Renesas M16C FAMILY series Hardware Manual page 260

M 1 6 C 2 / 8 G o r u p ( M 1 6 C
A/D Control Register 0
b7
NOTES:
A/D Control Register 1
b7
NOTES:
1. If the ADCON1 register is rewritten during A/D conversion, the conversion result will be indeterminate.
2.AN0
bits in the ADCON2 register to select the desired pin.
3.If the VCUT bit is reset from "0" (Vref unconnected) to "1" (Vref connected), wait for 1 µs or more before starting
A/D conversion.
A/D Control Register 2
b7
NOTES:
1. If the ADCON2 register is rewritten during A/D conversion, the conversion result will be indeterminate.
2. Set to "1" in delayed trigger mode 0.
Figure 15.22 ADCON0 to ADCON2 Registers in Delayed Trigger Mode 0
R e . v 2 0 . 0 J a . n 3 , 1 2 0 0 7
R E J 0 9 B 0 0 4 7 0 - 2 0 0
2 / , 8 M 1 6 C 2 / 8 ) B
(1)
b6 b5 b4 b3 b2 b1 b0
Symbol
0 0 0 1 1 1
ADCON0
Bit Symbol
CH0
CH1
CH2
MD0
MD1
TRG
ADST
CKS0
1. If the ADCON0 register is rewritten during A/D conversion, the conversion result will be indeterminate.
2. Do not write "1" in delayed trigger mode 0. When write, set to "0".
(1)
b6 b5 b4 b3 b2 b1 b0
Symbol
1 0
ADCON1
Bit Symbol
SCAN0
SCAN1
MD2
BITS
CKS1
VCUT
(b7-b6)
to AN0 and AN2 to AN2 can be used in the same way as AN
0 7 0 7
(1)
b6 b5 b4 b3 b2 b1 b0
Symbol
0 0 1
ADCON2
Bit Symbol
SMP
ADGSEL0
ADGSEL1
(b3)
CKS2
TRG1
(b7-b6)
page 240
f o 3 8 5
Address After Reset
03D6 00000XXX
16
Bit Name
b2 b1 b0
Analog Input Pin
1 1 1 : Set to "111b" in delayed trigger
Select Bit
mode 0
b4 b3
A/D Operation Mode
0 0 : One-shot mode or delayed trigger mode
Select Bit 0
0,1
Trigger Select Bit Refer to Table 15.11
A/D Conversion Start 0 : A/D conversion disabled
(2) 1 : A/D conversion started
Flag
Refer to Table 15.2
Frequency Select Bit 0
Address After Reset
03D7 00
16 16
Bit Name
A/D Sweep Pin
When selecting delayed trigger sweep mode 0
(2)
Select Bit
b1 b0
0 0: AN to AN
0
0 1: AN to AN
0
1 0: AN to AN
0
1 1: AN to AN
0
A/D Operation Mode
0 : Any mode other than repeat sweep
Select Bit 1
mode 1
8/10-Bit Mode Select Bit 0 : 8-bit mode
1 : 10-bit mode
Refer to Table 15.2
Frequency Select Bit 1
(3)
Vref Connect Bit 1 : Vref connected
Nothing is assigned. When write, set to "0".
When read, its content is "0".
to AN . Use the ADGSEL1 to ADGSEL0
0 7
Address After Reset
03D4 00
16 16
Bit Name
A/D Conversion Method
1 : With sample and hold
(2)
Select Bit
b2 b1
A/D Input Group
0 0 : Select port P10 group
Select Bit
0 1 : Do not set
1 0 : Select port P0 group
1 1 : Select port P1/P9 group
Reserved Bit "0"
Set to
Frequency Select Bit 2
Refer to Table 15.2
Trigger Select Bit 1
Refer to Table 15.11
Nothing is assigned. When write, set to "0".
When read, its content is "0".
2
Function RW
RW
RW
RW
RW
RW
RW
RW
RW
Function
RW
RW
(2 pins)
1
(4 pins)
3
(6 pins)
5
RW
(8 pins)
7
RW
RW
RW
RW
Function RW
RW
RW
RW
RW
RW
RW
15. A/D Converter