Huawei NetEngine80E Configuration Manual - Reliability page 1090

HUAWEI NetEngine80E/40E Router
Configuration Guide - Reliability
5.
Issue 02 (2014-09-30)
[RSG2-Eth-Trunk10.1] quit
Configure primary/secondary status negotiation for PWs.
a. Configure Eth-Trunk interfaces.
# Configure RSG1.
[RSG1] interface gigabitethernet 1/0/2
[RSG1-GigabitEthernet1/0/2] undo shutdown
[RSG1-GigabitEthernet1/0/2] quit
[RSG1] interface eth-trunk 10
[RSG1-Eth-Trunk10] mode lacp-static
[RSG1-Eth-Trunk10] trunkport gigabitethernet 1/0/2
[RSG1-Eth-Trunk10] quit
# Configure RSG2.
[RSG2] interface gigabitethernet 1/0/1
[RSG2-GigabitEthernet1/0/1] undo shutdown
[RSG2-GigabitEthernet1/0/1] quit
[RSG2] interface eth-trunk 10
[RSG2-Eth-Trunk10] mode lacp-static
[RSG2-Eth-Trunk10] trunkport gigabitethernet 1/0/1
[RSG2-Eth-Trunk10] quit
# Configure the RNC.
[RNC] interface gigabitethernet 1/0/1
[RNC-GigabitEthernet1/0/1] undo shutdown
[RNC-GigabitEthernet1/0/1] quit
[RNC] interface gigabitethernet 1/0/2
[RNC-GigabitEthernet1/0/2] undo shutdown
[RNC-GigabitEthernet1/0/2] quit
[RNC] interface eth-trunk 10
[RNC-Eth-Trunk10] portswitch
[RNC-Eth-Trunk10] mode lacp-static
[RNC-Eth-Trunk10] port trunk allow-pass vlan 10
[RNC-Eth-Trunk10] trunkport gigabitethernet 1/0/1 to 1/0/2
[RNC-Eth-Trunk10] quit
[RNC] vlan 10
[RNC-vlan10] quit
b. Configure an E-Trunk and add the preceding Eth-Trunks to the E-Trunk.
# Configure RSG1.
[RSG1] lacp e-trunk system-id 00e0-fc00-0000
[RSG1] lacp e-trunk priority 100
[RSG1] e-trunk 10
[RSG1-e-trunk-10] priority 10
[RSG1-e-trunk-10] peer-address 3.3.3.3 source-address 2.2.2.2
[RSG1-e-trunk-10] quit
[RSG1] interface eth-trunk 10
[RSG1-Eth-Trunk10] e-trunk 10
[RSG1-Eth-Trunk10] quit
# Configure RSG2.
[RSG2] lacp e-trunk system-id 00e0-fc00-0000
[RSG2] lacp e-trunk priority 100
[RSG2] e-trunk 10
[RSG2-e-trunk-10] priority 20
[RSG2-e-trunk-10] peer-address 2.2.2.2 source-address 3.3.3.3
[RSG2-e-trunk-10] quit
[RSG2] interface eth-trunk 10
[RSG2-Eth-Trunk10] e-trunk 10
[RSG2-Eth-Trunk10] quit
# Verify the configuration. Run the display mpls l2vc command to check the status
of the primary and secondary PWs. The following example uses the command output
on the CSG.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
10 Bit-Error-Triggered Protection Switching Configuration
1073