Binector Output Parameters - Siemens SINAMICS G120 Manual

Parameters
Connector/Binector (BICO)-Parameters
p20118[0...1]
p20123[0...1]
p20128
p20133
p20218[0...1]
p20223[0...1]
p20228
p20236
p20244[0...1]
p20250[0...1]
p20256[0...1]
p20266
p20275
p20284
p20308[0...3]
p20312[0...1]
p20318[0...1]
p20372
p20378
p31023[0...3]
p31026[0...2]
1.4.3

Binector Output Parameters

Product: SINAMICS G120, Version: 4402100, Language: eng, Type: BO
r0751.0...10
r0785.0...1
r0807.0
r1025.0
r2043.0...2
r2090.0...15
r2091.0...15
r2092.0...15
r2093.0...15
r2094.0...15
r2095.0...15
r8413.0...1
r8423.0...1
r8433.0...1
r9935.0
r20031
r20035
r20039
r20043
r20047
r20051
r20055
r20059
r20063
r20067
r20071
r20075
1-484
CI: DIV 0 inputs / DIV 0 inputs
CI: DIV 1 inputs / DIV 1 inputs
CI: AVA 0 input X / AVA 0 input X
CI: AVA 1 input X / AVA 1 input X
CI: NSW 0 inputs / NSW 0 inputs
CI: NSW 1 inputs / NSW 1 inputs
CI: LIM 0 input X / LIM 0 input X
CI: LIM 1 input X / LIM 1 input X
CI: PT1 0 inputs / PT1 0 inputs
CI: PT1 1 inputs / PT1 1 inputs
CI: INT 0 inputs / INT 0 inputs
CI: LVM 0 input X / LVM 0 input X
CI: LVM 1 input X / LVM 1 input X
CI: DIF 0 input X / DIF 0 input X
CI: ADD 2 inputs / ADD 2 inputs
CI: NCM 0 inputs / NCM 0 inputs
CI: NCM 1 inputs / NCM 1 inputs
CI: PLI 0 input X / PLI 0 input X
CI: PLI 1 input X / PLI 1 input X
CI: Multi-zone control setpoint input / Zone_ctrl setp inp
CI: Multi-zone control actual-value input / Zon_ctrl act inp
BO: CU analog inputs status word / CU AI status word
BO: CU analog outputs status word / CU AO ZSW
BO: Master control active / PcCtrl active
BO: Fixed speed setpoint status / n_setp_fix status
BO: PROFIdrive PZD state / PD PZD state
BO: PROFIdrive PZD1 receive bit-serial / PZD1 recv bitw
BO: PROFIdrive PZD2 receive bit-serial / PZD2 recv bitw
BO: PROFIdrive PZD3 receive bit-serial / PZD3 recv bitw
BO: PROFIdrive PZD4 receive bit-serial / PZD4 recv bitw
BO: Connector-binector converter binector output / Con/bin outp
BO: Connector-binector converter binector output / Con/bin outp
BO: RTC DTC1 output / RTC DTC1 output
BO: RTC DTC2 output / RTC DTC2 output
BO: RTC DTC3 output / RTC DTC3 output
BO: POWER ON delay signal / POWER ON t_delay
BO: AND 0 output Q / AND 0 output Q
BO: AND 1 output Q / AND 1 output Q
BO: AND 2 output Q / AND 2 output Q
BO: AND 3 output Q / AND 3 output Q
BO: OR 0 output Q / OR 0 output Q
BO: OR 1 output Q / OR 1 output Q
BO: OR 2 output Q / OR 2 output Q
BO: OR 3 output Q / OR 3 output Q
BO: XOR 0 output Q / XOR 0 output Q
BO: XOR 1 output Q / XOR 1 output Q
BO: XOR 2 output Q / XOR 2 output Q
BO: XOR 3 output Q / XOR 3 output Q
SINAMICS G120 Control Units CU230P-2 Parameter Manual (LH9), 01/2011
© Siemens AG 2011 All Rights Reserved