Proxim ORiNOCO AP-800 Installation And Management Manual page 62

3.5.2.1 Authentication Attributes
•
User-Name: Specifies the name of the user that needs to be authenticated. It must be sent in Access-Request
packets, if available.
•
User-Password: Specifies the user password to be authenticated, or the user's input following an Access-Challenge.
It is only used in Access-Request packets.
•
NAS-IP-Address: Specifies the identifying IP Address of the NAS (AP) which is requesting authentication of the user,
and should be unique to the NAS (AP) within the scope of the RADIUS server. NAS-IP-Address is only used in
Access-Request packets.
•
State: Specifies the attribute sent by the server to the client in an Access-Challenge and must be sent unmodified
from the client to the server in the new Access-Request reply to that challenge, if any.
•
Class: Specifies the attribute sent by the server to the client in an Access-Accept and should be sent unmodified by
the client to the accounting server as part of the Accounting-Request packet if accounting is supported.
•
Session-Time-out: Specifies the attribute that sets the maximum number of seconds of service to be provided to the
user before termination of the session or prompt. This Attribute is available to be sent by the server to the client in an
Access-Accept or Access-Challenge.
•
Termination-Action: Specifies the action taken by the NAS (AP) when the specified service is completed. It is only
used in Access-Accept packets.
•
Called-Station-Id: Specifies the MAC address of the AP wireless interface with which the client gets authenticated.
•
Calling-Station-Id: Specifies the MAC address of the client being authenticated.
•
Acct-Interim-Interval: Specifies the attribute obtained during the Authentication process and used for determining
the time interval for sending Accounting Update messages.
: If this attribute is not obtained from the RADIUS Server, the AP uses default value of 300 seconds for updating
the accounting messages.
3.5.2.2 Accounting Attributes
•
Acct-Status-Type: Specifies whether this Accounting-Request marks the beginning of the user service (Start) or the
end (Stop).
•
Acct-Input-Octets: Specifies the number of octets that have been received from the port over the course of this
service being provided, and can only be present in Accounting-Request records where the Acct-Status-Type is set to
Stop.
•
Acct-Output-Octets: Specifies the number of octets that have been sent to the port in the course of delivering this
service, and can only be present in Accounting-Request records where the Acct-Status-Type is set to Stop.
•
Acct-Session-Id: Specifies a unique Accounting ID to make it easy to match start and stop records in a log file. The
start and stop record for a given session will have the same Acct-Session-Id.
•
Acct-Authentic: Specifies an attribute that is included in an Accounting-Request to indicate how the user was
authenticated, whether by RADIUS, the NAS itself, or another remote authentication protocol.
•
Acct-Session-Time: Specifies the total time in seconds, the user has received service for, and can only be present in
Accounting-Request records where the Acct-Status-Type is set to Stop.
•
Acct-Input-Packets: Specifies the number of packets that have been received from the port over the course of this
service being provided to a Framed User, and can only be present in Accounting-Request records where the
Acct-Status-Type is set to Stop.
•
Acct-Output-Packets: Specifies the number of packets that have been sent to the port in the course of delivering this
service to a framed user, and can only be present in Accounting-Request records where the Acct-Status-Type is set to
Stop.
•
Acct-Terminate-Cause: Specifies the cause for which the session was terminated, and can only be present in
Accounting- Request records where the Acct-Status-Type is set to Stop.
ORiNOCO® AP-800 and AP-8000 Installation and Management Guide
Device Configuration Using Web Interface
62