Page 1 Avaya Reference Guide P330 VAYA TACKABLE WITCH OFTWARE ERSION April 2003...
Page 3: Table Of Contents
Entering the Supervisor Level .............. 6 Entering the CLI ..................7 Entering the Technician Level .............. 7 Chapter 2 Avaya P330 Layer 2 CLI Commands .............. 9 clear cam ....................9 clear dot1x config ..................9 clear dynamic vlans ................10 clear log ....................
Page 18 Table of Contents Avaya P330 Reference Guide...
Page 19: Chapter 1 Using The Cli
The Switch CLI entity is used to manage Layer 2 switching of the entire stack. The Switch CLI entity is identical to the CLI of a P330 Layer 2 modules. CLI commands for managing Layer 2 switching are described in Chapter 2.
Page 20: Conventions Used
Module number in the prompt is generic and is represented by “N”. • Security level - used as the suffix of the prompt (Refer to Security Level on page 6.) • Application context - used as body of the prompt, this part is not mandatory. Avaya P330 Reference Guide...
Page 21: Navigation, Cursor Movement And Shortcuts
For example, version can be abbreviated ver. For ambiguous commands, type the beginning letters on the command line and then use the Tab key to toggle through all the possible commands beginning with these letters. Avaya P330 Reference Guide...
Page 22: Universal Commands
The syntax for this command is: tree P330 Sessions You can use sessions to switch between the CLI of P330 modules / other stack entities (for example, an X330 ATM or WAN entity plugged into a specific P330 switch or with the G700 Media Gateway Precessor) or to switch between Layer 2 and Layer 3 commands in the router module.
Page 23 Note: Use the session command without any parameters to identify the stack master and its slot number. It will list all the modules in the stack and their slot number with the master module marked with an asterisk. Avaya P330 Reference Guide...
Page 24: Security Levels
Welcome to P330 Login: root Password:**** Password accepted. P330-N(super)# Defining new users Define new users and access levels using the username command in Supervisor Level. Exiting the Supervisor Level To exit the Supervisor level, type the command exit. Avaya P330 Reference Guide...
Page 25: Entering The Cli
Entering the Technician Level This level is can only be accessed from the Privileged and Supervisor levels not from the User level. This feature is not documented and is for use by Avaya Technical Support only. Avaya P330 Reference Guide...
Page 26 Chapter 1 Using the CLI Avaya P330 Reference Guide...
Page 27: Chapter 2 Avaya P330 Layer 2 Cli Commands
Chapter 2 Avaya P330 Layer 2 CLI Commands This chapter describes all the P330 Layer 2 CLI commands and parameters in alphabetical order. clear cam User level: privileged, supervisor. Use the clear cam command to delete all entries from the CAM table.
Page 28: Clear Dynamic Vlans
User level: privileged, supervisor. This command is available on the P330-ML only. Use the clear dynamic vlans command to clear dynamically learned VLANs. Only the VLANs learned by the switch from incoming traffic are cleared using this command.
Page 29: Clear Port Mirror
Chapter 2 Avaya P330 Layer 2 CLI Commands clear port mirror User level: privileged, supervisor. Use the clear port mirror command to cancel port mirroring. The syntax for this command is: clear port mirror [<source module>/<source port>/<dest module>/<dest port>] source module...
Page 30: Clear Radius Authentication Server
User level: privileged, supervisor. This command is is not available on P330-ML switches. If this command is to be implemented on a switch other than the stack master, a session should be opened to the relevant switch.
Page 31: Clear Snmp Trap
Chapter 2 Avaya P330 Layer 2 CLI Commands Example: P330-N# clear secure mac 1-2-3-4-5 port 1/17 01-02-03-04-05 cleared from secure address list for port 1/ clear snmp trap User level: privileged, supervisor. Use the clear snmp trap command to clear an entry from the SNMP trap receiver table.
Page 32: Clear Vlan 100
Chapter 2 Avaya P330 Layer 2 CLI Commands clear vlan User level: privileged, supervisor. Use the clear vlan command to delete an existing VLAN and return ports from this VLAN to the default VLAN #1. When you clear a VLAN, all ports assigned to that VLAN are assigned to the default VLAN #1.
Page 33: Copy Running-Config Startup-Config
Please refrain from any other operation during this time. For more information , use 'show tftp upload status' command ******************************************************************** * If you are currently running the P330 Device Manager application,* * it is recommended to exit from it before performing configuration* * download operations.
Page 34: Copy Running-Config Tftp
Chapter 2 Avaya P330 Layer 2 CLI Commands copy running-config tftp User level: privileged, supervisor. This command applies to the P334T-ML only when it is in “Layer2” device mode. Use the copy running-config tftp command to upload the policy configuration to a TFTP server.
Page 35: Copy Startup-Config Tftp
Please refrain from any other operation during this time. For more information , use 'upload status' command ******************************************************************** * If you are currently running the P330 Device Manager application,* * it is recommended to exit from it before performing configuration* * download operations.
Page 36: Copy Tftp Ew_Archive
Avaya P330 Layer 2 CLI Commands copy tftp EW_archive User level: privileged, supervisor. Use the copy tftp EW-archive command to download the P330 Manager application into the switch from a TFTP server. The syntax for this command is: copy tftp EW_archive <filename> <ip> <module number>...
Page 37: Copy Tftp Stack-Config
Chapter 2 Avaya P330 Layer 2 CLI Commands Example (for Windows): Router-N# copy tftp module-config c:\config\switch1.cfg 192.168.49.10 Example: (for Unix): Router-N# copy tftp module-config /folder/startup.cfg 192.168.49.10 copy tftp stack-config Use the copy tftp stack-config command to download the stack-level configuration from a saved file into the current NVRAM running configuration from a TFTP server.
Page 38: Copy Tftp Startup-Config
Chapter 2 Avaya P330 Layer 2 CLI Commands copy tftp startup-config User level: privileged, supervisor. This command applies to the P334T-ML only when it is in “Layer2” device mode. Use the copy tftp startup-config command to download a policy configuration from the saved TFTP file to the Startup Configuration file in the NVRAM.
Page 39 EW_image x 149.49.138.170 1 If file "x" does not exist, the Embedded web image will not be downloaded and bank A will retain the previous SW version image. Example: P330-N# copy tftp SW_image /home/P330/viisa EW_archive 1 135.64.103.104 1 Module Source file...
Page 40: Copy Tftp Sw_Powerinline_Image
Chapter 2 Avaya P330 Layer 2 CLI Commands Module Source file : /home/P330/viisa Destination file : P330 Host : 135.64.103.104 Running state : Downloading ... Failure display : no-error Last warning Module Source file : /home/P330/viisa Destination file : P330 Host : 135.64.103.104...
Page 41: Dir
Chapter 2 Avaya P330 Layer 2 CLI Commands Example: P330-2# copy tftp SW_powerinline_image c:\p333t\p333T_203 192.168.49.10 Module: Source file: c:\p333t\p333t_203 Destination file: Powerinline Host: 192.168.49.10 Running state: Downloading Failure Display: Access Violation Last warning: Download completed Before executing the download, the following checks will be performed by embedded SW, on the TFTP server file: —...
Page 42 This file Can’t be replaced by the user. • startup-config - file which contains the startup (saved in NVRAM) configuration for policy and routing in the P330- ML, P333R and P333R-LB • running-config - file which contains the running (currently...
Page 43: Get Time
Chapter 2 Avaya P330 Layer 2 CLI Commands get time Use the get time command to retrieve the time from the network. The syntax for this command is: get time Example: P330-N>get time Time is being acquired from server 0.0.0.0 Time has been acquired from the network.
Page 44: Ip Access-List
Chapter 2 Avaya P330 Layer 2 CLI Commands Examples: P330-N# hostname Session hostname is ‘P330’ P330-N# hostname “gregory” gregory-N# gregory-N# no hostname P330-N# If you wish to enter a name which includes spaces, you must enclose the entire name in quotation marks, for example “new york”.
Page 45: Ip Access-List-Cookie
Chapter 2 Avaya P330 Layer 2 CLI Commands <source-ip> ip address of the source network <source-wildcard> ip address wildcard of the source network <operator> eq | lt | gt | range <port> integer (1...65535) <destination-ip> ip address of the destination network <destination-wildcard>...
Page 46: Ip Access-List-Copy
Chapter 2 Avaya P330 Layer 2 CLI Commands ip access-list-copy User level: privileged, supervisor. This command applies to the P334T-ML only when it is in device mode "Layer2". Use the ip access-list-copy command to copy a configured source policy list to a destination policy list.
Page 47: Ip Access-List-Dscp Operation
Chapter 2 Avaya P330 Layer 2 CLI Commands ip access-list-dscp operation User level: privileged, supervisor. This command applies to the P334T-ML only when it is in device mode "Layer2". Use the ip access-list-dscp operation command to set a DSCP to CoS mapping.
Page 48: Ip Access-List-Name
Chapter 2 Avaya P330 Layer 2 CLI Commands untrusted Forward the packet with priority 0 trust-cos Forward the packet with its original 802.1p priority (default) trust-dscp Forward the packet with the maximum priority between 802.1p and the priority obtained from the DSCP-CoS mapping table...
Page 49: Ip Simulate
Chapter 2 Avaya P330 Layer 2 CLI Commands The syntax for this command is: ip access-list-owner <policy-list-number> <owner> <policy-list-number> integer (100...149) <owner> list owner Example: Router-N# ip access-list-owner 101 admin Done! ip simulate User level: privileged, supervisor. This command applies to the P334T-ML only when it is in device mode "Layer2".
Page 50 Chapter 2 Avaya P330 Layer 2 CLI Commands Example: Router-N(configure)# ip simulate 100 192.67.85.12 193.76.54.25 Avaya P330 Reference Guide...
