KIP 9000 Service Manual page 540

Code Signal name IC Port
52 DISP_DT10 U016 P62
53 DISP_DT11 U016 P63
54 DISP_DT12 U016 P64
55 DISP_DT13 U016 P65
56 DISP_DT14 U016 P66
57 DISP_DT15 U016 P67
58 DISP_DT16 U016 P70
59 DISP_DT17 U016 P71
5A DISP_DT18 U016 P72
5B DISP_DT19 U016 P73
5C DISP_DT20 U016 P74
5D DISP_DT21 U016 P75
5E DISP_DT22 U016 P76
5F DISP_DT23 U016 P77
60 RY6 U017 P50
61 U005 CLK U017 P51
62 U005 DI U017 P52
63 U005 BS U017 P53
64 U002 A U017 P54
65 U002 B U017 P55
66 U002 C U017 P56
67 ------- U017 P57
68 DPMTR U017 P20
69 CUTMTR U017 P21
6A DP_CHG U017 P22
6B CMTR_RST U017 P23
6C WCMTR U017 P24
6D PRESBLW_H U017 P25
6E WCMTR_DIR U017 P26
6F PRESBLW_L U017 P27
70 PFMTR_DIR U017 P30
71 ------- U017 P31
NOTES
1. I / O means input signal or output signal.
2. F.C. means Function Checking (Mode).
If the signal is provided with "OK", concerning target (motors, blowers and so on) is operatable
in the Function Checking Mode. (Refer to [8.1.4 Function Checking Mode] on and after the
page 8-32.) If the signal is provided with "NO", it is not operatable.
Connector Signal
J214-11 Indication Data Signal 10
J214-12 Indication Data Signal 11
J214-13 Indication Data Signal 12
J214-14 Indication Data Signal 13
J214-15 Indication Data Signal 14
J214-16 Indication Data Signal 15
J214-17 Indication Data Signal 16
J214-18 Indication Data Signal 17
J214-19 Indication Data Signal 18
J214-20 Indication Data Signal 19
J214-21 Indication Data Signal 20
J214-22 Indication Data Signal 21
J214-23 Indication Data Signal 22
J214-24 Indication Data Signal 23
J208-B28 Rylay6 (RY6) Control Signal
Shift Lock of M62362P CLK
Serial Data of M62362P DI
BS of M62362P
Selector A of 74HC4051
Selector B of 74HC4051
Selector C of 74HC4051
J208-A29 Developer Positioning Motor
Control Signal
J208-B29 Cutter Motor Control Signal
J208-A30 Developer Release Power
Charge Control Signal
J208-B30 Cutter Motor Reset Signal
J208-A31 Wire Cleaning Motor Control
Signal
J208-B31 Paper Pressure Blower
(High Speed)
J208-A32 Wire Cleaning Motor
Reverse Signal
J208-B32 Paper Pressure Blower
(Low Speed)
J208-A33 Paper Feed Motor Reverse
Control Signal
J208-B33
8-15
Condition
36V is controlled when "H".
Developer Positioning Motor
(M4) rotates when "H".
Cutter Motor (M3) rotates
when "H".
Power for releasing the
Developer Unit is charged
when "H".
Cutter is reset when "H".
Wire Cleaning Motor (M9)
rotates when "H".
Pressure Blowers (BL4, 5, 6
&7) rotate in a high speed
when "H".
Wire Cleaning Motor (M9)
rotates oppositely when "H".
Pressure Blowers (BL4, 5, 6
&7) rotate in a low speed
when "H".
Paper Feed Motor (M2)
rotates oppositely when "H".
K115sm8e1.doc
I / O F.C.
O NO
O NO
O NO
O NO
O NO
O NO
O NO
O NO
O NO
O NO
O NO
O NO
O NO
O NO
O NO
- NO
- NO
- NO
- NO
- NO
- NO
-
O OK
O OK
O OK
O OK
O OK
O OK
O OK
O OK
O OK