main board: YC5
-
-
2N8/2N7-4
Remark 2
]
Y116520-