Cadillac 60 Series 1963 Shop Manual page 502

BODY
16-33
2. Drill a 1/4 inch hole through back plate and
sector at location indicated at either A, B, or C,
depending on position of lift arm.
NOTE: Do not drill into motor housing, part
of which is indicated in Fig. 16-36 by dotted
line. In addition, locate hole a sufficient dis-
tance from edge of sector to insure proper
retention of sector.
3. Insert 3/16 inch bolt through hole in back
plate and sector and install nut to bolt. Do not
tighten nut.
4. Remove motor attaching bolts and remove
motor assembly from regulator, Fig. 16-36.
NOTE: Clean off steel chips from regulator
sector and motor pinion gear.
5. To install, reverse removal procedure. If
difficulty is encountered when trying to line up
motor attaching holes, regulator lift arm may be
moved up or down manually so that motor pinion
gear will mesh with teeth on regulator sector and
regulator attaching holes will line up.
NOTE: Be sure to remove temporary nut
and bolt from regulator before installing it in
door.
34. Front Door Window Assembly-
Manual and Electric
Except 23 and 33 Styles
a. Removal and Installation
1. Raise door window. Remove door trim as-
sembly and detach inner panel water deflector.
2. Through holes in inner panel, remove screw
securing window assembly front and rear stops
to lower window sash channel. Then lower window
slightly and remove stops, Fig. 16-34.
3. Lower door window to expose window lower
sash channel cam attaching screws. Then on
styles equipped with electric window regulators,
disconnect wiring harness feed wire from regu-
lator motor at connector.
NOTE: It may be necessary to loosen ven-
tilator frame and tilt it forward to facilitate
removal of door window.
4. Remove window lower sash channel cam
attaching screws and disengage cam from window
sash channel. Then lift window assembly upward
and remove from door.
CAUTION: Do not operate regulator motor
after window assembly is disengaged from reg-
ulator. Operation of motor with load removed
may damage unit.
5. To install, reverse removal procedure. Be-
fore installing window lower sash channel cam,
lubricate entire length of cam. Check window for
proper operation prior to installing inner panel
water deflector and door trim pad.
b. Adjustments
The door window glass may be adjusted to pro-
vide proper contact with side roof rail weather-
strip. Adjustments have also been provided to
relieve a binding door glass due to misalignment
of glass run channels. To perform the following
adjustments, remove door trim assembly and
detach inner panel water deflector, where neces-
sary, to gain access to hardware attaching points;
then proceed as follows:
1. To correct a condition where glass is cocked
in glass run channels, loosen inner panel cam
attaching screws, adjust cam up or down as re-
quired and retighten screws, Fig. 16-34.
2. To adjust upper front portion of window
assembly in or out for proper contact with side
roof rail weatherstrip, adjust ventilator assembly
in or out as described in Note 32.
3. To adjust lower portion of ventilator division
channel for alignment with window assembly,
lower door window and loosen ventilator division
channel adjusting stud nut. Turn adjusting stud in
or out or position lower end of channel fore or
aft, as required; then, retighten adjusting stud nut,
Fig. 16-35.
4. To adjust upper rear of window assembly in
or out for proper contact with side roof rail
weatherstrip, or to adjust rear of window assem-
bly in or out at belt line, loosen rear glass run
channel attaching screws at lock pillar facing of
door and screw at top of door inner panel. Posi-
tion channel in or out as required and tighten
screws, Fig. 16-27.
NOTE: Adjustments 2, 3 and 4 must be co-
ordinated to provide a properly operating, front
door window.
5. To adjust limit of "up" travel of window
assembly for proper contact with side roof rail
weatherstrip, raise door window and through inner
panel access holes loosen door window front and
rear stop assembly attaching bolts. Adjust stops
up or down as required, then tighten attaching
bolts, Fig. 16-34.
35. Front Door Inner Panel
Cam Assembly
a. Removal and Installation
1. Raise door window. Remove door trim as-
sembly and detach inner panel water deflector.