Siemens SINAMICS G120 Manual page 553

r0899
ZSW seq_ctrl
[2503.7]
r0899 .0
r0899
[2503.7] ZSW seq_ctrl
r0899 .1
r0899
ZSW seq_ctrl
[2503.7]
r0899 .2
r2139
[2548.7] ZSW fault/alarm 1
.3
r2139
r0899
[2503.7] ZSW seq_ctrl
r0899 .4
r0899
[2503.7] ZSW seq_ctrl
r0899 .5
r0899
[2503.7] ZSW seq_ctrl
r0899 .6
r2139
[2548.7] ZSW fault/alarm 1
r2139
.7
r2197
[2534.7] ZSW monitor 1
r2197 .7
r0899
[2503.7] ZSW seq_ctrl
r0899 .7
r2197
[2534.7] ZSW monitor 1
r2197 .6
r0056
[2526.7] ZSW cl-loop ctrl
r0056 .13
r2135
[2548.7] ZSW fault/alarm 2
r2135 .14
r2197
[2534.7] ZSW monitor 1
r2197 .3
r2135
[2548.7] ZSW fault/alarm 2
r2135 .15
r0052.3 displays status bit r2139.3 or r1214.10, if p1210 > 0
<1>
1 2
Internal control/status words
Status word 1
Bit No. Status word 1 (r0052)
1 = Drive ready for switching on
0
0 = Drive not ready for switching on
1 = Drive ready for operation (DC link loaded, pulses disabled)
1
0 = Drive not ready for operation
1 = Drive running (voltage at output terminals)
2
0 = Pulses disabled
1 = Fault present (pulses disabled)
3
0 = No fault
0 = Coast down active (OFF2 active)
4
1 = No coast down active (OFF2 inactive)
0 = Fast stop active (OFF3 active)
5
1 = No fast stop active (OFF3 inactive)
1 = Switching on inhibited active
6
0 = No switching on inhibited (possible to switch on)
1 = Alarm present
7
0 = No alarm
0 = Deviation setpoint / actual speed
8
1 = No deviation setpoint / actual speed
9
1 = Control request (always 1)
1 = Maximum speed reached (f_act >= p1082 (f_max))
10
0 = f_act < p1082 (f_max)
0 = I,M,P limit reached
11
1 = Limit not reached
Reserved
12
0 = Alarm motor overtemperature
13
1 = No motor overtemperature
1 = Motor rotates forwards
14
0 = Motor does not rotate forwards
0 = Alarm drive converter overload
15
1 = No drive converter overload
3 4
ZSW 1
r0052
r0052
r0052.0
r0052.1
r0052.2
Signal "Fault active" is inverted if connected
<1> r0052.3 to a digital output which means that the
relay will be in the de-energised state.
r0052.4
r0052.5
r0052.6
r0052.7
r0052.8
r0052.9
r0052.10
r0052.11
r0052.13
r0052.14
r0052.15
5 6
Function diagram
FP_2510_97_01.vsd
G120 CU230P-2
13.12.2010 V4.4
7 8
- 2510 -