Renesas M16C FAMILY series Hardware Manual page 68

M 1 6 C 2 / 8 G o r u p ( M 1 6 C
Oscillation Stop Detection Register
b7 b6 b5 b4 b3
0 0
NOTES:
1. Write to this register after setting the PRC0 bit in the PRCR register to "1" (write enable).
2. When the CM20 bit is "1" (oscillation stop, re-oscillation detection function enabled), the CM27 bit is set to
"1" (oscillation stop, re-oscillation detection interrupt), and the CPU clock source is the main clock, the
CM21 bit is automatically set to "1" (on-chip oscillator clock) if the main clock stop is detected.
3. If the CM20 bit is set to "1" and the CM23 bit is set to "1" (main clock not oscillating), do not set the CM21
bit to "0".
4. This flag is set to "1" when the main clock is detected to have stopped or when the main clock is detected
to have restarted oscillating. When this flag changes state from "0" to "1", an oscillation stop, reoscillation
restart detection interrupt is generated. Use this flag in an interrupt routine to discriminate the causes of
interrupts between the oscillation stop, reoscillation detection interrupts and the watchdog timer interrupt.
The flag is cleared to "0" by writing a "0" by program. (Writing a "1" has no effect. Nor is it cleared to "0" by
an oscillation stop or an oscillation restart detection interrupt request acknowledged.)
If when the CM22 bit is set to "1" an oscillation stoppage or an oscillation restart is detected, no oscillation
stop, reoscillation restart detection interrupts are generated.
5. Read the CM23 bit in an oscillation stop, re-oscillation detection interrupt handling routine to determine the
main clock status.
6. Effective when the CM07 bit in the CM0 register is set to "0".
7. When the PM21 bit in the PM2 register is "1" (clock modification disabled), writing to the CM20 bit has no
effect.
8. When the CM20 bit is set to "1" (oscillation stop, re-oscillation detection function enabled), the CM27 bit is
set "1" (oscillation stop, re-oscillation detection interrupt), and the CM11 bit is "1" (the CPU clock source is
PLL clock), the CM21 bit remains unchanged even when main clock stop is detected. If the CM22 bit is set
to "0" under these conditions, oscillation stop, re-oscillation detection interrupt occur at main clock stop
detection; it is, therefore, necessary to set the CM21 bit to "1" (on-chip oscillator clock) inside the interrupt
routine.
9. Set the CM20 bit to "0" (disable) before entering stop mode. After exiting stop mode, set the CM20 bit back
to "1" (enable).
10. Set the CM20 bit to "0" (disable) before setting the CM05 bit in the CM0 register.
11. The CM20, CM21 and CM27 bits do not change at oscillation stop detection reset.
12. When the CM21 bit is set to "0" (on-chip oscillator turned off) and the CM05 bit is set to "1" (main clock
turned off), the CM06 bit is fixed to "1" (divide-by-8 mode) and the CM15 bit is fixed to "1" (drive capability
High).
Figure 7.5 CM2 Register
R e . v 2 0 . 0 J a . n 3 , 1 2 0 0 7
R E J 0 9 B 0 0 4 7 0 - 2 0 0
2 / , 8 M 1 6 C 2 / 8 ) B
b2 b1 b0
Symbol
CM2
Bit Symbol
Oscillation stop, re-
CM20
oscillation detection bit
(7, 9, 10, 11)
System clock select bit 2
CM21
(2, 3, 6, 8, 11, 12 )
Oscillation stop, re-
CM22
oscillation detection flag
(4)
X
CM23
(5)
Reserved bit
(b5-b4)
Nothing is assigned. When write, set to "0". When read, its
(b6)
content is indeterminate.
Operation select bit
CM27
(when an oscillation stop,
re-oscillation is detected)
(11)
page 48
f o 3 8 5
(1)
Address
000C
16
Bit Name
0: Oscillation stop, re-oscillation
detection function disabled
1: Oscillation stop, re-oscillation
detection function enabled
0: Main clock or PLL clock
1: On-chip oscillator clock
(On-chip oscillator oscillating)
0: "Oscillation stop, re-oscillation"
not detected
1: "Oscillation stop, re-oscillation"
detected
0: Main clock oscillating
monitor flag
IN
1: Main clock not oscillating
Set to "0"
0: Oscillation stop detection reset
1: Oscillation stop, re-oscillation
detection interrupt
7. Clock Generation Circuit
After Reset
2 (11)
0X000010
Function
RW
RW
RW
RW
RO
RW
RW