Binector Output Parameters - Siemens CU230P-2 HVAC Parameter Manual

Parameters
Connector/Binector (BICO)-Parameters
1.4.3

Binector Output Parameters

Product: SINAMICS G120, Version: 4301300, Language: eng, Type: BO
r0751.0...10
r0785.0...1
r0807.0
r1025.0
r2043.0...2
r2090.0...15
r2091.0...15
r2092.0...15
r2093.0...15
r2094.0...15
r2095.0...15
r8413.0...1
r8423.0...1
r8433.0...1
r9935.0
r20031
r20035
r20039
r20043
r20047
r20051
r20055
r20059
r20063
r20067
r20071
r20075
r20079
r20083
r20087
r20091
r20120
r20125
r20130
r20135
r20140
r20145
r20150
r20155
r20160
r20165
r20170
r20175
r20180
r20185
r20189
r20190
r20194
r20195
r20199
1-424
BO: CU analog inputs status word / CU AI status word
BO: CU analog outputs status word / CU AO status word
BO: Master control active / PcCtrl active
BO: Fixed frequency status / f_fixed status
BO: PROFIdrive PZD state / PD PZD state
BO: PROFIdrive PZD1 receive bit-serial / PZD1 recv bitw
BO: PROFIdrive PZD2 receive bit-serial / PZD2 recv bitw
BO: PROFIdrive PZD3 receive bit-serial / PZD3 recv bitw
BO: PROFIdrive PZD4 receive bit-serial / PZD4 recv bitw
BO: Connector-binector converter binector output / Con/bin outp
BO: Connector-binector converter binector output / Con/bin outp
BO: RTC DTC1 output / RTC DTC1 output
BO: RTC DTC2 output / RTC DTC2 output
BO: RTC DTC3 output / RTC DTC3 output
BO: POWER ON delay signal / POWER ON t_delay
BO: AND 0 output Q / AND 0 output Q
BO: AND 1 output Q / AND 1 output Q
BO: AND 2 output Q / AND 2 output Q
BO: AND 3 output Q / AND 3 output Q
BO: OR 0 output Q / OR 0 output Q
BO: OR 1 output Q / OR 1 output Q
BO: OR 2 output Q / OR 2 output Q
BO: OR 3 output Q / OR 3 output Q
BO: XOR 0 output Q / XOR 0 output Q
BO: XOR 1 output Q / XOR 1 output Q
BO: XOR 2 output Q / XOR 2 output Q
BO: XOR 3 output Q / XOR 3 output Q
BO: NOT 0 inverted output / NOT 0 inv output
BO: NOT 1 inverted output / NOT 1 inv output
BO: NOT 2 inverted output / NOT 2 inv output
BO: NOT 3 inverted output / NOT 3 inv output
BO: DIV 0 divisor is zero QF / DIV 0 divisor=0 QF
BO: DIV 1 divisor is zero QF / DIV 1 divisor=0 QF
BO: AVA 0 input negative SN / AVA 0 input neg SN
BO: AVA 1 input negative SN / AVA 1 input neg SN
BO: MFP 0 output Q / MFP 0 output Q
BO: MFP 1 output Q / MFP 1 output Q
BO: PCL 0 output Q / PCL 0 output Q
BO: PCL 1 output Q / PCL 1 output Q
BO: PDE 0 output Q / PDE 0 output Q
BO: PDE 1 output Q / PDE 1 output Q
BO: PDF 0 output Q / PDF 0 output Q
BO: PDF 1 output Q / PDF 1 output Q
BO: PST 0 output Q / PST 0 output Q
BO: PST 1 output Q / PST 1 output Q
BO: RSR 0 output Q / RSR 0 output Q
BO: RSR 0 inverted output QN / RSR 0 inv outp QN
BO: RSR 1 output Q / RSR 1 output Q
BO: RSR 1 inverted output QN / RSR 1 inv outp QN
BO: DFR 0 output Q / DFR 0 output Q
SINAMICS G120 Control Units CU230P-2 Parameter Manual (LH9), 11/2009
© Siemens AG 2009 All Rights Reserved