KIP 9000 Service Manual page 538

Code Signal name IC Port
18 PFMTR_LD U015 P70
19 TNR_BTL U015 P71
1A FUMTR_LD U015 P72
1b ------- U015 P73
1C DEV_TNR2 U015 P74
1d DEV_TNR1 U015 P75
1E MP_SW U015 P79
1F EXIT_SW U015 P77
20 ------- U015 P80
21 SW_DATA0 U015 P81
22 SW_DATA1 U015 P82
23 SIG_IN U015 P83
24 ------- U015 P84
25 DECK_SW1 U015 P85
26 DECK_SW2 U015 P86
27 DECK_SW3 U015 P87
28 ------- U015 P90
29 ------- U015 P91
2A T_SIZE0 U015 P92
2b DEVE_HP U015 P93
2C PFUT_ST U015 P94
2d T_SIZE1 U015 P95
2E P_SEPR U015 P96
2F P_EXIT U015 P97
30 ------- U015 P50
31 ------- U015 P51
32 IN_CNT_B U015 P52
33 IN_CNT_A U015 P53
NOTES
1. I / O means input signal or output signal.
2. F.C. means Function Checking (Mode).
If the signal is provided with "OK", concerning target (motors, blowers and so on) is operatable
in the Function Checking Mode. (Refer to [8.1.4 Function Checking Mode] on and after the
page 8-32.) If the signal is provided with "NO", it is not operatable.
Connector Signal
J204-9 Paper Feed Motor
Synchronous Signal
J204-10 Toner Remaining Level
Detection Signal
J204-11 Fuser Motor Synchronous
Signal
J204-12
J204-13 Toner Detection Signal 2
(Developer Toner Sensor)
J204-14 Toner Detection Signal 1
(Hopper Toner Sensor)
J204-15 Bypass Feeder Switch
Signal
J204-16 Exit Cover Switch Signal
J203-1
J203-2 Switch Data Signal 0
J203-3 Switch Data Signal 1
J203-4 Reception PCB input Signal
J203-5
J203-6 Roll Deck Switch Signal 1
J203-7 Roll Deck Switch Signal 2
J203-8 Roll Deck Switch Signal 3
J203-9
J203-10
J203-11 Cut Sheet Size Sensor 0
Signal
J203-12 Developer Unit Position
Sensor Signal
J203-13 Internal Transportation Unit
Set Sensor Signal
J203-14 Cut Sheet Size Sensor 1
Signal
J203-15 Separation Sensor Signal
J203-16 Exit Sensor Signal
J205-1
J205-2
J205-3
J205-4
Counter A (Upper) Control
Signal Feed Back
Counter B (Lower) Control
Signal Feed Back
8-13
Condition
Paper Feed Motor (M2) is
rotating when "L".
Toner Remaining Level
Sensor detects "No toner"
when "L". (Receives the light)
Fuser Motor (M5) is rotating
when "L".
Developer Toner Sensor
(TLS2) detects "No toner"
when "L".
Hopper Toner Sensor (TLS1)
detects "No toner" when "L".
Bypass Feeder is open when
"H".
Exit Cover Switch (DS5)
detects door open when "H".
Communicating : Pulse
Not communicating : H
Roll Deck Switch 1 (DS1)
detects "Top Roll Deck open"
when "H".
Roll Deck Switch 2 (DS2)
detects "Middle Roll Deck
open" when "H".
Roll Deck Switch 3 (DS3)
detects "Bottom Roll Deck
open" when "H".
Cut Sheet Size Sensor 0
(PH31, 33, 35 & 37) detects
the media when "L".
Developer Unit Position
Sensor (PH25) detects the
Developer Unit is pressed to
the Drum when "L".
Internal Transportation Unit
Set Sensor (PH24) detects
the Internal Transportation
Unit is set when "H".
Cut Sheet Size Sensor 0
(PH32, 34 & 36) detects the
media when "L".
Separation Sensor (PH18)
detects the media when "L".
Exit Sensor (LS2) detects the
media when "L".
K115sm8e1.doc
I / O F.C.
I NO
I NO
I NO
I NO
I NO
I NO
I NO
I NO
I NO
I NO
I NO
I NO
I NO
I NO
I NO
I NO
I NO
I NO
I NO
I NO
I NO