Renesas M16C FAMILY series Hardware Manual page 144

M 1 6 C 2 / 8 G o r u p ( M 1 6 C
Three-phase PWM Control Register 0
b7 b6 b5 b4 b3 b2 b1 b0
NOTES:
1. Write to this register after setting the PRC1 bit in the PRCR register to "1" (write enable). Note also that INV00 to
INV02, INV04 and INV06 bits can only be rewritten when timers A1, A2, A4 and B2 are idle.
2. If this bit needs to be set to "1", set any value in the ICTB2 register before writing to it.
3. Effective when the INV11 bit is "1" (three-phase mode 1). If INV11 is set to "0" (three-phase mode 0), the ICTB2
counter is incremented by "1" each time the timer B2 underflows, regardless of whether the INV00 and INV01 bits are
set. When setting the INV01 bit to "1", the first interrupt is generated when the timer B2 underflows n-1 times, if n is
the value set in the ICTB2 counter. Subsequent interrupts are generated every n times the timer B2 underflow.
4. Setting the INV02 bit to "1" activates the dead time timer, U/V/W-phase output control circuits and ICTB2 counter.
5. When the INV02 bit is set to "1" and the INV03 bit is set to "0", U, U, V, V, W, W pins, including pins shared with
other output functions, enter a high-impedance state. When INV03 is set to "1", U/V/W corresponding pins generate
the three-phase PWM output.
6. The INV03 bit is set to "0" in the following cases:
• When reset
• When positive and negative go active (INV05="1") simultaneously while INV04 bit is "1"
• When set to "0" by program
• When input on the SD pin changes state from "H" to "L" regardless of the value of the INVCR1 bit. (The INV03 bit
cannot be set to "1" when SD input is "L".)
INV03 is set to "0" when both INV04 bit and INV05 bit are set to "1".
7. Can only be set by writing "0" by program, and cannot be set to "1".
8. The effects of the INV06 bit are described in the table below.
Mode
Timing at which transferred from IDB0 to
IDB1 registers to three-phase output shift
register
Timing at which dead time timer trigger is
generated when INV16 bit is "0"
INV13 bit
Transfer trigger: Timer B2 underflow, write to the INV07 bit or write to the TB2 register when INV10 is "1"
9: If the INV06 bit is set to "1", set the INV11 bit to "0" (three-phase mode 0) and set the PWCON bit to "0" (timer B2
reloaded by a timer B2 underflow).
Figure 12.26 INVC0 Register
R e . v 2 0 . 0 J a . n 3 , 1 2 0 0 7
R E J 0 9 B 0 0 4 7 0 - 2 0 0
2 / , 8 M 1 6 C 2 / 8 ) B
Symbol
INVC0
Bit Symbol
Effective interrupt output
INV00
polarity select bit
Effective interrupt output
specification bit
INV01
Mode select bit
INV02
Output control bit
INV03
Positive and negative
INV04
phases concurrent output
disable bit
Positive and negative
INV05
phases concurrent output
detect flag
Modulation mode select
INV06
bit
INV07 Software trigger select bit
Item
Triangular wave modulation mode
Transferred only once synchronously
with the transfer trigger after writing to
the IDB0 to IDB1 registers
Synchronous with the falling edge of
timer A1, A2, or A4 one-shot pulse
Effective when INV11 is set to "1" and
INV06 is set to "0"
page 124
f o 3 8 5
(1)
Address After Reset
0348 00
16 16
Bit Name
0: ICTB2 counter is incremented by 1 on
the rising edge of timer A1 reload
control signal
1: ICTB2 counter is incremented by 1 on
the falling edge of timer A1 reload
control signal
(3)
0: ICTB2 counter incremented by 1 at a
timer B2 underflow
(2, 3)
1: Selected by INV00 bit
(4)
0: Three-phase motor control timer
function unused
1: Three-phase motor control timer
function
(6)
0: Three-phase motor control timer output
disabled
1: Three-phase motor control timer output
enabled
0: Simultaneous active output enabled
1: Simultaneous active output disabled
0: Not detected yet
1: Already detected
0: Triangular wave modulation mode
1: Sawtooth wave modulation mode
(8)
Setting this bit to "1" generates a transfer
trigger. If the INV06 bit is "1", a trigger for
the dead time timer is also generated.
The value of this bit when read is "0".
INV06=0
Function RW
RW
RW
RW
(5)
(5)
RW
RW
(7)
RW
(9)
RW
RW
INV06=1
Sawtooth wave modulation mode
Transferred every transfer trigger
Synchronous with the transfer
trigger and the falling edge of timer
A1, A2, or A4 one-shot pulse
No effect
12. Timer