Proxim ORiNOCO AP-800 Installation And Management Manual page 151

: Status is not applicable to the first VAP on an interface, as it is always enabled.
To configure VAP in WDS mode, enter the following CLI commands:
: Same CLI configuration applies to the VAP(s) enabled in WDS-Legacy mode and to the VAP(s) on the interface 2.
ORiNOCO® AP-800 and AP-8000 Installation and Management Guide
AP-00:7D:09>enable
AP-00:7D:09# configure
AP-00:7D:09(config)# wireless
AP-00:7D:09(config-wireless)# vap
AP-00:7D:09(config-wireless-vap)# index 1
AP-00:7D:09(config-wireless-vap)# index 1 secondary-index 1 broadcast-ssid
enable
AP-00:7D:09(config-wireless-vap)# index 1 secondary-index 1 fragmentation
2339
AP-00:7D:09(config-wireless-vap)# index 1 secondary-index 1 macacl-status
enable
AP-00:7D:09(config-wireless-vap)# index 1 secondary-index 1 max-stations
12
AP-00:7D:09(config-wireless-vap)# index 1 secondary-index 1
multicast-legacy-rate 4
AP-00:7D:09(config-wireless-vap)# index 1 secondary-index 1 qos-name
Default
AP-00:7D:09(config-wireless-vap)# index 1 secondary-index 1
radius-acc-status enable
AP-00:7D:09(config-wireless-vap)# index 1 secondary-index 1
radius-macacl-status disable
AP-00:7D:09(config-wireless-vap)# index 1 secondary-index 1
security-profile-index 1
AP-00:7D:09(config-wireless-vap)# index 1 secondary-index 1
radius-profile-index 1
AP-00:7D:09(config-wireless-vap)# index 1 secondary-index 1 ssid test
AP-00:7D:09(config-wireless-vap)# index 1 secondary-index 1 vlan-id 2
AP-00:7D:09(config-wireless-vap)# index 1 secondary-index 1 vlan-priority
2
AP-00:7D:09(config-wireless-vap)# index 1 secondary-index 1 status enable
AP-00:7D:09(config-wireless-vap)# index 1 secondary-index 1 type ?
Possible completions:
<ap(1)/wds(3)/wds-end-a(9)/wds-end-b(10)>
AP-00:7D:09(config-wireless-vap)# index 1 secondary-index 1 type wds-end-a
AP-00:7D:09(config-wireless-vap)# index 1 secondary-index 1 wds-peer
00:02:6f:59:27:06
AP-00:7D:09(config-wireless-vap)# exit
AP-00:7D:09(config-wireless)# exit
AP-00:7D:09# show wireless vap
// VAP CONFIGURATION //
INTERFACE 1.1
Status
Vap Type
Vap SSID
Vap BSSID
Broadcast SSID
Multicast Legacy Rate
Supported Multicast Legacy Rate : 2,4,11,22,12,18,24,36,48,72,96,108
Fragmentation Threshold
Security Profile Index
Security Profile Name
Radius Profile Index
Radius Profile Name
VLAN ID
Vlan Priority
Qos Profile Name
MAC-ACL Status
Radius MAC-ACL Status
Radius Accounting Status
WDS Peer MAC Address
Maximum Stations
Device Configuration, Management and Monitoring using CLI
Vap Type Configuration
: enable
: wds-end-a
: test
: 62:02:6f:5b:6b:2c
: enable
: 4
: 2339
: 1
: AP Security
: 1
: Default Radius
: 2
: 2
: Default
: disable
: disable
: enable
: 00:02:6f:59:27:06
: 12
151