Page 51: No Rmon Alarm
Use the no rmon alarm command to delete an existing RMON alarm entry. The syntax for this command is: no rmon alarm <Alarm Index> Alarm Index Alarm index defined using rmon alarm command or P330 Manager Example: P330-N# no rmon alarm 1026 no rmon event User level: privileged, supervisor.
Page 52: No Username
Chapter 2 Avaya P330 Layer 2 CLI Commands no username User level: supervisor Use the no username command to remove a local user account. The syntax for this command is: no username <name> name User name Example: P330-1(super)# no username john User account removed.
Page 53: Ping
Chapter 2 Avaya P330 Layer 2 CLI Commands ping User level: user, privileged, supervisor Use the ping command to send ICMP echo request packets to another node on the network. You can use this command via the master switch only.
Page 54: Reset
Chapter 2 Avaya P330 Layer 2 CLI Commands Example: P330-1(super)# prompt-length 4 ~r)# reset User level: user, privileged, supervisor Use the reset command to restart the stack or an individual switch. If no switch number is defined or the switch number of the Master is defined, the command resets the entire stack.
Page 55: Reset Stack
Chapter 2 Avaya P330 Layer 2 CLI Commands Example: P330-N# reset mgp 1 reset stack User level: privileged, supervisor. Use the reset stack command to perform a hardware reset of the entire stack. The syntax for this command is: reset stack...
Page 56: Rmon Alarm
Chapter 2 Avaya P330 Layer 2 CLI Commands rmon alarm User level: privileged, supervisor. Use the rmon alarm command to create a new RMON alarm entry. The syntax for this command is: rmon alarm <Alarm Number> <variable> <interval> <sample type>...
Page 57: Rmon Event
Chapter 2 Avaya P330 Layer 2 CLI Commands rmon event User level: privileged, supervisor. Use the rmon event command to create an RMON event entry. The syntax for this command is: rmon event <Event Number> <type> description <description> owner <owner>...
Page 58: Session
Use the session command to open a session with a specific entity within a switch or the stack. For example, you can open a session with the Routing entity of a P330-ML switch in the stack, or with an the X330 ATM (or X330 WAN) sub-module entity plugged into a specific switch.
Page 59: Set Allowed Managers
Chapter 2 Avaya P330 Layer 2 CLI Commands Example: P330-1# session 2 P330-2# session P333T (*) In Slot 1 P334T In Slot 2 P330-2# set allowed managers User level: privileged, supervisor. Use the set allowed managers command to enables or disable the Allowed Managers feature.
Page 60 Chapter 2 Avaya P330 Layer 2 CLI Commands Example: P330-N# set allowed managers ip add 149.49.32.134 Ip was added to the table Avaya P330 Reference Guide...
Page 61: Set Arp-Aging-Interval
Chapter 2 Avaya P330 Layer 2 CLI Commands set arp-aging-interval User level: privileged, supervisor. Use the set arp-aging interval command to set the ARP table aging interval for entries in the agent Layer 2 ARP table. The entry is deleted at the end of every aging interval. The default value is 10 minutes.
Page 62: Set Autopartition
User level: privileged, supervisor. This command is not relevant to P330-ML switches. It appears in the P330-ML CLI for controlling autopartition of other P330 switches in the stack. Use the set autopartition command to enable or disable auto-partitioning on P330 switches in the stack.
Page 63: Set Cascading
Use the set default queuing scheme command to revert to the default queuing scheme (WRR) of the switch. If this command is to be implemented on a P330-ML switch other than the stack master, a session should be opened to the relevant switch.
Page 64: Set Dot1X Max-Req
Chapter 2 Avaya P330 Layer 2 CLI Commands The syntax for this command is: set device-mode <mode> mode • Router – switch operates at Layers 2 and 3. • Layer2 – switch operates at Layer 2. Example: Router-N# set device-mode Router...
Page 65: Set Dot1X Re-Authperiod
Chapter 2 Avaya P330 Layer 2 CLI Commands Example: P330-1(super)# set dot1x quiet-period 90 Done! set dot1x re-authperiod User level: supervisor Use the set dot1x re-authperiod command to set the idle time between re- authentication attempts. The syntax for this command is: set dot1x re-authperiod <Seconds>...
Page 66: Set Dot1X System-Auth-Control Disable
Chapter 2 Avaya P330 Layer 2 CLI Commands The syntax for this command is: set dot1x supp-timeout <Seconds> Seconds Number of seconds – 0 to 65535 Example: P330-1(super)# set dot1x supp-timeout 90 set dot1x system-auth-control disable User level: supervisor Use the set dot1x system-auth-control disable command to globally disable the PBNAC (802.1x) feature.
Page 67: Set Dot1X Tx-Period
Chapter 2 Avaya P330 Layer 2 CLI Commands • When a RADIUS server is not defined: P330-1(super)# set dot1x system-auth-control enable *** Warning : Authentication server ( RADIUS ) is disabled/ not-exist and so, *** no authentication can be made...
Page 68: Set Intelligent-Multicast
User level: privileged, supervisor. Use the set intelligent-multicast client port pruning time command to set the aging time for client ports. This is the time after the P330 switch reset during which the filtering information is learned by the switch but not configured on the ports.
Page 69: Set Intelligent-Multicast Router-Port-Pruning Time
Chapter 2 Avaya P330 Layer 2 CLI Commands The syntax for this command is: set intelligent-multicast group-filtering-delay time <seconds> seconds Group filtering time in seconds. Example: P330-N# set intelligent-multicast group-filtering-delay time Done! set intelligent-multicast router-port-pruning time User level: privileged, supervisor.
Page 70: Set Interface Ppp
IP parameters, exit modem mode, disconnect the PPP session, or reset the connected modem. You must configure an IP address and net-mask for the P330 before you can establish a PPP connection. The IP address is a dummy address that is shared between two peers, and must be taken from a subnet that is different from the agent’s inband IP subnet.
Page 71: Set Intermodule Port Redundancy
Chapter 2 Avaya P330 Layer 2 CLI Commands set interface ppp {enable|enable-always|disable|off|reset} enable Enable PPP and enter modem mode. enable-always Enter modem mode every time that the proprietary modem cable is plugged into the console port. disable Disable PPP and enter terminal mode Disconnect the active PPP session.
Page 72: Set Intermodule Port Redundancy Off
User level: privileged, supervisor. This command is not relevant to P330-ML switches. It appears in the P330-ML CLI for controlling internal buffering of other P330 switches in the stack. The set internal buffering command allows you to set the size (Maximum, Medium, and Minimum) of the Receive (Rx) buffer allocated to each port of the specified switch.
Page 73: Set Ip Route
User level: privileged, supervisor. Use the set ip route command to add a route to the IP routing table. You can configure from 1 to 10 default static gateways for a P330 switch. The syntax for this command is: set ip route <destination> <gateway>...
Page 74: Set Leaky-Vlan
Use the set license command to activate the SMON and Routing capabilities of the Avaya P330 stack. An Avaya P330 stack can include several Avaya P330 switches. One SMON license is required per Avaya P330 stack; a routing license is required for each P330-ML switch in the stack.
Page 75: Set Logout
Sessions will not be automatically logged out. set mac-aging User level: privileged, supervisor. This command is available on the P330-ML switches only. Use the set mac-aging command to enable or disable the MAC aging function. The syntax for this command is: Set mac-aging <status>...
Page 76: Set Mac-Aging-Time
User level: privileged, supervisor. This command is available on the P330-ML switches only. Use the set mac-aging-time command to set the MAC aging time in minutes. This is the time after which unused MAC addresses in the MAC table are erased.
Page 77: Set Port Channel
Chapter 2 Avaya P330 Layer 2 CLI Commands asym-tx-only The port will advertise asymmetric Tx pause capabilities only. sym-only The port will advertise symmetric pause capabilities only. sym-and-asym-rx The port will advertise both symmetric and asymmetric Rx pause capabilities. Example:...
Page 78: Set Port Classification
Chapter 2 Avaya P330 Layer 2 CLI Commands Example: P330-N# set port channel 1/5-6,8 on my-channel Port 1/5 channel mode set to on 1/102 Port 1/6 was added to channel 1/102 Port 1/8 was added to channel 1/102 set port classification User level: privileged, supervisor.
Page 79: Set Port Dot1X Initialize
The syntax for this command is: set port dot1x max-req <module/port> <count> module/ Module and port number (or range of ports) port count Number of attempts — 1-10 Example: P330-1(super)# set port dot1x max-req 1/2 5 Avaya P330 Reference Guide...
Page 80: Set Port Dot1X Port-Control
- the port is always is blocking state auto - forwarding/blocking depends on authorization outcome force-authorize - the port is always in forwarding state Example: P330-1(super)# set port dot1x port-control 2/3 force- authorize port 1/2 control was set to force-authorize set port dot1x quiet-period Use the set port dot1x quiet-period command to set the 802.1x quiet period...
Page 81: Set Port Dot1X Re-Authentication
| disable Example: P330-1(super)# set port dot1x re-authentication 1/2 enable port 1/2 re-authenticate was set to enable set port dot1x re-authperiod User level: supervisor Use the set port dot1x re-authperiod command to set the the idle time between re-authentication attempts before the session is terminated.
Page 82: Set Port Dot1X Server-Timeout
Number of seconds – 0 to 65535 Example: P330-1(super)# set port dot1x server timeout 1/2 400 set port dot1x supp-timeout User level: supervisor Use the set port dot1x supp-timeout command to set the time for the port to wait for a reply from the Authentication Server before the session is terminated.
Page 83: Set Port Dot1X Tx-Period
Number of seconds — 0-65535 Example: P330-1(super)# set port dot1x quiet-period 1/2 5000 set port duplex User level: privileged, supervisor. Use the set port duplex command to configure the duplex type of an Ethernet or Fast Ethernet port or range of ports. You can configure Ethernet and Fast Ethernet interfaces to either full duplex or half duplex.
