Cadillac 60 Series 1963 Shop Manual page 600

INDEX
Subject
Page No.
Subject
Page No.
Hydra-Matic Transmission (Cont'd.)
Principles of Operation 6-1
Rear Unit Sun Gear End Play
Checking 6-34
Service Information 6-4
Torus Cover and Flywheel Leak Test. 6-47
Towing Instructions 6-14
SECTION 7
PROPELLER SHAFT AND REAR AXLE
Propeller Shaft and Rear Axle
Controlled Differential 7-2
Differential Carrier, Removal and
Installation 7-10
General Description 7-1
Propeller Shaft:
Bearing, Center, Removal and
Installation 7-13
Propeller Shafts, Front and Rear,
Disassembly and Assembly . . . . 7-12
Removal and Installation 7-10
Slip Yoke, Front, Leak Test 7-11
Universal Joints, Standard,
Removal and Installation 7-11
Rear Axle:
Axle Shaft Removal and
Installation (Comm'l. Chassis) . . 7-9
Axle Shaft, Bearing Oil Seal, and
Wheel Bearing Removal and
Installation (Except Comm'l.
Chassis) 7-6
Backlash Measurement 7-6
Gear Ratio Identification 7-3
Oil Seal Replacement (Comm'l.
Chassis). 7-9
Pinion Flange and Oil Seal,
Removal and Installation (60 and
62 series) 7-3
Pinion Yoke and Oil Seal, Removal
and Installation (75 series and
Comm'l. Chassis) 7-5
Rear Wheel and Brake Drum
Removal and Installation 7-6
Special Tools 7-15
Specifications 7-16
Torque Specifications 7-14
SECTION 8
POWER BRAKES
Brakes (Cont'd.)
Bendix Power Brake Unit,
Disassembly, Cleaning, Inspection
and Assembly 8-11
Bleeding Brakes. 8-8
Brake Drums, Machining . . . . . . . . 8-6
Brake Shoe Assemblies 8-4
Brake Shoes, Manual Adjustment . . . 8-3
Brake System Testing 8-22
Delco Moraine Master Cylinder,
Disassembly, Cleaning, Inspection
and Assembly 8-20
Delco Moraine Power Brake Unit,
Disassembly, Cleaning, Inspection
and Assembly 8-17
Diagnosis Chart 8-23
General Description 8-1
Hose, Brake, Hydraulic Service . . . . 8-9
Linings, New, Break-In 8-7
Parking Brake Assembly:
Adjustment 8-3
Diaphragm, Removal and
Installation 8-11
Preliminary Checks 8-9
Removal and Installation 8-10
Power Brake Unit, Removal and
Installation 8-11
Relining Brakes 8-4
Special Tools 8-27
Specifications 8-26
Stoplight Switch, Removal, Installation
and Adjustment 8-8
Torque Specifications 8-27
Wheel Cylinder:
Assembly and Installation 8-7
Removal, Disassembly and Cleaning . 8-7
Brakes
Bendix Master Cylinder, Disassembly,
Cleaning, Inspection and Assembly .
5-15
SECTION 9
ENGINE, MECHANICAL
Engine Mechanical
Camshaft:
Checking 9-30
Installation < 9-30
Removal 9-30
Camshaft Bearing, Removal and
Installation 9-31
Connecting Rod:
Alignment 9-27
Installation 9-27
Removal 9-24
Connecting Rod Bearing Replacement . 9-24
Crankshaft,Removal and Installation . . 9-33