Cadillac 60 Series 1963 Shop Manual page 533

16-64
BODY
4. To install rear quarter window assembly,
reverse removal procedure. Prior to installation,
lubricate pivot hinge and window lower sash chan-
nel cam.
Adjust rear quarter window for proper align-
ment and operation, as described below. Seal
window pivot bolt and inner panel access hole
cover, as specified in Note 75.
d. Adjustments—67 Styles
1. To adjust the limit of rear quarter window
up travel, loosen the window guide upper attach-
ing screws, Fig. 16-72, then adjust upper stop to
desired position and tighten guide attaching
screws.
2. To adjust rear quarter window up or down or
fore or aft, or to adjust the top or rear of window
in or out, the folding top compartment side trim
panel and rear quarter trim assembly must be r e -
moved to gain access to the pivot bolt and adjust-
ing studs.
a. Up or down or fore or aft window adjustment:
loosen pivot bolt and both adjusting stud nuts, Fig.
16-72. Position window as required; then tighten
pivot bolt and stud nuts.
b. In or out adjustment of top of window: loosen
lower adjusting stud nuts and slightly loosen rear
stud nut. Adjust lower stud in or out, as required;
then tighten both stud nuts, Fig. 16-72.
c. In or out adjustment of rear of window:
loosen pivot hinge rear adjusting stud nut and
(slightly) lower adjusting stud nut. Loosen window
guide upper attaching nuts and center stud nut,
Fig. 16-72. Adjust rear adjusting stud in or out,
as required, then tighten both stud nuts. Adjust
window guide for proper alignment with window
and tighten upper attaching nuts and center stud
nut.
NOTE: After performing any rear quarter
window adjustment, seal all attaching screws
which have been disturbed. Refer to Note 75.
e. Removal and Installation—29 Styles
1. Remove rear seat cushion and seat back. Re-
move back window side garnish molding and rear
quarter window front garnish molding. Remove
rear quarter lower trim assembly.
2. Remove screws securing three glass rubber
channel retainers at bottom of window and retainer
at top of window. Using a suitable tool, carefully
break sealer bond between rubber channel and
body opening.
3. Carefully push rear quarter glass and rub-
ber channel assembly inward and remove as-
sembly from opening.
Rear Quarter Window And
Rubber Channel Assembly
Fig. 16-73 Rear Quarter Window Sealing
NOTE: The rear quarter window rubber
channel may be removed from the glass as a
bench operation.
4. To install, reverse removal procedure.
Prior to installing quarter window glass and rub-
ber channel, clean off old sealer from rubber
channel and body opening to insure a smooth
sealing surface. Apply a ribbon of medium-bodied
sealer in corner of rear quarter side outer panel
rabbet, 1 in Fig. 16-73, completely around window
opening. After glass and rubber channel have been
installed, apply a bead of weatherstrip cement be-
tween outer surface of the glass and rubber
channel, 2 in Fig. 16-73, completely around the
window and rubber channel. Clean off excess
sealer and cement.
72. Rear Quarter Window Regulator
Assembly—Manual or Electric
a. Removal and Installation—57 Styles
1. Remove rear quarter window.
NOTE: On styles equipped with electric win-
dow regulators, disconnect feed wire plug from
electric motor.
CAUTION: Do not operate regulator motor
after the window assembly is disengaged from
regulator or after regulator assembly is r e -
moved from the body. Operation of the motor
with load removed may damage the unit.
2. Remove rear quarter window regulator at-
taching screws, Fig. 16-71, then remove regulator
assembly through large access hole.
3. To install, reverse removal procedure. Seal
all hardware attaching locations that have been
disturbed as specified in Note 75.