Page 84: Set Port Edge Admin State
The port’s admin satte can be set to either edge-port or non-edge- state port. Examples: P330-N# set port edge admin state 1/1 edge-port port 1/1 edge admin state is set to edge-port P330-N# set port edge admin state 1/1 non-edge-port port 1/1 edge admin state is set to non-edge-port set port enable User level: privileged, supervisor.
Page 85: Set Port Flowcontrol
Chapter 2 Avaya P330 Layer 2 CLI Commands port Number of the port on the switch. You can also specify a range of ports separated by a dash, for example, 4/5-13 for ports 5 to 13 on switch 4. Example: P330-N# set port enable 4/1 Port 4/1 enabled.
Page 86: Set Port Level
Chapter 2 Avaya P330 Layer 2 CLI Commands Example: P330-N# set port flowcontrol receive 5/1 on Port 5/1 flow control receive administration status set to on set port level User level: privileged, supervisor. Use the set port level command to set the priority level of a port or range of ports on the switching bus.
Page 87: Set Port Name
- keyword to copy only incoming traffic both - keyword to copy both incoming and outgoing traffic Example: P330-N# set port mirror source-port 3/9 mirror-port 4/10 sampling always direction both Mirroring both Rx and Tx packets from port 3/9 to port 4/10...
Page 88: Set Port Point-To-Point Admin Status
Chapter 2 Avaya P330 Layer 2 CLI Commands If negotiation is disabled, the user can set the speed and duplex of the Fast Ethernet ports. For Fiber Gigbit Ethernet ports it can determine the flow control (pause) mode only. Copper ports in the P332GT-ML can work at 1000Mbps (Full Duplex) only if autonegotiation is enabled on both cable ends and you are using a 4 pair (8 wires) Ethernet cable.
Page 89: Set Port Powerline
Chapter 2 Avaya P330 Layer 2 CLI Commands Example: P330-N# set port point-to-point admin status 1/1 force-true port 1/1 point to point admin status is set to force-true set port powerline User level: privileged, supervisor. This command is available on P333T-PWR switches only Use the set port powerinline command to enable or disable the load detection process and power delivery for the port.
Page 90: Set Port Redundancy
Chapter 2 Avaya P330 Layer 2 CLI Commands The syntax for this command is: set port powerinline priority <module_number/port_number> <priority> module_number Number of the module hosting the port for which a powerline priority level is to be set. port_number Number of the port for which a powerline priority level is to be set.
Page 91: Set Port Redundancy-Intervals
Name for the redundancy scheme (Optional) Example: P330-N# set port redundancy 1/7 2/12 on red1 uplink: Port 2/12 is redundant to port 1/7. Port redundancy is active - entry is effective immediately If you wish to define a name which includes spaces, you must enclose the entire name in quotation marks, for example “new york”.
Page 92: Set Port Security
This command is not applicable to ports on P330-ML switches. This command is used to set port security for ports in other P330 switches in the stack. The syntax for this command is: set port security { enable | disable } [<module>[/<port>]]...
Page 93: Set Port Spantree Cost
Chapter 2 Avaya P330 Layer 2 CLI Commands <module/port> Example: P330-N# port self-loop-discovery Admin_Status enable 1/2 Self-Loop-Discovery enabled on port 1/2. set port spantree cost User level: privileged, supervisor. Use the set port spantree cost command to set the cost of a port. This value defines which port will be allowed to forward traffic if two ports with different costs cause a loop.
Page 94: Set Port Spantree Enable
Chapter 2 Avaya P330 Layer 2 CLI Commands Example: P330-N# set port spantree disable 3/1 port 3/1 was disabled on spantree set port spantree enable User level: privileged, supervisor. Use the set port spantree enable command to enable the spanning tree mode for specific switch ports.
Page 95: Set Port Spantree Priority
240 indicating low priority. Value should be in steps of 16; default value is 128. Example: P330-N# set port spantree priority 3/4 128 port 3/4 spantree priority is 128 Priority value 0 will set the port to Root port.
Page 96: Set Port Static-Vlan
Chapter 2 Avaya P330 Layer 2 CLI Commands The syntax for this command is: set port speed <mod_num>/<port_num> <10MB|100MB|1GB> mod_num Number of the switch. port_num Number of the port on the switch. You can also specify a range of ports separated by a dash, for example, 4/5-13 for ports 5 to 13 on module 4.
Page 97: Set Port Trap
Chapter 2 Avaya P330 Layer 2 CLI Commands set port trap User level: privileged, supervisor. Use the set port trap command to enable or disable generic SNMP uplink or downlink traps from a port. The syntax for this command is: set port trap <module>/<port>...
Page 98: Set Port Vlan-Binding-Mode
Chapter 2 Avaya P330 Layer 2 CLI Commands Example: To set VLAN 850 to include ports 4 through 7 on module 3. P330-N# set port vlan 850 3/4-7 VLAN 850 modified. VLAN Mod/Ports ---- ----------------------- 3/4-7 set port vlan-binding-mode User level: privileged, supervisor.
Page 99: Set Powerinline External Power
Chapter 2 Avaya P330 Layer 2 CLI Commands set powerinline external power User level: privileged, supervisor. This command is available on P333T-PWR switches only. Use the set powerinline external power command to set the maximum power available from the external power supply to power DTEs.
Page 100: Set Ppp Baud-Rate
Chapter 2 Avaya P330 Layer 2 CLI Commands set ppp baud-rate User level: privileged, supervisor. Defines the baud rate used in PPP sessions. The peer baud rate must be set at the same value as the host. The syntax for this command is: set ppp baud-rate <9600|19200|38400>...
Page 101: Set Psu Type
Use the set psu type command to set the main power supply type (AC/DC) of the module. This command is not applicable to P330-ML switches, which determine the PSU type automatically. This command is used to set the power supply types for other P330 switches in the stack.
Page 102: Set Queuing Scheme
Use the set queuing scheme command to set the queuing scheme to either strict or weighted round robin and to set the weights. If this command is to be implemented on a P330-ML switch other than the stack master, a session should be opened to the relevant switch.
Page 103: Set Radius Authentication Retry-Number
Chapter 2 Avaya P330 Layer 2 CLI Commands set radius authentication retry-number User level: supervisor Sets the number of times an access request is sent when there is no response. The syntax for this command is: set radius authentication retry-number <number>...
Page 104: Set Radius Authentication Server
Chapter 2 Avaya P330 Layer 2 CLI Commands set radius authentication server User level: supervisor Sets the IP address (and shared secret) of the primary or secondary RADIUS Authentication server. The syntax for this command is: set radius authentication server <ip-addr> {primary |...
Page 105: Set Secure Mac
User level: privileged, supervisor. This command is not applicable to the P330-ML switches, hence a session should be opened to the relevant P330 switch in order to execute this command. Use the set self-loop-discovery Admin_Status command to enable or disable IBM token ring cables discovery feature at the module level.
Page 106: Set Snmp Community
User level: privileged, supervisor. Use the set snmp retries command to set the number of retries initiated by the P330 Manager when it tries to send SNMP messages to the switch. The syntax for this command is: set snmp retries <number>...
Page 107: Set Snmp Timeout
User level: privileged, supervisor. Use the set snmp timeout command to set the SNMP timeout in seconds. This command is useful for access using the P330 Manager. The syntax for this command is: set snmp timeout <number>...
Page 108: Set Snmp Trap Auth
Chapter 2 Avaya P330 Layer 2 CLI Commands Example: To enable SNMP ConfigChange traps to a specific manager: P330-N# set snmp trap 192.168.173.42 enable config SNMP config change traps enabled. Example: To enable all traps to a specific manager: P330-N# set snmp trap 192.168.173.42 enable all SNMP all traps enabled.
Page 109: Set Spantree Default-Path-Cost
Chapter 2 Avaya P330 Layer 2 CLI Commands set spantree default-path-cost User level: privileged, supervisor. Use the set spantree default-path-cost command to set the version of the spanning tree default path costs that are to be used by this bridge.
Page 110: Set Spantree Forward-Delay
Chapter 2 Avaya P330 Layer 2 CLI Commands The syntax for this command is: set spantree enable Example: P330-N# set spantree enable bridge spanning tree enabled. set spantree forward-delay User level: privileged, supervisor. Use the set spantree forward-delay command to set the bridge forward delay time parameter.
Page 111: Set Spantree Max-Age
Chapter 2 Avaya P330 Layer 2 CLI Commands set spantree max-age User level: privileged, supervisor. Use the set spantree max-age command to set the bridge spanning tree max age parameter. The syntax for this command is: set spantree max-age <seconds>...
Page 112: Set Spantree Tx-Hold-Count
Chapter 2 Avaya P330 Layer 2 CLI Commands set spantree tx-hold-count User level: privileged, supervisor. Use the set spantree tx-hold-count command to limit the maximum number of BPDUs transmitted during a hello-time period. The syntax for this command is: set spantree tx-hold-count <rate>...
Page 113: Set System Contact
Chapter 2 Avaya P330 Layer 2 CLI Commands set system contact User level: user, privileged, supervisor Use the set system contact command to set the mib2 system contact MIB variable. The syntax for this command is: set system contact [string] string •...
Page 114: Set System Name
Chapter 2 Avaya P330 Layer 2 CLI Commands set system name User level: privileged, supervisor. Use the set system name command to set the mib2 system name MIB variable. The syntax for this command is: set system name [string] string •...
Page 115: Set Time Protocol
Chapter 2 Avaya P330 Layer 2 CLI Commands set time protocol User level: privileged, supervisor. Use the set time protocol command to set the protocol for use in the system as either SNTP protocol or TIME protocol. The syntax for this command is:...
Page 116: Set Timezone
Chapter 2 Avaya P330 Layer 2 CLI Commands set timezone User level: privileged, supervisor. Use the set timezone command to assign a timezone name and sets the time difference of the device relative to the Coordinated Universal Time (UTC / GMT).
