Signal Code List - KIP 9000 Service Manual

8. 1. 2. 4

Signal code list

Code Signal name IC Port
00 UPPER_SW U015 P30
01 RIGHT_SW1 U015 P31
02 RIGHT_SW2 U015 P32
03 MP_SRT U015 P33
04 RP_SET1 U015 P34
05 RP_SET2 U015 P35
06 RP_SET3 U015 P36
07 RP_SET4 U015 P37
08 RF_CLK1 U015 P20
09 RF_CLK2 U015 P21
0A RF_CLK3 U015 P22
0b RF_CLK4 U015 P23
0C PSEL_DT0 U015 P24
0d PSEL_DT1 U015 P25
0E PSEL_DT2 U015 P26
0F PSEL_DT3 U015 P27
10 SZDATA0 U015 P17
11 SZDATA1 U015 P18
12 SZDATA2 U015 P19
13 SZDATA3 U015 P20
14 SZDATA4 U015 P21
15 SZDATA5 U015 P22
16 SZDATA6 U015 P23
17 SZDATA7 U015 P24
NOTES
1. I / O means input signal or output signal.
2. F.C. means Function Checking (Mode).
If the signal is provided with "OK", concerning target (motors, blowers and so on) is operatable
in the Function Checking Mode. (Refer to [8.1.4 Function Checking Mode] on and after the
page 8-32.) If the signal is provided with "NO", it is not operatable.
Connector Signal
J202-1 Top Rear Cover Signal
J202-2 Right Side Door Signal
J202-3 Toner Cover Signal
J202-4 Bypass Start Sensor Signal
J202-5 Roll Set Sensor 1 Signal
J202-6 Roll Set Sensor 2 Signal
J202-7 Roll Set Sensor 3 Signal
J202-8 Roll Set Sensor 4 Signal
J202-9 Paper Feed Clock Sensor 1
Signal
J202-10 Paper Feed Clock Sensor 2
Signal
J202-11 Paper Feed Clock Sensor 3
Signal
J202-12 Paper Feed Clock Sensor 4
Signal
J202-13 Media Selection Signal 0
(Plain paper)
J202-14 Media Selection Signal 1
(Tracing paper)
J202-15 Media Selection Signal 2
(Film)
J202-16 Inch Media Switch Signal
(ENG. / ARCH.)
J202-17 Paper Size Sensor Signal 0
J202-18 Paper Size Sensor Signal 1
J202-19 Paper Size Sensor Signal 2
J202-20 Paper Size Sensor Signal 3
J202-21 Paper Size Sensor Signal 4
J202-22 Paper Size Sensor Signal 5
J202-23 Paper Size Sensor Signal 6
J202-24 15" Size Sensor Signal
8-12
Condition
Top Rear Cover Switch (DS6)
detects door open when "H".
Right Side Door Switch (DS7)
detects door open when "H".
Toner Cover Switch (DS8)
detects door open when "H".
Bypass Start Sensor (PH20)
detects the media when "L".
Roll Set Sensor 1 (PH1)
detects the media when "L".
Roll Set Sensor 2 (PH2)
detects the media when "L".
Roll Set Sensor 3 (PH3)
detects the media when "L".
Roll Set Sensor 4 (PH4)
detects the media when "L".
Paper Feed Clock Sensor 1
(PH13) generates the clock
pulse when the media is fed.
Paper Feed Clock Sensor 2
(PH14) generates the clock
pulse when the media is fed.
Paper Feed Clock Sensor 3
(PH15) generates the clock
pulse when the media is fed.
Paper Feed Clock Sensor 4
(PH16) generates the clock
pulse when the media is fed.
"Plain Paper" of Media
Selector is pressed down
when "H".
"Tracing Paper" of Media
Selector is pressed down
when "H".
"Film" of Media Selector is
pressed down when "H".
"Engineering" when "L".
"Architecture" when "H".
Paper Size Sensor 0 (PH5A,
5B, 5C & 5D) detects the
media when "L".
Paper Size Sensor 1 (PH6A,
6B, 6C & 6D) detects the
media when "L".
Paper Size Sensor 2 (PH7A,
7B, 7C & 7D) detects the
media when "L".
Paper Size Sensor 3 (PH8A,
8B, 8C & 8D) detects the
media when "L".
Paper Size Sensor 4 (PH9A,
9B, 9C & 9D) detects the
media when "L".
Paper Size Sensor 5 (PH10A,
10B, 10C & 10D) detects the
media when "L".
Paper Size Sensor 6 (PH11A,
11B, 11C & 11D) detects the
media when "L".
Paper Size Sensor (PH41)
on Roll 1detects the media
when "L".
K115sm8e1.doc
I / O F.C.
I NO
I NO
I NO
I NO
I NO
I NO
I NO
I NO
I NO
I NO
I NO
I NO
I NO
I NO
I NO
I NO
I NO
I NO
I NO
I NO
I NO
I NO
I NO
I NO