Setting Item List - KIP 9000 Service Manual

8. 1. 5. 4

Setting item list

Item Setting target
No.
00 Metric or inch
01 Operation of Interface
02 Maximum cut length
03 Trailing margin of long print
04 Special paper size
05 Counting unit of Counter A
06 Counting unit of Counter B
07 Operation of Dehumidify Heater
08 Cut length of user Test Print
09 Standard / Special Setting Value Changing Mode
(PPC)
0A Standard / Special Setting Value Changing Mode
(Tracing paper)
0b Standard / Special Setting Value Changing Mode
(Film)
0C Cold Sleep ON/OFF
0d Compensation of Analog Outputs
0E Reserved
0F Reserved
10 Fusing temperature (PPC)
11 Fusing temperature (Tracing)
12 Fusing temperature (Film)
13 LED strobe time
14 Reserved
15 Pre-Transfer LED / Separation Corona OFF timing
(PPC)
16 Pre-Transfer LED ON / OFF
17 Separation Lamp ON / OFF (PPC)
18 Separation Lamp ON / OFF (Tracing)
19 Developer Bias (applied when Auto Density
Control is set to OFF)
1A Current setting for the Image Corona Wire
1b Current setting for the Grid Plate (applied when
Auto SP Control is set to OFF)
1C Current setting for the Transfer Corona (PPC)
1d Current setting for the Transfer Corona (Tracing)
1E Current setting for the Transfer Corona (Film)
1F Separation Corona DC component (PPC)
20 Separation Corona DC component (Tracing)
21 Separation Corona DC component (Film)
22 Paper Feed Motor speed (Bypass feed)
23 Paper Feed Motor speed (Roll 1)
24 Paper Feed Motor speed (Roll 2)
25 Paper Feed Motor speed (Roll 3)
26 Paper Feed Motor speed (Roll 4)
27 Fuser Motor speed
(Bypass feed / PPC / Large size)
28 Fuser Motor speed
(Bypass feed / PPC / Medium size)
29 Fuser Motor speed
(Bypass feed / PPC / Small size)
2A Fuser Motor speed
(Bypass feed / PPC / Smallest size)
Default Special Adjustable
value setting
NO A0 or 36
NO
NO
NO On or OFF
NO 900/891/880
NO
NO
NO
NO A0 to b5
48 to 8.5
NO
NO
NO
NO On or OFF
NO
NO
NO
OK 150 to 190
OK 150 to 190
OK 150 to 190
NO
NO
NO
NO
NO
NO 000 to 0FF
NO 000 to 0FF
NO 000 to 500
OK 000 to 500
OK 000 to 500
OK 000 to 500
OK 000 to 500
OK 000 to 500
OK 000 to 500
NO -1.0% to 1.0%
NO -1.0% to 1.0%
NO -1.0% to 1.0%
NO -1.0% to 1.0%
NO -1.0% to 1.0%
OK -1.0% to 1.0%
OK -1.0% to 1.0%
OK -1.0% to 1.0%
OK -1.0% to 1.0%
8-39
Unit of Refer
Range setting
value page;
8-46
0 to 2 8-46
6 or 24 m 8-47
8-47
mm 8-48
0 to 3 8-49
0 to 3 8-49
0 or 1 8-50
8-50
0 or 1 8-51
0 or 1 8-51
0 or 1 8-51
8-57
8-57
o
1 C 8-58
o
1 C 8-58
o
1 C 8-58
0 to 42 1 micro- 8-58
sec.
0 or 1 8-59
0 or 1 8-60
0 or 1 8-60
0 or 1 8-61
Hex. 8-62
Hex. 8-62
Hex. 8-63
Hex. 8-63
Hex. 8-63
Hex. 8-63
Hex. 8-64
Hex. 8-64
Hex. 8-64
0.05% 8-64
0.05% 8-64
0.05% 8-64
0.05% 8-64
0.05% 8-64
0.05% 8-65
0.05% 8-65
0.05% 8-65
0.05% 8-65
K115sm8e2.doc
to