Page 117: Set Vlan
Chapter 2 Avaya P330 Layer 2 CLI Commands set vlan User level: privileged, supervisor. Use the set vlan command to configure VLANs. The syntax for this command is: set vlan <vlan-id> [name <vlan-name>] vlan-id vlan number vlan-name vlan name Example: P330-N# set vlan 3 name gregory VLAN id 3, vlan-name gregory created.
Page 118: Set Welcome Message
Chapter 2 Avaya P330 Layer 2 CLI Commands set welcome message User level: privileged, supervisor. Use the set welcome message command to set a welcome message to appear after a reboot or after opening a new session (see session command) in the stack.
Page 119: Show Allowed Managers Table
Chapter 2 Avaya P330 Layer 2 CLI Commands show allowed managers table User level: user, privileged, supervisor Use the show allowed managers table to display the list of the twenty possible allowed managers IP addresses. The syntax for this command is:...
Page 120: Show Arp-Tx-Interval
Use the show autopartition command to display the automatic partition. Autopartition for the P330-ML switches will always have the value disabled. This command is used to display the autopartition status for the other P330 switches in the stack. The syntax for this command is:...
Page 121: Show Boot Bank
Chapter 2 Avaya P330 Layer 2 CLI Commands show boot bank User level: user, privileged, supervisor This command is not supported by the P333R and P333R-LB switches. Use the show boot bank command to display the software bank from which the switch will boot at the next boot process.
Page 122: Show Cascading Fault-Monitoring
Chapter 2 Avaya P330 Layer 2 CLI Commands Example: (by MAC address) P330-N# show cam mac 00-00-81-01-23-45 Dest MAC/Route Destination Ports -------------- ----------------- 00-00-81-01-23-45 00-00-81-01-23-46 Total Matching CAM Entries = 2 Example: (by Module/Port) P330-N>show cam 1/1 show cam 1/1...
Page 123: Show Copy Status
: No-warning show dev log file User level: user, privileged, supervisor This command applies the P330-ML switches only. Use the show dev log file command to display the encrypted device’s log file. The syntax for this command is: show dev log file Example: P330-N>show dev log file...
Page 124: Show Device-Mode
User level: user, privileged, supervisor Use the show device-mode command to show the current P330-ML or P333R operating mode. Possible modes are Router, or Layer 2. This command is not avaliable to the P333T, P334T, P332MF and P333T-PWR switches which do not have Router and to P333R-LB which is always in Load- Balancing mode.
Page 125 Chapter 2 Avaya P330 Layer 2 CLI Commands The syntax for this command is: show download status [slot] Example: P330-N>show download status 1 Bank Download State Activity Status Download Size ----- ------ --------------- ---------------- --------------- Bank B idle Download idle...
Page 126: Show Erase Status
Chapter 2 Avaya P330 Layer 2 CLI Commands show erase status User level: user, privileged, supervisor Use the show erase status command to view the status of the erase configuration operation. The syntax for this command is: show erase status...
Page 127: Show Intelligent-Multicast Hardware-Support
Chapter 2 Avaya P330 Layer 2 CLI Commands show intelligent-multicast hardware-support User level: user, privileged, supervisor Use the show intelligent-multicast hardware-support command to display the intelligent multicast hardware support configuration. The syntax for this command is: show intelligent-multicast hardware-support Example: P330-N>show intelligent-multicast hardware support...
Page 128: Show Intermodule Port Redundancy
(Maximum, Minimum, or Medium) of the Receive (Rx) buffer allocated to each port of the specified switch. Internal buffering for the P330-ML switches will always have the value Not supported. This command is used to display the internal buffering status for...
Page 129: Show Ip Access-Group
Chapter 2 Avaya P330 Layer 2 CLI Commands show ip access-group User level: privileged, supervisor. Use the show ip access-group command to display the active policy-list number. This command applies to the P334T-ML only when it is in device mode "Layer2".
Page 130: Show Ip Access-List-Dscp
Chapter 2 Avaya P330 Layer 2 CLI Commands Example: P330-N>show ip access-list-details 101 Trust configuration is trust-cos DSCP Action Precedence Name ---- -------------------- ---------- ------------ fwd0 mandatory DSCP#0 fwd0 mandatory DSCP#1 fwd0 mandatory DSCP#2 fwd0 mandatory DSCP#3 fwd0 mandatory DSCP#4...
Page 131: Show Ip Access Lists
Chapter 2 Avaya P330 Layer 2 CLI Commands Example: P330-N>show ip access-list-dscp 101 Trust configuration is trust-cos DSCP Action Precedence Name ---- -------------------- ---------- ------------ fwd0 mandatory DSCP#0 fwd0 mandatory DSCP#1 fwd0 mandatory DSCP#2 fwd0 mandatory DSCP#3 fwd0 mandatory DSCP#4...
Page 132: Show Ip Access-List-Summary
Chapter 2 Avaya P330 Layer 2 CLI Commands show ip access-list-summary User level: user, privileged, supervisor This command applies to the P334T-ML only when it is in device mode "Layer2". Use the show ip access-list-summary command to display a summary of policy lists.
Page 133: Show L2-Module-Config
Chapter 2 Avaya P330 Layer 2 CLI Commands show l2-module-config User level: user, privileged, supervisor Use the show l2-module-config command to display Layer 2 module configuration. The syntax for this command is: show l2-module-config A shortened example is shown below: the full output shows information on all the ports.
Page 134 Chapter 2 Avaya P330 Layer 2 CLI Commands set port edge admin state 1/1 non-edge-port set port edge admin state 1/2 non-edge-port set port edge admin state 1/3 non-edge-port set port edge admin state 1/4 non-edge-port set port edge admin state 1/5 non-edge-port...
Page 135 Chapter 2 Avaya P330 Layer 2 CLI Commands !#*************** port 1/2 configuration ***************** !# Port type: 10/100Base-T !# Link status: fail !# STA status: Blocking !#******************************************************** set port disable 1/2 set port negotiation 1/2 enable set port flowcontrol all 1/2 off...
Page 136 Chapter 2 Avaya P330 Layer 2 CLI Commands !#Set vlan table management parameters set port vlan-binding-mode 1/1 static set port vlan-binding-mode 1/2 static set port vlan-binding-mode 1/3 static set port vlan-binding-mode 1/4 static set port vlan-binding-mode 1/5 static set port vlan-binding-mode 1/6 static...
Page 137: Show L2-Stack-Config
Chapter 2 Avaya P330 Layer 2 CLI Commands show l2-stack-config User level: user, privileged, supervisor Use the show l2-stack-config command to display Layer 2 stack configuration. The syntax for this command is: show l2-stack-config Example: Router-N> show l2-stack-config P330-1# !#...
Page 138 Chapter 2 Avaya P330 Layer 2 CLI Commands !# The snmp community strings set snmp community read-only "public" set snmp community read-write "public" set snmp community trap "public" !# Set the ip route addresses set ip route 0.0.0.0 149.49.54.1 set system location ""...
Page 139: Show License
Chapter 2 Avaya P330 Layer 2 CLI Commands !#Set PPP management parameters !#set interface ppp 0.0.0.0 0.0.0.0 --type q to quit or space key to continue-- #set interface ppp disable set ppp authentication incoming none set ppp incoming timeout 0...
Page 140: Show Log
CLI timeout is 10 minutes show mac-aging User level: user, privileged, supervisor This command is available on P330-ML switches only. Use the show mac-aging command to display the current status of the MAC aging function. The syntax for this command is:...
Page 141: Show Mac-Aging-Time
P330-N>show mac-aging mac aging application is disabled show mac-aging-time User level: user, privileged, supervisor This command is available on P330-ML switches only. Use the show mac-aging-time command to display the MAC aging time in minutes. The syntax for this command is:...
Page 142: Show Module-Identity
Chapter 2 Avaya P330 Layer 2 CLI Commands Example: P330-N>show module Type Statuses --- ------------------ ---- -------- ---------------------------- P333T 4144162 PS:OK Fans:OK Mode:Layer2 X330GT2 P330STK Conn-Up:Fail Conn-Down:Ok BUPS BUPS:Not Prsnt Fans:None Type:None P333T-PWR 4455428 PS:OK Fans:OK Mode:Layer2 No Expansion Not Present...
Page 143: Show Port
Chapter 2 Avaya P330 Layer 2 CLI Commands show port User level: user, privileged, supervisor Use the show port command to display port status. The syntax for this command is: show port [<mod_num>[/port_num]] mod_num Number of the switch. If you do not specify a number, the ports (Optional) on all the switches are shown.
Page 144: Show Port Auto-Negotiation-Flowcontrol-Advertisement
User level: user, privileged, supervisor This command is not available on P330-ML switches. If this command is to be implemented on a switch other than the stack master, a session should be opened to the relevant switch.
Page 145 Chapter 2 Avaya P330 Layer 2 CLI Commands Example: P330-N>show port blocking +-------------------+ | Port | Blk /Fwd +-------------------+ 1 | Blocking 2 | Blocking 3 | Blocking 4 | Blocking 5 | Blocking 6 | Blocking 7 | Blocking...
Page 146: Show Port Channel
Chapter 2 Avaya P330 Layer 2 CLI Commands show port channel User level: user, privileged, supervisor Use the show port channel command to display Link Aggregation Group (LAG) information for a specific switch or port. The syntax for this command is: show port channel [<mod_num>[/<port_num>]] [info]...
Page 147: Show Port Classification
Chapter 2 Avaya P330 Layer 2 CLI Commands show port classification User level: privileged, supervisor. Use the show port classification command to display a port’s classification. The syntax for this command is: show port classification [module/[port]] module Number of the switch. If you do not specify a number, the ports on all the switches are shown.
Page 148: Show Port Dot1X
Chapter 2 Avaya P330 Layer 2 CLI Commands show port dot1x User level: user, privileged, supervisor Use the show port dot1x command to display all the configurable values associated with the authenticator port access entity (PAE) and backend authenticator. The syntax for this command is: show dot1x [mod]/[port] Number of the module.
