Cadillac 60 Series 1963 Shop Manual page 210

ENGINE MECHANICAL
9-17
8. Install rocker arm assembly, with four at-
taching screws, in position on cylinder head with
oil grooves in rocker arm shaft facing downward,
and oil holes in shaft toward center of engine. Top
of push rods must be seated in rocker arm
sockets.
CAUTION: Make sure thinner end of rocker
shaft brackets are right side up or the rocker
shaft may be sprung out of alignment when the
cap screws are tightened down.
9. Tighten all cylinder head cap screws to
75 foot-pounds, starting from center row and
working outward and toward each end.
10. Install exhaust pipe on exhaust manifolds,
using new gaskets, and secure with attaching
screws. Tighten cap screws to 33 foot-pounds.
CAUTION: Be sure face of manifold heat
valve stamped " T O P " is next to left manifold.
11. Apply a coat of gasket cement to both sides
of new intake manifold gaskets, and install gaskets
in position over locating dowels.
12. Install intake manifold with carburetor on
cylinder heads, being sure manifold is positioned
correctly over locating dowels.
13. Install two front corner cap screws and
four nuts with washers that hold intake manifold
to cylinder heads.
14. Install throttle return spring bracket with
spring on left rear corner of intake manifold,
and heater hose bracket on right rear corner,
and install remaining two rear corner screws
that secure intake manifold to cylinder heads.
15. Tighten four cap screws to 30 foot-pounds,
and four nuts to 25 foot-pounds.
16. Install fuel line between carburetor and
fuel filter.
17. Connect small ventilator valve hose to fit-
ting on carburetor insulator and secure with hose
clamp.
18. Connect throttle control linkage to carbu-
retor throttle lever and secure linkage with throt-
tle return spring.
19. Connect transmission TV rod to carburetor
throttle lever.
20. Adjust throttle control linkage and TV rod
as described in Section 10, Note 26c.
21. Connect throttle return valve vacuum hose
and parking brake vacuum hose to fitting on rear
of intake manifold.
NOTE: If car is equipped with vacuum door
locks, connect vacuum door lock hose on same
fitting.
22. Connect power brake vacuum hose to fitting
on carburetor.
23. Connect distributor primary wire to nega-
tive terminal on ignition coil, and ignition resistor
wire to positive terminal.
24. Connect idle speed-up control vacuum line
at control unit, if car is equipped with Air
Conditioner.
25. Connect vacuum advance line to vacuum
advance unit on distributor.
26. Install rocker arm covers, secondary wir-
ing, and distributor cap as an assembly, using
new gaskets. Install rocker arm cover attaching
screws and tighten to 28 inch-pounds.
27. Install distributor cap on distributor and
connect high voltage wire to ignition coil.
28. Connect spark plug wires at plugs, and
connect spark plug wire retainer clip to retainer
bracket on carburetor.
29. Lubricate new water outlet pipe to water
pump O-ring seal with silicone, and install O-ring
against shoulder in bore in pump body.
30. Brush gasket cement on water outlet pipe
flange surfaces and place new gaskets in position
on water outlet pipe.
31. Install neck of water outlet pipe in bore in
pump body and position flange surfaces against
cylinder heads. Install three (of the four) attach-
ing screws, and tighten screws- to 20 foot-pounds.
Do not install screw that holds generator support
bracket at this time.
NOTE: On cars equipped with Air Con-
ditioner, install all four cap screws that hold
water outlet pipe to cylinder heads.
32. Connect heater inlet hose to water outlet
pipe and upper radiator hose to thermostat
housing.
33. Install oil filter assembly on oil filter sup-
port bracket, using new gasket, and secure with
three attaching screws. Tighten screws to 10
foot-pounds.
34. Install generator support bracket on cylin-
der head water outlet pipe and secure with two
attaching screws. Tighten screws to 20 foot-
pounds.
35. Connect, at cowl, ground strap from rear
of cylinder head.