Ezgo 1600xd Repair Manual page 412

Piston ring end gap.......................................... 3-43
Piston rings ......................................................... 3-7
Piston, fl ywheel and crankshaft ........................ 3-66
Pistons ................................................................ 3-8
Power outlet.................................................... 12-46
Preheat relay (4P) .......................................... 12-36
Preheating and post heating........................... 12-11
Principle of cooling system for CVT .................... 4-7
Propeller shaft (front universal joint) replacement ....9-26
R
Radiator cap ..................................................... 3-21
Radiator ............................................................ 3-21
Radiator .............................................................. 3-9
Rear axle case disassembly and assembly...... 7-17
Rear axle case oil ............................................... 7-2
Rear axle case removal(rear axle disassembly) .... 7-14
Rear axle power transfer diagram ...................... 7-4
Rear axle replacement ..................................... 7-22
Rear carrier replacement .................................. 7-27
Rear differential system disassembly and
assembly .......................................................... 7-20
Rear propeller shaft replacement ..................... 7-28
Rear wheel brake removal (brake pad and disc
replacement) ...................................................... 8-9
Relief valve ...................................................... 3-18
Right after the engine starts .......................... 12-14
Rocker arm assembly ...................................... 3-13
Rocker arm assembly check ............................ 3-40
Rocker arm ....................................................... 3-70
Routes for various cables ................................... 6-4
S
Safe workplace ................................................... 1-3
Safety decals ...................................................... 1-2
Safety decals ...................................................... 1-9
Safety equipment................................................ 1-3
Safety gear ......................................................... 1-3
Safety instructions when preparing tractor ......... 1-4
Safety start switch .......................................... 12-24
Safety tips ........................................................... 1-3
Scald prevention ................................................. 1-7
Sealant and adhesive(CVT) ............................... 4-2
Sealant and adhesive(Transmission) ................. 5-3
13
-6
INDEX
Sealant and adhesive(Front axle)....................... 9-3
Seat and fender removal .................................... 6-7
Serial number ..................................................... 2-3
Service specifi cations ......................................... 3-6
Shift cable length .............................................. 5-12
Shift selector cable ............................................. 6-4
Shift system ........................................................ 5-6
Slow-blow fuse ............................................... 12-21
Snap ring assembly .......................................... 2-18
Specifi cation(Electric system)........................... 12-3
Specifi cations(Steering).................................... 10-2
Specifi cations(Hydraulic system)...................... 11-2
Specifi cations(General) ...................................... 2-6
Specifi cations(Engine) ........................................ 3-4
Specifi cations(CVT) ............................................ 4-2
Specifi cations(Transmission) .............................. 5-2
Specifi cations(Chassis) ...................................... 6-2
Specifi cations(Rear axle).................................... 7-2
Specifi cations(Brake).......................................... 8-2
Specifi cations(Front axle) ................................... 9-2
Specifi ed infl ation pressure .............................. 2-13
Speed control lever plate and governor spring .... 3-61
Speed control system ......................................... 5-5
Speed sensor ................................................. 12-30
Speedometer operation with the engine running... 12-63
Spring pin installation ....................................... 2-18
Start relay (5P) ............................................... 12-44
Steering column removal and installation ......... 10-9
Steering gearbox components.......................... 10-5
Steering gearbox removal ................................ 10-8
Steering gearbox .............................................. 10-2
Structure and function(Steering)....................... 10-3
Structure and function(Engine) ......................... 3-11
Structure and function(Rear axle)....................... 7-3
Structure and function(Brake)............................. 8-3
Structure and function(Front axle) ...................... 9-4
Structure and operating principle(CVT) .............. 4-3
Structure and operating principle(Transmission) ... 5-4
Structure in steering gearbox ........................... 10-4
Structure of CVT(continuously variable
transmission) ...................................................... 4-3
Structure of rear axle section.............................. 7-3
SUUV-W00 Apr. 2011