Page 149 ReAuth Period The time, in seconds, after which the port connection should be reauthenticated. Server Tmout The amount of time, in seconds, the P330 waits for a response from the RADIUS server. Supp Tmeout The amount of time, in seconds, before resending authentication requests.
Page 150: Show Port Dot1X Statistics
Chapter 2 Avaya P330 Layer 2 CLI Commands Max Req The maximum number of times a request for authentication is sent before timing out. show port dot1x statistics User level: user, privileged, supervisor Use the show port dot1x statistics command to display all the port dot1x statistics.
Page 151: Show Port Edge State
Chapter 2 Avaya P330 Layer 2 CLI Commands show port edge state User level: privileged, supervisor. Use the show port edge state command to show a port’s edge admin and operational RSTP state. A port can be set to admin state of edge port, but if a BPDU is received on this port the oper state is changed to non-edge state.
Page 152 Chapter 2 Avaya P330 Layer 2 CLI Commands Output Fields Field Description Port Module and port number Send- Send flow-control administration. Possible settings: Flowcontrol- • ON indicates that the local port is allowed to send flow Admin control frames to the far end.
Page 153: Show Port Mirror
Chapter 2 Avaya P330 Layer 2 CLI Commands show port mirror User level: user, privileged, supervisor Use the show port mirror command to display mirroring information for the stack. The syntax for this command is: show port mirror Example: P330-N>show port mirror...
Page 154: Show Port Redundancy
Port security for the P330-ML switches will always have the value unknown. This command is used to display the security status for the other P330 switches in the stack. The syntax for this command is: show port security [<module>[/<port>]]...
Page 155: Show Port Self-Loop-Discovery
User level: user, privileged, supervisor This command is not available on P330-ML switches, hence a session should be opened to the relevant P330 switch in order to execute this command. Use the show port self-loop-discovery command to display which port or switch has an enabled IBM Token Ring cable loop-discovery status.
Page 156: Show Port Vlan-Binding-Mode
Chapter 2 Avaya P330 Layer 2 CLI Commands port Number of the port on the switch. If you do not specify a (Optional) number, all the ports on the switch are shown. You can also specify a range of ports separated by a dash, for example, 4/5-13 for ports 5 to 13 on switch 4.
Page 157: Show Powerinline
Chapter 2 Avaya P330 Layer 2 CLI Commands Show powerinline User level: user, privileged, supervisor This command applies to P333T-PWR switches only. Use the show powerinline command to display the current status of the PD inline power on all ports.
Page 158: Show Powerinline Image Version
Chapter 2 Avaya P330 Layer 2 CLI Commands show powerinline image version User level: user, privileged, supervisor This command applies to P33T-PWR switches only. Use the show powerinline image version command to display the current image version of P333T-PWR switches in the stack or a specific switch.
Page 159: Show Ppp Authentication
Chapter 2 Avaya P330 Layer 2 CLI Commands show ppp authentication User level: user, privileged, supervisor Use the show ppp authentication command to display the authentication method used for PPP sessions. The syntax for this command is: show ppp authentication Example: P330-N>show ppp authentication...
Page 160: Show Ppp Configuration
Chapter 2 Avaya P330 Layer 2 CLI Commands show ppp configuration User level: user, privileged, supervisor Use the show ppp configuration command to display the ppp configuration. The syntax for this command is: show ppp configuration Example: P330-N>show ppp configuration...
Page 161: Show Queuing Scheme
Use the show queuing scheme command to display the current queuing scheme settings. If this command is to be implemented on a P330-ML switch other than the stack master, a session should be opened to the relevant switch. The syntax for this command is:...
Page 162: Show Rmon Event
User level: user, privileged, supervisor Use the show rmon event command to show the parameters of an Event entry defined by the rmon event command or using the P330 Manager. The syntax for this command is: show rmon event [<Event Index>]...
Page 163: Show Rmon History
Chapter 2 Avaya P330 Layer 2 CLI Commands show rmon history User level: user, privileged, supervisor Use the show rmon history command to display the most recent RMON history log for a given History Index. The history index is defined using the rmon history command or using an RMON management tool.
Page 164: Show Secure Current
User level: privileged, supervisor. This command is is not available on P330-ML switches. If this command is to be implemented on a switch other than the stack master, a session should be opened to the relevant switch.
Page 165: Show Security Mode
User level: user, privileged, supervisor This command is not available on P330-ML switches, hence a session should be opened to the relevant P330 switch to execute this command. Use the show self-loop-discovery command to display a switch’s IBM token ring cable discovery status.
Page 166 Chapter 2 Avaya P330 Layer 2 CLI Commands If spanning tree is enabled and is set to rapid-spanning-tree version, there is no need to use the Self-loop-discovery feature ; the rapid spanning tree algorithm avoids loops generated by the IBM cabling.
Page 167: Show Snmp
Chapter 2 Avaya P330 Layer 2 CLI Commands show snmp User level: user, privileged, supervisor Use the show snmp command to display SNMP information. The syntax for this command is: show snmp Example: P330-N>show snmp Authentication trap disabled Community-Access Community-String...
Page 168: Show Snmp Retries
User level: user, privileged, supervisor Use the show snmp retries command to display the number of retries initiated by the P330 Manager when it tries to send SNMP messages to the device. The syntax for this command is: show snmp retries Example: P330-N>show snmp retries...
Page 169 Chapter 2 Avaya P330 Layer 2 CLI Commands port Number of the port on the switch. If you do not specify a (Optional) number, all ports on the specified switch are shown. Example: P330-N>show spantree Spanning tree state is enabled...
Page 170 Chapter 2 Avaya P330 Layer 2 CLI Commands Output fields: Field Description Spanning tree Status of whether Spanning-Tree Protocol is enabled or disabled Designated MAC address of the designated spanning-tree root bridge Root Designated Priority of the designated root bridge...
Page 171: Show System
Chapter 2 Avaya P330 Layer 2 CLI Commands Spanning Tree The version of the Spanning Tree default Path Costs that are to Default Path be used by this Bridge. Costs Port Port number State Spanning-tree port state (disabled, inactive, not-connected,...
Page 172: Show Tftp Download Software Status
Chapter 2 Avaya P330 Layer 2 CLI Commands The syntax for this command is: show system Example: Router-N> show system Uptime d,h:m:s ------------------------ 0,2:40:55 System Name System Location System Contact --------------------- ------------------------- ------------------------- P332_version-3.0.5 Alpha LAB Ygdal Naouri Switch MAC address...
Page 173: Show Tftp Upload Status
: (null) Last warning : No-warning show time User level: user, privileged, supervisor Use the show time command to display the current P330 time and timezone. The syntax for this command is: show time Example: P330-N>show time 10:32:34 27 JAN 2000 GMT...
Page 174: Show Timeout
Example: P330-N>show timeout CLI timeout is 10 minutes show timezone User level: user, privileged, supervisor Use the show timezone command to display the current P330 time zone. The syntax for this command is: show timezone Example: P330-N>show timezone Timezone set to 'GMT', offset from UTC is 0 hours...
Page 175: Show Trunk
Chapter 2 Avaya P330 Layer 2 CLI Commands show trunk User level: user, privileged, supervisor Use the show trunk command to display VLAN tagging information for the switch. The syntax for this command is: show trunk [<mod_num>[/<port_num>-<port_num>]] mod_num Number of the switch. If you do not specify a number, all (Optional) switches in the stack are shown.
Page 176: Show Vlan
Chapter 2 Avaya P330 Layer 2 CLI Commands Example: P330-1(super)# show username User account password access-type ------------------------------- -------------------------------- -------- root ***** admin gkohll ***** read-only readwrite ***** read-write show vlan User level: user, privileged, supervisor Use the show vlan command to display the VLANs configured in the stack or switch.
Page 177: Show Web Aux-Files-Url
Chapter 2 Avaya P330 Layer 2 CLI Commands show web aux-files-url User level: user, privileged, supervisor Displays the URL/directory from where the switch can access the Device Manager auxiliary files (for example help files). The syntax for this command is:...
Page 178: Tech
Chapter 2 Avaya P330 Layer 2 CLI Commands The syntax for this command is: sync time Example: P330-N# sync time Time has been distributed. tech Use the tech command to enter tech mode. This command is reserved for service personnel use only.
Page 179: Validate-Group
Chapter 2 Avaya P330 Layer 2 CLI Commands access-type Access type definition - read only, read-write or administrator Example: P330-1(super)# username john password johnny access-type read-write User account added. P330-1(super)# username root password secret access-type read-write ERROR: User account root has always an administrator access type.
Page 180 Chapter 2 Avaya P330 Layer 2 CLI Commands Example: P330-N# validate-group 101 List 101 is valid-in-progress P330-N# validate-group 101 List 101 is valid The validation process may take some time to complete. Avaya P330 Reference Guide...
Page 181: Chapter 3 Avaya P330 Layer 3 Cli Commands
Chapter 3 Avaya P330 Layer 3 CLI Commands This chapter provides all the Layer 3 CLI (Command Line Interface) commands, parameters, and their default values. How the Layer 3 CLI is Organized The commands that make up the Layer 3 CLI are organized alphabetically and according to context.
Page 182: General Commands
Chapter 3 Avaya P330 Layer 3 CLI Commands General Commands User level: privileged, supervisor. If you are at the “privileged” level, you can only access this command in Configure mode. Type configure at the command prompt to enter configure mode.
Page 183: Clear Arp-Cache
Chapter 3 Avaya P330 Layer 3 CLI Commands The syntax for this command is: [no] arp timeout <seconds> seconds The amount of time, in seconds, that an entry remains in the arp cache. Example: To set the arp timeout to one hour:...
Page 184: Clear Fragment
Chapter 3 Avaya P330 Layer 3 CLI Commands clear fragment User level: privileged, supervisor. Use the clear fragment command to restore fragment action database defaults and free all waiting fragments. The syntax for this command is: clear fragment Example: Router-N# clear fragment...
