Connector/Binector (Bico)-Parameters - Siemens SINAMICS G120 Manual

p2082[0...15]
p2083[0...15]
p2084[0...15]
p2103[0...n]
p2104[0...n]
p2105[0...n]
p2106[0...n]
p2107[0...n]
p2108[0...n]
p2112[0...n]
p2116[0...n]
p2117[0...n]
p2144[0...n]
p2148[0...n]
p2200[0...n]
p2220[0...n]
p2221[0...n]
p2222[0...n]
p2223[0...n]
p2235[0...n]
p2236[0...n]
p2286[0...n]
p3111[0...n]
p3112[0...n]
p3232[0...n]
p3330[0...n]
p3331[0...n]
p3332[0...n]
p3880
p3883
p8785
p8786
p8787
p11000
p11100
p11200
p20030[0...3]
p20034[0...3]
p20038[0...3]
p20042[0...3]
p20046[0...3]
p20050[0...3]
p20054[0...3]
p20058[0...3]
p20062[0...3]
p20066[0...3]
p20070[0...3]
p20074[0...3]
p20078
p20082
p20086
p20090
p20138
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU230P-2 Parameter Manual (LH9), 01/2011
BI: Binector-connector converter status word 3 / Bin/con ZSW3
BI: Binector-connector converter status word 4 / Bin/con ZSW4
BI: Binector-connector converter status word 5 / Bin/con ZSW5
BI: 1. Acknowledge faults / 1. Acknowledge
BI: 2. Acknowledge faults / 2. Acknowledge
BI: 3. Acknowledge faults / 3. Acknowledge
BI: External fault 1 / External fault 1
BI: External fault 2 / External fault 2
BI: External fault 3 / External fault 3
BI: External alarm 1 / External alarm 1
BI: External alarm 2 / External alarm 2
BI: External alarm 3 / External alarm 3
BI: Motor stall monitoring enable (negated) / Mot stall enab neg
BI: RFG active / RFG active
BI: Technology controller enable / Tec_ctrl enable
BI: Technology controller fixed value selection bit 0 / Tec_ctrl sel bit 0
BI: Technology controller fixed value selection bit 1 / Tec_ctrl sel bit 1
BI: Technology controller fixed value selection bit 2 / Tec_ctrl sel bit 2
BI: Technology controller fixed value selection bit 3 / Tec_ctrl sel bit 3
BI: Technology controller motorized potentiometer raise setpoint / Tec_ctrl mop raise
BI: Technology controller motorized potentiometer lower setpoint / Tec_ctrl mop lower
BI: Hold technology controller integrator / Tec_ctr integ stop
BI: External fault 3, enable / Ext fault 3 enab
BI: External fault 3 enable negated / Ext flt 3 enab neg
BI: Load monitoring failure detection / Load_moni fail_det
BI: 2-3-WIRE Control Command 1 / 2-3-WIRE CC_1
BI: 2-3-WIRE Control Command 2 / 2-3-WIRE CC_2
BI: 2-3-WIRE Control Command 3 / 2-3-WIRE CC_3
BI: ESM activation / ESM activation
BI: ESM direc. rot. / ESM direc. rot.
BI: CAN status word bit 8 / Status word bit 8
BI: CAN status word bit 14 / Status word bit 14
BI: CAN status word bit 15 / Status word bit 15
BI: Free tec_ctrl 0 enable / Ftec0 enab
BI: Free tec_ctrl 1 enable / Ftec1 enab
BI: Free tec_ctrl 2 enable / Ftec2 enab
BI: AND 0 inputs / AND 0 inputs
BI: AND 1 inputs / AND 1 inputs
BI: AND 2 inputs / AND 2 inputs
BI: AND 3 inputs / AND 3 inputs
BI: OR 0 inputs / OR 0 inputs
BI: OR 1 inputs / OR 1 inputs
BI: OR 2 inputs / OR 2 inputs
BI: OR 3 inputs / OR 3 inputs
BI: XOR 0 inputs / XOR 0 inputs
BI: XOR 1 inputs / XOR 1 inputs
BI: XOR 2 inputs / XOR 2 inputs
BI: XOR 3 inputs / XOR 3 inputs
BI: NOT 0 input I / NOT 0 input I
BI: NOT 1 input I / NOT 1 input I
BI: NOT 2 input I / NOT 2 input I
BI: NOT 3 input I / NOT 3 input I
BI: MFP 0 input pulse I / MFP 0 inp_pulse I

Connector/Binector (BICO)-Parameters

Parameters
1-481