Siemens SINAMICS G120 Manual page 474

Parameters
Command and Drive Data Sets – Overview
p1345[0...n]
p1346[0...n]
p1349[0...n]
p1350[0...n]
p1400[0...n]
p1401[0...n]
p1402[0...n]
p1416[0...n]
p1452[0...n]
p1456[0...n]
p1457[0...n]
p1458[0...n]
p1459[0...n]
p1461[0...n]
p1463[0...n]
p1464[0...n]
p1465[0...n]
p1470[0...n]
p1472[0...n]
p1487[0...n]
p1488[0...n]
p1489[0...n]
p1496[0...n]
p1499[0...n]
p1514[0...n]
p1517[0...n]
p1520[0...n]
p1521[0...n]
p1524[0...n]
p1525[0...n]
p1530[0...n]
p1531[0...n]
p1570[0...n]
p1573[0...n]
p1574[0...n]
p1580[0...n]
p1582[0...n]
p1584[0...n]
p1594[0...n]
p1596[0...n]
p1610[0...n]
p1611[0...n]
p1616[0...n]
p1654[0...n]
p1702[0...n]
p1703[0...n]
p1715[0...n]
p1717[0...n]
p1726[0...n]
p1727[0...n]
p1730[0...n]
p1740[0...n]
p1745[0...n]
1-474
I_max voltage controller proportional gain / I_max_U_ctrl Kp
I_max voltage controller integral time / I_max_U_ctrl Tn
U/f mode resonance damping maximum frequency / Uf res_damp f_max
Soft starting / Soft starting
Speed control configuration / n_ctrl config
Flux control configuration / Flux ctrl config
Closed-loop current control and motor model configuration / I_ctrl config
Speed setpoint filter 1 time constant / n_set_filt 1 T
Speed controller speed actual value smoothing time (SLVC) / n_C n_act T_s SLVC
Speed controller P gain adaptation lower starting point / n_ctrl AdaptKpLow
Speed controller P gain adaptation upper starting point / n_ctrl AdaptKp up
Adaptation factor, lower / Adapt_factor lower
Adaptation factor, upper / Adapt_factor upper
Speed controller Kp adaptation speed, upper scaling / n_ctrl Kp n upper
Speed controller Tn adaptation speed, upper scaling / n_ctrl Tn n upper
Speed controller adaptation speed, lower / n_ctrl n lower
Speed controller adaptation speed, upper / n_ctrl n upper
Speed controller encoderless operation P-gain / n_ctrl SLVC Kp
Speed controller encoderless operation integral time / n_ctrl SLVC Tn
Droop compensation torque scaling / Droop M_comp scal
Droop input source / Droop input source
Droop feedback scaling / Droop scaling
Acceleration pre-control scaling / a_before scaling
Accelerating for torque control, scaling / a for M_ctrl scal
Supplementary torque 2 scaling / M_suppl 2 scal
Accelerating torque smoothing time constant / M_accel T_smooth
CO: Torque limit upper / M_max upper
CO: Torque limit lower / M_max lower
CO: Torque limit upper/motoring scaling / M_max up/mot scal
CO: Torque limit lower scaling / M_max lower scal
Power limit motoring / P_max mot
Power limit regenerative / P_max gen
CO: Flux setpoint / Flux setpoint
Flux threshold value magnetizing / Flux thresh magnet
Voltage reserve dynamic / U_reserve dyn
Efficiency optimization / Efficiency opt.
Flux setpoint smoothing time / Flux setp T_smth
Field weakening operation, flux setpoint smoothing time / Field weak T_smth
Field-weakening controller, P gain / Field_ctrl Kp
Field weakening controller integral-action time / Field_ctrl Tn
Torque setpoint static (SLVC) / M_set static
Supplementary accelerating torque (SLVC) / M_suppl_accel
Current setpoint smoothing time / I_set T_smooth
Curr. setpoint torque-gen. smoothing time field weakening range / Isq_s T_smth FW
Isd current controller pre-control scaling / Isd_ctr_prectrScal
Isq current controller pre-control scaling / Isq_ctr_prectrScal
Current controller P gain / I_ctrl Kp
Current controller integral-action time / I_ctrl Tn
Quadrature arm decoupling, scaling / Transv_decpl scal
Quadrature arm decoupling at voltage limit scaling / TrnsvDecplVmaxScal
Isd controller integral component shutdown threshold / Isd_ctrl I_thresh
Gain resonance damping for encoderless closed-loop control / Gain res_damp
Motor model error threshold stall detection / MotMod ThreshStall
SINAMICS G120 Control Units CU230P-2 Parameter Manual (LH9), 01/2011
© Siemens AG 2011 All Rights Reserved