Page 185: Clear Ip Traffic
Chapter 3 Avaya P330 Layer 3 CLI Commands clear ip traffic User level: privileged, supervisor. This command does not apply to the P333R-LB. Use the clear ip traffic command to clear the ip traffic statistics counters. The syntax for this command is:...
Page 186: Configure
Chapter 3 Avaya P330 Layer 3 CLI Commands configure User level: privileged, supervisor. Use the configure command to enter configure mode. The syntax for this command is: configure Example: P330-1(super)# configure Router-N(configure)# copy running-config startup-config User level: privileged, supervisor. Use the copy running-config startup-config command to save the policy and router configurations to the startup configuration file in the NVRAM.
Page 187: Copy Startup-Config Tftp
Chapter 3 Avaya P330 Layer 3 CLI Commands Example: (for Unix): Router-N(super)# copy running-config tftp /folder/p330/ startup.cfg 149.49.100.41 copy startup-config tftp User level: privileged, supervisor. Use the copy startup-config tftp command to upload the policy and router startup configurations to a TFTP server.
Page 188: Erase Startup-Config
Router-N(configure)# event clear event log Use the event log command to display a list of the event messages. The event messages shown are encrypted and are reserved for Avaya use only. The syntax for this command is: event log [<num>]...
Page 189: Event Set
Chapter 3 Avaya P330 Layer 3 CLI Commands Example: Router-N(configure)# event log The following message is for internal use only!!! Z,o(9?+.ig?aDZ_Z0"Dw"ZHlJZZ,300R3333aDZt?(Z Zt?(Z?qDZ?gXZ;z=WZYLd{z5^=}ZHt!Z^YYE Z33D@3D3YDRTDQTD3wZ'E~MZw@T:@T:_@:_QZ~NZz'oYPZw Z,o(9?+.ig?aDZ"Z0"D3"ZHlJZZ,300R3333aDZt?(Z Zt?(Z?qDZ?gXZ;z=WZYLd{z5^=}ZHt!Z^YYE Z33D@3D3YDRTDQTD3wZ'E~MZw@T:@T:_@:_QZ~NZz'oYPZw Z,=H^zNaDZ0Z3D33ZHlJZZ,303"3333aDZ?lUl9ojoiZ Z("""? A\Zlit?ign Z,!AoaDZwZ0Q_D_QZHlJZZ,303w3333aDZgjKZ ZZ}>}N=Z{~/Z5{}^E}Y Done! event set User level: privileged, supervisor. This command applies to the P333R and P333R-LB only.
Page 190: Event Show
Chapter 3 Avaya P330 Layer 3 CLI Commands event show This command applies to the P333R and P333R-LB only. The event show command display the event status. The syntax for this command is: event show Example: Router-N> event show Print...
Page 191: Fragment Size
Chapter 3 Avaya P330 Layer 3 CLI Commands The syntax for this command is: [no] fragment chain <chain-limit> chain-limit The maximum number of fragments that can comprise a single IP packet, from 2 to 2048. The default is 64. Example:...
Page 192: Help
Chapter 3 Avaya P330 Layer 3 CLI Commands Example: Router-N# fragment timeout 30 help User level: user, privileged, supervisor Use the help command to obtain help on CLI commands. The syntax for this command is: help <command> command A specific CLI command or group of commands Example: Router-N>...
Page 193: Icmp In-Echo-Limit
Chapter 3 Avaya P330 Layer 3 CLI Commands Example: Router-N> hostname Marketing Marketing-1 # If you wish to enter a name which includes spaces, you must enclose the entire name in quotation marks, for example “new york”. icmp in-echo-limit User level: privileged, supervisor.
Page 194: Ip Access-Default-Action
Chapter 3 Avaya P330 Layer 3 CLI Commands Example: Router-N(configure)# interface marketing Done! Router-1(config-if:marketing)# If you wish to enter a name which includes spaces, you must enclose the entire name in quotation marks, for example “new york”. ip access-default-action User level: privileged, supervisor.
Page 195: Ip Access-List
Chapter 3 Avaya P330 Layer 3 CLI Commands Example: Router-N(configure)# ip access-group 101 Done! ip access-list User level: privileged, supervisor. Use the ip access list command to create a specific policy rule. The access list contains several of these rules: each rule pertains to the source IP address, the destination IP address, the protocol, the protocol ports (if relevant), and to the ACK bit (if relevant).
Page 196: Ip Access-List-Cookie
Chapter 3 Avaya P330 Layer 3 CLI Commands Example: Router-N# ip access-list 101 23 deny ip any 1.2.0.0 0.0.255.255 ip access-list-cookie User level: privileged, supervisor. Use the ip access-list-cookie command to set the list cookie for a specific policy list.
Page 197: Ip Access-List-Dscp Operation
Chapter 3 Avaya P330 Layer 3 CLI Commands ip access-list-dscp operation User level: privileged, supervisor. Use the ip access-list-dscp operation command to set a DSCP to CoS mapping. On the P334T-ML, the system performs the mapping for only those frames than match an ACL rule with a “permit”...
Page 198: Ip Access-List-Name
Chapter 3 Avaya P330 Layer 3 CLI Commands ip access-list-dscp trust <policy-list-number> {untrusted|trust-cos |trust-dscp} policy-list- A valid id number for a policy list currently defined for the module number (100 - 149) untrusted Forward the packet with priority 0 trust-cos Forward the packet with its original 802.1p priority (default)
Page 199: Ip Access-List-Owner
Chapter 3 Avaya P330 Layer 3 CLI Commands ip access-list-owner User level: privileged, supervisor. Use the ip access-list owner command to set the owner for a specific policy list. The syntax for this command is: ip access-list-owner <policy-list-number> <owner> <policy-list-number>...
Page 200: Ip Default-Gateway
Chapter 3 Avaya P330 Layer 3 CLI Commands To disable relaying of bootp and dhcp requests: Router-N(configure)# no ip bootp-dhcp relay Done! ip default-gateway User level: privileged, supervisor. If you are at the ”privileged” level, you can only access this command in Configure mode.
Page 201: Ip Max-Arp-Entries
Chapter 3 Avaya P330 Layer 3 CLI Commands Example: To turn the ICMP error messages on: Router-N(configure)# ip icmp-errors Done! ip max-arp-entries User level: privileged, supervisor. • If you are at the ”privileged” level, you can only access this command in Configure mode.
Page 202: Ip Max-Route-Entries
Configure mode. Type configure at the command prompt to enter configure mode. The ip max-route-entries command exists for compatibility with Avaya™ P550. There is no limitation on the size of the routing table, except for the amount of available memory.
Page 203: Ip Route
Chapter 3 Avaya P330 Layer 3 CLI Commands hexadecimal The network masks are in hexadecimal format as indicated by the leading 0X. For example, 0XFFFFFF00. Example: To display netmasks in decimal format: Router-N(configure)# ip netmask-format bitcount decimal Done! ip route User level: privileged, supervisor.
Page 204: Ip Routing
Chapter 3 Avaya P330 Layer 3 CLI Commands ip routing User level: privileged, supervisor. If you are at the ”privileged” level, you can only access this command in Configure mode. Type configure at the command prompt to enter configure mode.
Page 205: Ip Unicast Cache Aging
Chapter 3 Avaya P330 Layer 3 CLI Commands source port integer (1 - 65535) destination port integer (1 - 65535) established value of TCP established bit Example: Router-N(configure)# ip simulate 100 192.67.85.12 193.76.54.25 ip unicast cache aging User level: privileged, supervisor.
Page 206: Ip Unicast Cache High-Limit
Chapter 3 Avaya P330 Layer 3 CLI Commands The syntax for this command is: ip unicast cache aging timeout <time> Example: Router-N(configure)# ip unicast cache aging timeout 10 Done! ip unicast cache high-limit If you are at the ”privileged” level, you can only access this command in Configure mode.
Page 207: Ping
Chapter 3 Avaya P330 Layer 3 CLI Commands Use the no ip unicast cache command to return to the default value. The syntax for this command is: [no] ip unicast cache update-timeout interval Example: Router-N(configure)# ip unicast cache update-timeout 600...
Page 208: Prompt-Length
Chapter 3 Avaya P330 Layer 3 CLI Commands Example: to ping the IP number 149.49.48.1 three times: Router-N> ping 149.49.48.1 3 PING 149.49.48.1: 56 data bytes 64 bytes from 149.49.48.1: icmp_seq=0. time=0. ms 64 bytes from 149.49.48.1: icmp_seq=1. time=0. ms 64 bytes from 149.49.48.1: icmp_seq=2.
Page 209: Rmon2 Host
Chapter 3 Avaya P330 Layer 3 CLI Commands Example: Router-N> reset This command will force a switch-over to the master module and disconnect your telnet session. Do you want to continue (y/n) [n]? y Connection closed by foreign host. rmon2 host User level: privileged, supervisor.
Page 210: Rmon2 Protocol-Dist
Chapter 3 Avaya P330 Layer 3 CLI Commands Example: Router-N(configure)# rmon2 matrix Done! rmon2 protocol-dist User level: privileged, supervisor. If you are at the ”privileged” level, you can only access this command in Configure mode. Type configure at the command prompt to enter configure mode if necessary.
Page 211: Rmon2 Filters
Chapter 3 Avaya P330 Layer 3 CLI Commands Example: Router-N(configure)# rmon2 subnets Done! rmon2 filters User level: privileged, supervisor. If you are at the ”privileged” level, you can only access this command in Configure mode. Type configure at the command prompt to enter configure mode if necessary.
Page 212: Rmon2 Protocol-Dir
Chapter 3 Avaya P330 Layer 3 CLI Commands The syntax for this command is: [no]rmon2 auto-learn Example: Router-N(configure)# rmon2 auto-learn Done! rmon2 protocol-dir User level: privileged, supervisor. If you are at the ”privileged” level, you can only access this command in Configure mode.
