Cadillac 60 Series 1963 Shop Manual page 532

BODY
16-63
Front Guide ^
Upper Adjusting
W
.
i n d
A
°
w
Regulator
Stud and Nuts
L
j
f A r m S t o
J ^
:;
Window
Regulator
Attaching
Screws
r Guide
Attaching Screws
• I . -
Sash Channel Cam
Attaching Screws
At ' ' .
Front Guide Lower
Adjusting Stud and Nut .
r/
Fig. 16-71 Rear Quarter Hardware - 57 Styles
position. Loosen window lower stop attaching
screw and slide stop to bottom of guide.
5. Lower window to run lower roller on win-
dow sash channel frame out of front guide
channel at the bottom.
6. Lift window upward and inboard to disengage
upper roller on window sash channel from rear
channel on front guide. Remove window assembly
from body.
7. To install, reverse removal procedure.
Prior to installation, lubricate channel of window
lower sash channel cam. Seal all hardware at-
tachments that have been disturbed. Refer to
Note 75.
b. Adjustments—57 Styles
1. Remove rear seat cushion and seat back as-
semblies. Remove rear quarter arm rest and trim
assemblies.
2. To adjust window fore or aft, loosen front
and rear guide attaching stud nuts, Fig. 16-71.
Position the window and guides fore or aft as r e -
quired; then tighten attaching stud nuts.
3. To adjust rear quarter window in or out,
loosen the front guide upper attaching stud nuts,
Fig. 16-71. Adjust studs in or out as required,
then tighten stud nuts.
4. To adjust top of the rear quarter window in
or out, loosen front guide lower attaching stud nut,
Fig. 16-71. Adjust stud in or out as required, then
tighten stud nut.
5. To relieve a binding condition between chan-
nels of front and rear guide, loosen front and rear
guide adjusting stud nuts, Fig. 16-71. Operate
window to full up position and tighten upper stud
nuts on front guide and forward attaching screw on
rear guide. Operate window to full down and
tighten remaining nuts.
6. To limit forward and upward travel of rear
quarter window, adjust regulator lift arm stop as
required, Fig. 16-71.
7. To limit down travel of rear quarter window,
remove inner panel large access hole cover,
loosen lower stop assembly attaching bolt (located
at lower end of window front guide cam) and adjust
stop up or down as required.
NOTE: After performing window adjust-
ments, seal hardware attaching screws which
have been disturbed. Refer to Note 75.
c. Removal and Installation—67 Styles
1. Lower folding top and operate rear quarter
window to half down position. Remove rear seat
cushion and seat back. Remove folding top com-
partment side trim panel and rear quarter trim
assembly.
2. On styles equipped with electric window r e -
gulators, remove access hole cover and discon-
nect wiring harness electrical feed plug from
regulator motor.
CAUTION: Do not operate regulator motor
after window is disengaged from regulator.
Operation of motor with load removed may
damage unit.
3. Remove window pivot bolt, Fig. 16-72. Dis-
engage window male hinge from female hinge
plate; then raise window to disconnect window
lower sash channel cam from roller on window
regulator lift arm and remove window.
Window Pivot Hinge
Attaching Bolt
^ / 'f M ill
Window Guide Upper
Attaching Nuts
Window Pivot Hinge
Adjusting Studs
Window Regulator
Attaching Screws
^ Window Guide
V Cenrer Attaching
\ Nut *
V N
Window Guide
Lower Attaching Screw
Fig. 16-72 Rear Quarter Hardware - 67 Styles