Output Block (Analog And Digital) - R&S AFQ100A Operating Manual

R&S AFQ100A

Output Block (analog and digital)

Command
[SOURce:]OUTPut:ANALog<CH>:AMODe
[SOURce:]OUTPut:ANALog<CH>:BALanced:AMPLitude
[SOURce:]OUTPut:ANALog<CH>:BALanced:BIAS
[SOURce]:OUTPut:ANALog<CH>:BALanced:BIAS:STATe
[SOURce:]OUTPut:ANALog<CH>:BALanced:OFFSet:I
[SOURce:]OUTPut:ANALog<CH>:BALanced:OFFSet:Q
[SOURce:]OUTPut:ANALog<CH>:TYPE
[SOURce:]OUTPut:ANALog<CH>:UNBalanced:AMPLitude
[SOURce:]OUTPut:ANALog<CH>:UNBalanced:OFFSet:I
[SOURce:]OUTPut:ANALog<CH>:UNBalanced:OFFSet:Q
[SOURce:]OUTPut:AOUTput
[SOURce:]OUTPut:ANALog<CH>:[BALanced:]AMPLitude
[SOURce:]OUTPut:ANALog<CH>:[BALanced:]BIAS
[SOURce:]OUTPut:ANALog<CH>:[BALanced:]BIAS:STATe
[SOURce:]OUTPut:ANALog<CH>:[BALanced:]OFFSet:I
[SOURce:]OUTPut:ANALog<CH>:[BALanced:]OFFSet:Q
[SOURce:]OUTPut:DIGital<CH>:AMPLitude
[SOURce:]OUTPut:DIGital<CH>:CLOCk:SLOPe
[SOURce:]OUTPut:DIGital<CH>:OFFSet:I
[SOURce:]OUTPut:DIGital<CH>:OFFSet:Q
[SOURce:]OUTPut:DIGital<CH>:PASSignment:I0
[SOURce:]OUTPut:DIGital<CH>:PASSignment:I1
[SOURce:]OUTPut:DIGital<CH>:PASSignment:Q0
[SOURce:]OUTPut:DIGital<CH>:PASSignment:Q1
[SOURce:]OUTPut:DIGital<CH>:PORT
[SOURce:]OUTPut:DIGital<CH>:RESolution
[SOURce:]OUTPut:STATe
Note:
If the instrument is not fitted with either two digital or two analog output boards then omit the <CH>
suffix.
1401.3084.32
AFQ Commands - Signal Generation
Parameters
ELECtronic | ATTenuators
0 ... 1.5 V
-2.5 V ... +2.5 V
ON | OFF
-10 mV ... +10 mV
-10 mV ... +10 mV
Balanced / Unbalanced
0 ... 0.75 V
-10 mV ... +10 mV
-10 mV ... +10 mV
ANALog | DIGital |
ANALOG1 | ANALOG2 |
DIGITAL1 | DIGITAL2
0 V ... 0.75 V
-2.5 V ... +2.5 V
ON | OFF
-10 mV ... +10 mV
-10 mV ... +10 mV
0 FS ... 1 FS
POSitive | NEGative
-0.1 FS ...+0.1 FS, digital
-0.1 FS ...+0.1 FS, digital
SIGNal | MARKer
SIGNal | MARKer
SIGNal | MARKer
SIGNal | MARKer
PORT1 | PORT2
6 Bits ... 16 Bits
ON | OFF
6.56
Default unit Remark
V
V
mV
mV
V
mV
mV
mV
mV
E-3