Page 213: Router Rip
Chapter 3 Avaya P330 Layer 3 CLI Commands The default is disabled. The syntax for this command is: [no] router ospf Example: Router-N(configure)# router ospf Done! Router-N(configure router:ospf)# router rip User level: privileged, supervisor. If you are at the ”privileged” level, you can only access this command in Configure mode.
Page 214: Router Vrrp
Chapter 3 Avaya P330 Layer 3 CLI Commands Example: To enable the srrp: Router-N(configure)# router srrp Done! Router-N(configure router:srrp)# router vrrp User level: privileged, supervisor. If you are at the ”privileged” level, you can only access this command in Configure mode.
Page 215: Set Device-Mode
Use the set device-mode command to change the basic mode of operation of the switch between Router and Layer 2 modes. This command is available on P330-ML and P333R switches only. The syntax for this command is: set device-mode <mode>...
Page 216: Set Policy Type
Chapter 3 Avaya P330 Layer 3 CLI Commands set policy type User level: privileged, supervisor. This command is available on the P334T-ML switch in device mode “Router” only. Use the set policy type command to set whether the P334T-ML module enforces the active policy-list on all packets or only on routed packets (for modules in 'device-mode router').
Page 217: Set Qos Dscp-Name
Chapter 3 Avaya P330 Layer 3 CLI Commands Example: Router-N(configure)# set qos dcsp-cos-map 9-16 fwd3 set qos dscp-name User level: privileged, supervisor. This command applies to the P333R only. If you are at the ”privileged” level, you can only access this command in Configure mode.
Page 218: Set System Contact
The syntax for this command is: set policy source <source> source local or policy server • The default policy source for P330-ML switches is local • The default policy source for P333R and P333R-LB switches is policy-server Example: Router-N# set qos policy-source local...
Page 219: Set System Location
Chapter 3 Avaya P330 Layer 3 CLI Commands set system location User level: user, privileged, supervisor Use the set system location command to set the system location MIB variable The syntax for this command is: set system location [string] string...
Page 220: Set Vlan
Chapter 3 Avaya P330 Layer 3 CLI Commands set vlan User level: privileged, supervisor. If you are at the ”privileged” level, you can only access this command in Configure mode. Type configure at the command prompt to enter Configure mode if necessary.
Page 221: Show Device-Mode
Chapter 3 Avaya P330 Layer 3 CLI Commands show device-mode User level: user, privileged, supervisor This command does not apply to the P333R-LB which is always in “Load Balancing” mode. Use the show device-mode command to show the current switch operating mode.
Page 222: Show Erase Status
Chapter 3 Avaya P330 Layer 3 CLI Commands Example: Router-N> show dscp set qos trust trust-dscp DSCP table validity status: Valid DSCP Action Precedence ApplicStatus ApplicType Name ---- -------------------- ---------- ------------ ------------ ---------- fwd0 mandatory applicable static DSCP #0.0 fwd0...
Page 223: Show Ip Access-Group
Number of packets which overflowed the database is 0 show ip access-group User level: user, privileged, supervisor Use the show ip access-group command to see information about the configured active access list. This command is available on P330-ML switches only. Avaya P330 Reference Guide...
Page 224: Show Ip Access-Lists
Chapter 3 Avaya P330 Layer 3 CLI Commands The syntax for this command is: show ip access-group Example: Router-N> show ip access-group access-group 100 show ip access-lists User level: user, privileged, supervisor Use the show ip access lists command to display all the current policy lists.
Page 225: Chapter 3 Avaya P330 Layer 3 Cli Commands
Chapter 3 Avaya P330 Layer 3 CLI Commands Example: Router-N> show ip access-lists details The current policy source is policy-server default List (0) parameters List 0 is validated - the List was not changed since the last validation List 0 is valid...
Page 226: Show Ip Access-List-Dscp
Chapter 3 Avaya P330 Layer 3 CLI Commands show ip access-list-dscp User level: user, privileged, supervisor Use the show ip access-list-dscp command to display the DSCP to CoS map of a policy-list. The syntax for this command is: show ip access-list-dscp <policy-list-number> [<dscp>]...
Page 227: Show Ip Arp
Chapter 3 Avaya P330 Layer 3 CLI Commands Example: Router-N> show ip access-list-summary The policy lists summary: default List (0) show ip arp User level: user, privileged, supervisor Use the show ip arp command to display the Address Resolution Protocol (ARP) cache.
Page 228: Show Ip Icmp
Chapter 3 Avaya P330 Layer 3 CLI Commands show ip icmp User level: user, privileged, supervisor Use the show icmp ip command to display the status of ICMP error messages. The syntax for this command is: show ip icmp Example: Router-N>...
Page 229: Show Ip Interface Brief
Chapter 3 Avaya P330 Layer 3 CLI Commands Example: Router-N> show ip interface Showing 2 Interfaces mgmt is administratively up On vlan Default Internet address is 10.49.54.14 , subnet mask is 255.255.255.0 Broadcast address is 10.49.54.255 Directed broadcast forwarding is disabled...
Page 230: Show Ip Ospf
Chapter 3 Avaya P330 Layer 3 CLI Commands Example: Router-N> show ip interface brief Showing 1 Interfaces Interface Address Mask Status -------------------- --------------- --------------- -------------------- 149.49.54.56 255.255.255.0 show ip ospf User level: user, privileged, supervisor Use the show ip opsf command to displays general information about OSPF routing.
Page 231: Show Ip Ospf Interface
Chapter 3 Avaya P330 Layer 3 CLI Commands network Displays information only about the network LSAa. Optional. network-summary Displays information only about the network LSAa summary. Optional external Displays information only about the external LSAa. Optional. show ip ospf interface...
Page 232: Show Ip Protocols
Chapter 3 Avaya P330 Layer 3 CLI Commands Example: Router-N> show ip ospf neighbor There are no ospf neighbors If you wish to enter a name which includes spaces, you must enclose the entire name in quotation marks, for example “new york”.
Page 233: Show Ip Reverse-Arp
Chapter 3 Avaya P330 Layer 3 CLI Commands show ip reverse-arp User level: user, privileged, supervisor Use the show ip reverse-arp command to display the IP address of a host, based on a known MAC address. The syntax for this command is: show ip reverse-arp <mac addr>...
Page 234: Show Ip Route Best-Match
Chapter 3 Avaya P330 Layer 3 CLI Commands show ip route best-match User level: user, privileged, supervisor Use the show ip route best-match command to display a routing table for a destination address. The syntax for this command is: show ip route best-match <dst addr>...
Page 235: Show Ip Route Summary
Chapter 3 Avaya P330 Layer 3 CLI Commands show ip route summary User level: user, privileged, supervisor Use the show ip route summary command to display the number of routes known to the switch. The syntax for this command is:...
Page 236: Show Ip Traffic
Chapter 3 Avaya P330 Layer 3 CLI Commands show ip traffic User level: user, privileged, supervisor This command does not apply to the P333R-LB. Use the show ip traffic command to display the IP traffic statistics counters. The syntax for this command is:...
Page 237: Show Ip Unicast Cache
Chapter 3 Avaya P330 Layer 3 CLI Commands Sent: 1311 total, 0 ICMP errors 433 unreachables, 0 time exceeded 0 parameter, 0 quench 17 echo, 861 echo reply 0 timestamps request, 0 timestamp reply 0 mask requests, 0 mask replies...
Page 238: Show Ip Unicast Cache Host
Chapter 3 Avaya P330 Layer 3 CLI Commands src mask The source mask IP address. dst addr The destination IP address. dst mask The destination mask IP address. Example: Router-N> show ip unicast cache Showing 6 Sessions. Source IP Destination IP...
Page 239: Show Ip Unicast Cache Networks
Chapter 3 Avaya P330 Layer 3 CLI Commands show ip unicast cache networks User level: user, privileged, supervisor Use the show ip unicast cache networks command to display a summary of networks handled by the hardware unicast cache database. The syntax for this command is: show ip unicast cache networks [<net addr>...
Page 240: Show Ip Unicast Cache Nexthop
Chapter 3 Avaya P330 Layer 3 CLI Commands Example: Router-N> show ip unicast cache networks detailed 192.168.6.0 24 Showing 3 rows NetworkMask IP Address ============ =================== 192.168.6.0 24 192.168.6.40 192.168.6.53 192.168.6.64 show ip unicast cache nextHop User level: privileged, supervisor.
Page 241: Show Ip Unicast Cache Aging Timeout
Next-Hops : show ip unicast cache aging timeout User level: user, privileged, supervisor This command does not apply to the P330-ML. Use the show ip unicast cache aging timeout command to display aging and update timeout configuration. The syntax for this command is:...
Page 242: Show Ip Vrrp Detail
Chapter 3 Avaya P330 Layer 3 CLI Commands show ip vrrp detail User level: user, privileged, supervisor Use the show ip vrrp detail command to display full VRRP-related information The syntax for this command is: show ip vrrp detail Example: Router-N>...
Page 243: Show Policy Type
Chapter 3 Avaya P330 Layer 3 CLI Commands Virtual Router on VLAN: Router-id: State: BACKUP Priority: Advertisement Interval: Last State Change: 00:00:00 Override Address Ownership Rule: No Authentication Type: None Authentication Key: "" Master IP Address 0.0.0.0 Has 1 IP addresses IP addresses: 192.168.66.24...
Page 244: Show Rmon2 State
Chapter 3 Avaya P330 Layer 3 CLI Commands show rmon2 state User level: user, privileged, supervisor This command applies to the P333R only. Use the show rmon2 state command to show the status of the rmon2 application. The syntax for this command is:...
Page 245: Show Rmon2 Host
Chapter 3 Avaya P330 Layer 3 CLI Commands Example: Router-N# show rmon2 protocol-dist Protocol Total Pkts Zero DSCP Non-0 DSCP ---------------------------- ---------- ---------- ---------- IP over ether2 2689702 2689428 ARP Protocol 314568 ICMP over IP over ether2 201905 TCP over IP over ether2...
