Ezgo 1600xd Repair Manual page 411

Headlamp ....................................................... 12-20
Hood, panel, fl oor and radiator removal ............. 6-9
Hour meter operation...................................... 12-65
How to install spring pin and snap ring ............. 2-18
Hydraulic circuit ................................................ 11-5
Hydraulic component layout ............................. 11-3
Hydraulic line .................................................... 11-6
I
Idle gear oil clearance measurement ............... 3-48
Idle gear shaft, oil pump and oil pan................. 3-65
Idle gear side clearance ................................... 3-47
Illumination ......................................................... 1-3
Injection nozzle inspection................................ 3-37
Injection nozzle ................................................. 3-71
Injection pump .................................................... 3-9
Inlet and exhaust valves .................................. 3-13
Inspection and adjustment(Steering) ................ 10-7
Inspection and adjustment(Front axle) ............... 9-8
Inspection and adjustment(Hydraulic system) ... 11-19
Inspection and adjustment(Engine) .................. 3-34
Inspection and adjustment(CVT) ........................ 4-9
Inspection and adjustment(Transmission) .......... 5-9
Inspection and adjustment(Chassis) .................. 6-3
Inspection and adjustment(Rear axle) ................ 7-9
Inspection and adjustment(Brake) ...................... 8-6
Installation direction of front/rear tires ................ 6-3
Instrument panel ............................................. 12-38
Intake and exhaust system ............................... 3-30
Intake and exhaust valves ................................ 3-38
Intake and exhaust valves ................................ 3-70
K
Keeping your work area clean ............................ 1-3
Key switch ...................................................... 12-32
L
Location of electrical devices............................ 12-7
Lsd (limited slip device) ...................................... 9-6
Lsd disassembly and assembly ........................ 9-22
Lubrication and replenishment ......................... 2-12
Lubrication system............................................ 3-16
M
Main bearing case assembly ............................ 3-75
SUUV-W00 Apr. 2011
INDEX
Main relief valve pressure............................... 11-19
Maintenance schedule chart............................. 2-10
Maintenance ..................................................... 2-10
Measuring the piston compression pressure .... 3-34
Mls cylinder head gasket .................................. 3-15
Muffl er............................................................... 3-30
Njection pump gear assembly
(fuel camshaft gear) ......................................... 3-76
Nuts .................................................................. 2-17
Oil clearance between crank pin and connecting
rod big end bearing ........................................... 3-45
Oil clearance between crankshaft journal and
bearing 1 .......................................................... 3-44
Oil clearance between crankshaft journal and
bearing 2 .......................................................... 3-45
Oil pressure switch .......................................... 3-18
Oil pump .......................................................... 3-19
Oil pump check ................................................. 3-50
Oil pump ............................................................. 3-9
Operating principle of differential lock system .... 7-7
Operating principle of differential system ........... 7-6
Operating principle(Hydraulic system).............. 11-3
Operating principle(Electric system) ................. 12-9
Operating principle(CVT) .................................... 4-4
Operating system diagram ............................... 10-3
Operation of governor....................................... 3-29
Others location ................................................... 2-4
Parking brake cable ............................................ 6-5
Parking brake disassembly and assembly
(parking brake pad replacement) ..................... 8-15
Parking brake switch ...................................... 12-23
Parking brake wire installation (length adjustment) ....8-8
Parking brake ..................................................... 8-4
Part number assignment standard for daedong
bolts and nuts ................................................... 2-16
Pcv valve .......................................................... 3-31
Piston assembly ............................................... 3-72
Piston check ..................................................... 3-42
Piston pin bore.................................................. 3-42
Piston ring clearance ........................................ 3-43
N
O
P
13
-5