Cadillac 60 Series 1963 Shop Manual page 531

16-62
BODY
4. Remove screws securing rear quarter filler
panel to quarter panel and remove filler panel,
5. Using a trim panel removing tool, J-6335,
carefully pry trim assembly retaining nails from
tacking strip; then lift trim assembly upward to
disengage from retainers at top of rear quarter
inner panel and remove assembly from body.
6. To install rear quarter trim assembly, re-
verse removal procedures.
NOTE: If any retaining nails are broken off,
they can be replaced with door trim assembly
nailing strip replacement tabs which are avail-
able as a service part.
b. Removal and Installation—67 Styles
1. Remove folding top compartment side trim
panel assembly.
2. On styles with manually-operated windows,
remove window regulator handle and anti-friction
washer.
3. Using a trim panel removing tool carefully
pry trim assembly retaining nails from tacking
strips; then lift assembly upward to disengage
from retainers at top of rear quarter inner panel
and remove assembly from body.
4. To install rear quarter trim assembly, re-
verse removal procedure.
NOTE: If any retaining nails are broken off,
they can be replaced with door trim assembly
nailing strip replacement tabs which are avail-
able as a service part.
c. Lower Trim Assembly Removal and
Installation—29, 39 and 89 Styles
1. Remove rear seat cushion and seat back.
2. Remove back window side garnish molding
and side roof rail rear finishing molding. On 29
styles remove rear quarter window front garnish
molding.
3. Using a trim panel removing tool, J-6335,
carefully pry trim assembly retaining nails from
tacking strip; then lift trim assembly upward to
disengage from retainers at top of rear quarter
inner panel and remove assembly from quarter
panel.
4. To install rear quarter trim assembly, re-
verse removal procedure.
d. Upper Trim Assembly
Removal and Installation—29 Styles
1. Remove back window side garnish molding
and side roof rail rear finishing molding.
2. Carefully break cement bond securing trim
foundation to roof extension inner panel; then re-
move trim assembly.
3. To install, first apply trim cement to con-
tacting surfaces of trim foundation and roof ex-
tension inner panel. Position trim and press or
roll to assure a good cement bond. Install back
window side garnish molding and side roof rail
rear finishing molding.
e. Upper Trim Assembly
Removal and Installation—
6239, 6339, 6257, 6357, 6389 Styles
1. Remove back window side garnish molding
and side roof rail rear finishing molding, where
present.
2. On styles with courtesy lamps in the upper
trim assembly, remove courtesy lamp lens and
two screws securing reflector and remove lamp
assembly.
3. Carefully insert a trim panel removing tool
or other suitable tool between headlining and up-
per edge of upper trim assembly. Disengage
upper trim assembly retaining clips from roof
extension inner panel by pulling inboard at clip
locations. Remove trim assembly from body.
4. To install, reverse removal procedure.
71. Rear Quarter Window Assembly
Manual or Electric
a. Removal and Installation—57 Styles
1. Remove rear seat cushion and seat back as-
semblies and rear quarter arm rest and trim
assemblies. Remove inner panel access hole
cover.
NOTE: On models equipped with electric
window regulators, disconnect feed wire con-
nector from electric motor.
CAUTION: Do not operate regulator motor
after window assembly is disengaged from the
regulator. Operation of motor with the load re-
moved may damage unit.
2. Remove rear quarter window rear guide at-
taching screws, Fig. 16-71. Disengage rear guide
from roller on window lower sash channel and re-
move guide.
3. With the rear quarter window in the half-
down position, remove lower sash channel cam
attaching screws, Fig. 16-71. Detach cam from
roller on regulator arm and remove cam.
4. Mark (scribe) position of window lower stop
on front guide to enable reinstalling stop in same