Motorola CMOS Logic Manual page 494

Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î
ELECTRICAL CHARACTERISTICS
Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î
Characteristic
Output Voltage "0" Level
V in = V DD or 0
"1" Level
V in = 0 or V DD
Input Voltage "0" Level
(V O = 4.5 or 0.5 Vdc)
(V O = 9.0 or 1.0 Vdc)
(V O = 13.5 or 1.5 Vdc)
"1" Level
(V O = 0.5 or 4.5 Vdc)
(V O = 1.0 or 9.0 Vdc)
(V O = 1.5 or 13.5 Vdc)
Output Drive Current
(V OH = 2.5 Vdc)
(V OH = 4.6 Vdc)
(V OH = 9.5 Vdc)
(V OH = 13.5 Vdc)
(V OL = 0.4 Vdc)
(V OL = 0.5 Vdc)
(V OL = 1.5 Vdc)
Input Current
Input Capacitance
(V in = 0)
Quiescent Current
(Per Package)
Total Supply Current**†
(Dynamic plus Quiescent,
Per Package)
(C L = 50 pF on all outputs, all
buffers switching)
#Data labelled "Typ" is not to be used for design purposes but is intended as an indication of the IC's potential performance.
** The formulas given are for the typical characteristics only at 25 _ C.
†To calculate total supply current at loads other than 50 pF:
I T (C L ) = I T (50 pF) + (C L – 50) Vfk
where: I T is in µA (per package), C L in pF, V = (V DD – V SS ) in volts, f in kHz is input frequency, and k = 0.001.
This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However,
precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance
circuit. For proper operation, V in and V out should be constrained to the range V SS
Unused inputs must always be tied to an appropriate logic voltage level (e.g., either V SS or V DD ). Unused outputs must
be left open.
MC14566B
6–456
(Voltages Referenced to V SS )
V DD V DD
Vdc
Symbol Min
V OL 5.0
10
15
V OH 5.0 4.95
10 9.95
15 14.95
V IL
5.0
10
15
V IH
5.0
10
15
I OH
Source 5.0 – 3.0
5.0 – 0.64
10 – 1.6
15 – 4.2
Sink I OL 5.0 0.64
10
15
I in 15
C in —
I DD 5.0
10
15
I T 5.0
10
15
– 55 _ C 25 _ C
Max Min Typ #
— 0.05 — 0
— 0.05 — 0
— 0.05 — 0
— 4.95 5.0
— 9.95 10
— 14.95 15
— 1.5 — 2.25
— 3.0 — 4.50
— 4.0 — 6.75
3.5 — 3.5 2.75
7.0 — 7.0 5.50
11 — 11 8.25
— – 2.4 – 4.2
— – 0.51 – 0.88
— – 1.3 – 2.25
— – 3.4 – 8.8
— 0.51 0.88
1.6 — 1.3 2.25
4.2 — 3.4 8.8
— 0.1 — 0.00001
— — — 5.0
— 5.0 — 0.005
— 10 — 0.010
— 20 — 0.015
I T = (1.0 µA/kHz) f + I DD
I T = (2.0 µA/kHz) f + I DD
I T = (3.0 µA/kHz) f + I DD
125 _ C
Max Min Max
0.05 — 0.05
0.05 — 0.05
0.05 — 0.05
— 4.95 —
— 9.95 —
— 14.95 —
1.5 — 1.5
3.0 — 3.0
4.0 — 4.0
— 3.5 —
— 7.0 —
— 11 —
— – 1.7 —
— – 0.36 —
— – 0.9 —
— – 2.4 —
— 0.36 —
— 0.9 —
— 2.4 —
0.1 — 1.0
7.5 — —
5.0 — 150
10 — 300
20 — 600
(V in or V out ) V DD .
MOTOROLA CMOS LOGIC DATA
Unit
Vdc
Vdc
Vdc
Vdc
mAdc
mAdc
µAdc
pF
µAdc
µAdc