Siemens Sinumerik 840D sl Function Manual page 365

10/15
11415
MD number
Default value: 0x8
Change becomes effective after: POWER ON
Data type: DWORD
Meaning:
Special cases, errors,...
© Siemens AG 2015 All Rights Reserved
SINUMERIK 840D sl/SINAMICS S120 SINUMERIK Safety Integrated (FBSI sl) - - 10.2015 Edition
$MN_SUPPRESS_ALARM_MASK_2
Suppress alarm outputs
Min. input limit: - -
Protection level: 7/2
Screen form for suppressing special alarm outputs.
Bit set: corresponding alarm (warning) is not initiated.
Bit hex. Meaning
Value
=====================================================================
0: 0x1 16773 "Channel %1 Axis %3 is following axis. The axis/spindle locks of the leading
axes are different"
1: 0x2 2100 "NCK battery warning level reached"
2101 "NCK battery alarm"
2102 "NCK battery alarm"
2: 0x4 2120 "NCK fan alarm" (ineffective on modules which do not require a fan by design)
3: 0x8 15120 "PowerFail: Show buffer overflow"
4: 0x10 15187 "Error during execution of PROGEVENT file"
5: 0x20 15188 "Error during execution of ASUB file"
6: 0x40 26120 "$AA_ESR_ENABLE = 1 and axis is to become neutral"
26121 "Axis is neutral and $AA_ESR_ENABLE =1 is to be set"
26123 "$AA_ESR_ENABLE = 1 is to be set, but $MA_ESR_REACTION is not set"
26124 "$AC_TRIGGER triggered, but axis is neutral, ESR ignores this axis"
7: 0x80 10724 "Software limit violated at start of block"
10734 "Operating range limit violated at start of block"
10737 "Work (WCS) operating range limit violated at start of block"
8: 0x100 14008 "WRITE command in /_N_EXT_DIR"
10734 "Operating range limit violated at start of block"
10737 "Work (WCS) operating range limit violated at start of block"
9: 0x200 14006 "Invalid program name"
10: 0x400 4006 "Maximum number of axes that can be activated exceeded"
11: 0x800 16017 "LIFTFAST ignores this axis, as it cannot be used for the current axis
type"
12: 0x1000 22025 "Channel %1 Block %2 Following axis/spindle %3 Synchronism (2): Fine
tolerance exceeded"
- - Exception: The alarm is generated if for the following axis/spindle involved,
CPMALARM[FAx] Bit 8 = 0 is programmed.
22026 "Channel %1 Block %2 Following axis/spindle %3 Synchronism (2): Coarse
tolerance exceeded"
- - Exception: The alarm is generated if for the following axis/spindle involved,
CPMALARM[FAx] Bit 9 = 0 is programmed.
13: 0x2000 22001 "Braking ramp longer than Stop D time."
22002 "Braking ramp longer than Stop D time with gear stage %3 Reason %4."
14: 0x4000 16963 "ASUB start refused."
15: 0x8000 21751,"Limit velocity %2 deg/min on modulo axis %1 exceeded (defective cam
output)"
21752,"Axis %1 minimum cam width cam %3 undershot at curr. velocity %2"
16: 0x10000 17212 "Channel %1 tool management: Load manual tool %3, duplo no.%2 to
the spindle/toolholder"
17214 "Channel %1 tool management: Remove manual tool %3 from spindle / tool holder
%2"
17215 "Channel %1 tool management: Unload manual tool %3 from buffer location %2"
17216 "Channel %1 unload manual tool from toolholder %4 and load manual tool %3 %2"
17: 0x20000 16771 "Channel %1 Block %3 Following axis %2 overlaid movement not
enabled"
8.1 Machine data for SINUMERIK 840D sl
Max. input limit: - -
Data Description
Unit: - -
8-365