KIP 9000 Service Manual page 539

Code Signal name IC Port
34 DEV_ST U015 P54
35 ------- U015 P55
36 WEB_END U015 P56
37 ------- U015 P57
38 SW_R U017 P40
39 PF_SPH U017 P41
3A T_SL1 U017 P42
3b T_SL2 U017 P43
3C T_MTR U017 P44
3d POW_24V U017 P45
3E SEPBLW4 U017 P46
3F SEPBLW3 U017 P47
40 INT1 U015 P60
41 INT2 U015 P61
42 WCMTR_OC U015 P62
43 CUTHP_O U015 P63
44 BIAS_ST U015 P64
45 PWR_ST U015 P65
46 DRMTR_LD U015 P66
47 LEDMTR_OC U015 P67
48 DISP_DT24 U016 P50
49 DISP_DT25 U016 P51
4A DISP_DT26 U016 P52
4B DISP_DT27 U016 P53
4C DISP_DT28 U016 P54
4D DISP_DT29 U016 P55
4E DISP_DT30 U016 P56
4F DISP_DT31 U016 P57
50 DISP_DT8 U016 P60
51 DISP_DT9 U016 P61
NOTES
1. I / O means input signal or output signal.
2. F.C. means Function Checking (Mode).
If the signal is provided with "OK", concerning target (motors, blowers and so on) is operatable
in the Function Checking Mode. (Refer to [8.1.4 Function Checking Mode] on and after the
page 8-32.) If the signal is provided with "NO", it is not operatable.
Connector Signal
J205-9 Developer Setting Status
Signal
J205-10
J205-11 Web Sensor Signal
J205-12
J208-A35 Power Switch OFF Control
Signal
J208-B35 Paper Feed Motor Speed
Change Signal
J208-A36 Bypass Feeding Roller Down
Solenoid Control Signal
J208-B36 Bypass Reversal Roller
Down Solenoid Control
Signal
J208-A37 Bypass Feeding Motor
Control Signal
J208-B37 24V Relay
J208-A38 Separation Assist Blower 4
Control Signal
J208-B38 Separation Assist Blower 3
Control Signal
J204-1 Interlock Signal 1
(Thermostat)
J204-2 Interlock Signal 2
(Door / Thermostat)
J204-3 Wire Cleaning Motor Over
Current Detection Signal
J204-4 Cutter Home Position Signal
J204-5 Developer Bias Output 2
Detection Signal
J204-6 Power Switch Detection
Signal
J204-7 Drum Motor Synchronous
Signal
J204-8 LED Head Cleaning Motor
Over Current Detection
Signal
J214-1 Indication Data Signal 24
J214-2 Indication Data Signal 25
J214-3 Indication Data Signal 26
J214-4 Indication Data Signal 27
J214-5 Indication Data Signal 28
J214-6 Indication Data Signal 29
J214-7 Indication Data Signal 30
J214-8 Indication Data Signal 31
J214-9 Indication Data Signal 8
J214-10 Indication Data Signal 9
8-14
Condition
Connector of Developer is
disconnected.
Web Sensor detects "Web
End" when "L".
Power Switch (S1) is turned
OFF when "H" is outputted.
Paper Feed Motor (M2)
rotates fast when "H".
It rotates slowly when "L".
Bypass Feeding Roller Down
Solenoid (SL3) operates
when "H".
Bypass Reversal Roller Down
Solenoid (SL4) operates
when "H".
Bypass Feeding Motor (M10)
rotates when "H".
Separation Assist Blower 4
(BL12 & 16) rotate when "H".
Separation Assist Blower 3
(BL13 & 15) rotate when "H".
Thermostat (TS1) is open
when "H".
Thermostat (TS1) or some
door is open when "H".
Over current flows when "L".
Cutter Home Position Sensor
(PH22) detects the Cutter is
at the Home Position when
"L".
Bias is normally supplied
when "H".
Power Switch (S1) is ON
when "L".
Drum Motor (M1) rotates
when "L".
Over current flows when "L".
K115sm8e1.doc
I / O F.C.
I NO
O OK
O OK
O OK
O OK
O OK
I NO
O OK
O OK
I NO
I NO
I NO
I NO
I NO
I NO
I NO
I NO
O NO
O NO
O NO
O NO
O NO
O NO
O NO
O NO
O NO
O NO