Siemens SINAMICS G120 Manual page 487

p1009[0...n]
p1010[0...n]
p1011[0...n]
p1012[0...n]
p1013[0...n]
p1014[0...n]
p1015[0...n]
r1024
r1045
r1050
r1073
r1077
r1078
p1083[0...n]
r1084
p1086[0...n]
r1087
r1112
r1114
r1119
r1149
r1150
r1169
r1170
r1258
r1298
r1337
r1343
r1348
r1438
r1445
r1454
r1468
r1482
r1490
r1493
r1508
r1516
r1518[0...1]
p1520[0...n]
p1521[0...n]
p1524[0...n]
p1525[0...n]
r1526
r1527
r1538
r1539
r1547[0...1]
r1548[0...1]
p1570[0...n]
r1593[0...1]
r1597
r1598
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU230P-2 Parameter Manual (LH9), 01/2011
CO: Fixed speed setpoint 9 / n_set_fixed 9
CO: Fixed speed setpoint 10 / n_set_fixed 10
CO: Fixed speed setpoint 11 / n_set_fixed 11
CO: Fixed speed setpoint 12 / n_set_fixed 12
CO: Fixed speed setpoint 13 / n_set_fixed 13
CO: Fixed speed setpoint 14 / n_set_fixed 14
CO: Fixed speed setpoint 15 / n_set_fixed 15
CO: Fixed speed setpoint effective / n_set_fixed eff
CO: Mot. potentiometer speed setp. in front of ramp-fct. gen. / Mop n_set bef RFG
CO: Motor. potentiometer setpoint after the ramp-function generator / Mop setp after RFG
CO: Main setpoint effective / Main setpoint eff
CO: Supplementary setpoint effective / Suppl setpoint eff
CO: Total setpoint effective / Total setpoint eff
CO: Speed limit in positive direction of rotation / n_limit pos
CO: Speed limit positive effective / n_limit pos eff
CO: Speed limit in negative direction of rotation / n_limit neg
CO: Speed limit negative effective / n_limit neg eff
CO: Speed setpoint after minimum limiting / n_set n. min_lim
CO: Setpoint after the direction limiting / Setp after limit
CO: Ramp-function generator setpoint at the input / RFG setp at inp
CO: Ramp-function generator, acceleration / RFG acceleration
CO: Ramp-function generator speed setpoint at the output / RFG n_set at outp
CO: Speed controller, speed setpoints 1 and 2 / n_ctrl n_set 1/2
CO: Speed controller, setpoint sum / n_ctrl setp sum
CO: Vdc controller output / Vdc_ctrl output
CO: Vdc controller output (U/f) / Vdc_ctrl output
CO: Actual slip compensation / Slip comp act val
CO: I_max controller frequency output / I_max_ctrl f_outp
CO: U/f control Eco factor actual value / U/f Eco fac act v
CO: Speed controller, speed setpoint / n_ctrl n_set
CO: Actual speed smoothed / n_act smooth
CO: Speed controller system deviation I component / n_ctrl sys dev Tn
CO: Speed controller P-gain effective / n_ctr Kp eff
CO: Speed controller I torque output / n_ctrl I-M_output
CO: Droop feedback speed reduction / Droop n_reduction
CO: Moment of inertia, total / M_inertia total
CO: Torque setpoint before supplementary torque / M_set bef. M_suppl
CO: Supplementary torque and acceleration torque / M_suppl + M_accel
CO: Accelerating torque / M_accel
CO: Torque limit upper / M_max upper
CO: Torque limit lower / M_max lower
CO: Torque limit upper/motoring scaling / M_max up/mot scal
CO: Torque limit lower scaling / M_max lower scal
CO: Torque limit upper without offset / M_max up w/o offs
CO: Torque limit lower without offset / M_max low w/o offs
CO: Upper effective torque limit / M_max upper eff
CO: Lower effective torque limit / M_max lower eff
CO: Torque limit for speed controller output / M_max outp n_ctrl
CO: Stall current limit torque-generating maximum / Isq_max stall
CO: Flux setpoint / Flux setpoint
CO: Field weakening controller / flux controller output / Field/Fl_ctrl outp
CO: Field weakening controller output / Field_ctrl outp
CO: Total flux setpoint / Flux setp total
Connector/Binector (BICO)-Parameters
Parameters
1-487