Page 246: Show Rmon2 Matrix
Chapter 3 Avaya P330 Layer 3 CLI Commands show rmon2 matrix User level: user, privileged, supervisor Use the show rmon2 matrix command to display RMON2 matrix information. The syntax for this command is: show rmon2 matrix [<SrcIpAddr> [<dstIpAddr>]] SrcIpAddrr Source IP address...
Page 247: Show Rmon2 Auto-Learn
Chapter 3 Avaya P330 Layer 3 CLI Commands Example: Router-N# show rmon2 subnet Subnet Mask InPackets OutPackets --------------- --------------- ---------- ---------- 0.0.0.0 0.0.0.0 16556 16536 192.168.32.0 255.255.255.0 192.168.33.0 255.255.255.0 192.168.34.0 255.255.255.0 192.168.35.0 255.255.255.0 192.168.36.0 255.255.255.0 8389 5224 192.168.37.0 255.255.255.0 192.168.38.0 255.255.255.0...
Page 248: Show Rmon2 Host-Top-N
Chapter 3 Avaya P330 Layer 3 CLI Commands Example: Router-N# show rmon2 filters Index IP Address IP Mask ---------- --------------- --------------------- 192.168.77.5 255.255.255.255 192.168.88.0 255.255.255.0 show rmon2 host-top-n User level: user, privileged, supervisor Use the show rmon2 host-top-n command to display a sorted hosts counters list.
Page 249: Show Rmon2 Protocol-Dist-Top-N
Chapter 3 Avaya P330 Layer 3 CLI Commands Example: Router-N# show rmon2 matrix-top-n ALL show rmon2 protocol-dist-top-n User level: user, privileged, supervisor Use the show rmon2 protocol-dist-top-n command to display a sorted applications counters list. The syntax for this command is:...
Page 250: Show Startup-Config
Use the show startup-config command to show configuration loaded at startup. The syntax for this command is: show startup-config Example: Router-N> show startup-config ! Avaya Inc. P333R Switch - Router configuration ! version 4.0.5 hostname "R1-Backup" interface "net" ip vlan name "Default" ip address 149.49.54.56 255.255.255.0...
Page 251: Show Tftp Download Status
Chapter 3 Avaya P330 Layer 3 CLI Commands show tftp download status User level: user, privileged, supervisor Use the show tftp download status commands to display the status of the current TFTP configuration download process into the device. The syntax for this command is:...
Page 252: Show Vlan
Chapter 3 Avaya P330 Layer 3 CLI Commands show vlan User level: user, privileged, supervisor Use the show vlan command to display router Layer 3 interfaces. The syntax for this command is: show vlan Example: Router-N> show vlan VLAN NAME...
Page 253: Validate-Group
Chapter 3 Avaya P330 Layer 3 CLI Commands validate-group User level: privileged, supervisor. Use the validate-group command to verify that all the rules in a policy list are valid. If there is a configuration problem with a specific rule, or with a number of rules, detailed error messages will be given.
Page 254: Interface Context
Chapter 3 Avaya P330 Layer 3 CLI Commands Interface Context You can only access these commands in the “interface” context. Type interface [name] at the command prompt to enter the “interface” context if necessary. default-metric User level: privileged, supervisor. Use the default metric command to set the interface RIP route metric.
Page 255: Ip Address
Chapter 3 Avaya P330 Layer 3 CLI Commands ip address User level: privileged, supervisor. Use the ip address command to assign an IP address and mask to an interface. The syntax for this command is: ip address <ip-address> <mask> [<admin-state>] ip address The IP address assigned to the interface.
Page 256: Ip Bootp-Dhcp Network
Chapter 3 Avaya P330 Layer 3 CLI Commands ip bootp-dhcp network User level: privileged, supervisor. Use the ip bootp-dhcp network command to configure the network from which the BOOTP/DHCP server shall allocate an address. Use the no ip bootp-dhcp network command to remove a network.
Page 257: Ip Broadcast-Address
Chapter 3 Avaya P330 Layer 3 CLI Commands Example: To add station 192.168.37.46 as a bootp/dhcp server to handle bootp/dhcp requests arriving at the interface “marketing”: Router-N(configure-if:marketing) # ip bootp-dhcp server 192.168.37.46 Done! ip broadcast-address User level: privileged, supervisor. Use the ip broadcast command to update the interface broadcast address. The Broadcast address must be filled in with 0s (zeros) or 1s (ones).
Page 258: Ip Netbios-Rebroadcast
Chapter 3 Avaya P330 Layer 3 CLI Commands ip netbios-rebroadcast User level: privileged, supervisor. Use the ip netbios-rebroadcast command to set the NETBIOS rebroadcasts mode on an interface. Use the no ip netbios-rebroadcast command to disable NETBIOS rebroadcasts on an interface.
Page 259: Ip Ospf Cost
Chapter 3 Avaya P330 Layer 3 CLI Commands ip ospf cost User level: privileged, supervisor. Use the ip ospf command to configure interface metric. Use the no ip ospf cost command to set the cost to its default. The default is 1.
Page 260: Ip Ospf Priority
Chapter 3 Avaya P330 Layer 3 CLI Commands The syntax for this command is: [no] ip ospf hello-interval <seconds> seconds integer Example: Router-N(configure-if:marketing) # ip ospf hello-interval 5 Done! ip ospf priority User level: privileged, supervisor. Use the ip ospf priority command to configure interface priority used in DR election.
Page 261: Ip Redirects
Chapter 3 Avaya P330 Layer 3 CLI Commands ip redirects User level: privileged, supervisor. Use the ip redirects command to enables the sending of redirect messages on the interface. Use the no ip redirect command to disable the redirect messages. By default, sending of redirect messages on the interface is enabled.
Page 262: Ip Rip Authentication Mode
Chapter 3 Avaya P330 Layer 3 CLI Commands ip rip authentication mode User level: privileged, supervisor. Use the ip rip authentication command to specify the type of authentication used in RIP Version 2 packets. Use the no ip rip authentication command to restore the default value of none.
Page 263: Ip Rip Poison-Reverse
Chapter 3 Avaya P330 Layer 3 CLI Commands Example: Router-N(configure-if:marketing) # ip rip default-route- mode talk listen Done! ip rip poison-reverse User level: privileged, supervisor. You can only access this command in interface mode. Type interface [name] at the command prompt to enter interface mode if necessary.
Page 264: Ip Rip Send-Receive-Mode
Chapter 3 Avaya P330 Layer 3 CLI Commands The possible versions of the RIP packets received and sent on an interface are: RIP Version 1 packets RIP Version 2 packets. Example: To specify that RIP version 2 should be running on the basis of the interface “marketing”:...
Page 265: Ip Rip Split-Horizon
Chapter 3 Avaya P330 Layer 3 CLI Commands ip rip split-horizon User level: privileged, supervisor. Use the ip rip split-horizon command to enable split-horizon mechanism. Use the no ip rip split-horizon command to disable the split-horizon. By default split-horizon is enabled.
Page 266: Ip Srrp Backup
Chapter 3 Avaya P330 Layer 3 CLI Commands ip srrp backup User level: privileged, supervisor. Use the ip srrp backup command to backup an additional interface of the main router using the SRRP application. If the main router fails, the switch takes over its activities on all configured interfaces.
Page 267: Ip Vrrp
Chapter 3 Avaya P330 Layer 3 CLI Commands ip vrrp User level: privileged, supervisor. Use the ip vrrp command to create a virtual router on the interface. Use the no ip vrrp command to delete a virtual router. The syntax for this command is: [no] ip vrrp <vr-id>...
Page 268: Ip Vrrp Auth-Key
Chapter 3 Avaya P330 Layer 3 CLI Commands ip vrrp auth-key User level: privileged, supervisor. Use the ip vrrp auth-key command to set the virtual router simple password authentication for the virtual router ID. Use the no ip vrrp auth-key command to disable simple password authentication for the virtual router instance.
Page 269: Ip Vrrp Preempt
Chapter 3 Avaya P330 Layer 3 CLI Commands ip vrrp preempt User level: privileged, supervisor. Use the ip vrrp preempt command to configure the router to preempt a lower priority master for the virtual router ID. Use the no ip vrrp preempt command to disable preemption for the virtual router instance.
Page 270: Ip Vrrp Priority
Chapter 3 Avaya P330 Layer 3 CLI Commands ip vrrp priority User level: privileged, supervisor. Use the ip vrrp priority command to set the virtual router priority value used when selecting a master router. Use the no ip vrrp priority command to restore the default value.
Page 271: Router Rip Context
Chapter 3 Avaya P330 Layer 3 CLI Commands Router RIP Context You can only access these commands in the “Router-RIP” context. Type router rip at the command prompt to enter the “Router-RIP” context if necessary. network User level: privileged, supervisor.
Page 272: Timers Basic
Chapter 3 Avaya P330 Layer 3 CLI Commands Example: Router-N(configure router:rip)# redistribute ospf Done! timers basic User level: privileged, supervisor. Use the timers basic command to configure the route timer. Use the no timers basic command to restore the timers to their default values.
Page 273: Router Ospf Context
Chapter 3 Avaya P330 Layer 3 CLI Commands Router OSPF Context You can only access these command in the “Router-OSPF” context. Type router ospf at the command prompt to enter the “Router -OSPF” context if necessary. area User level: privileged, supervisor.
Page 274: Passive-Interface
Chapter 3 Avaya P330 Layer 3 CLI Commands area id Area ID. This parameter exists for compatibility with P550. Example: Router-N(configure router:ospf)# network 192.168.0.0 Router-N(configure router:ospf)# area 192.168.0.0 0.0.255.255 area 0.0.0.0 passive-interface User level: privileged, supervisor. Use the passive interface command to allow interfaces to be flooded into the OSPF domain as OSPF routes and not external routes.
Page 275: Timers Spf
Chapter 3 Avaya P330 Layer 3 CLI Commands Example: Router-N(configure router:ospf)# redistribute static timers spf User level: privileged, supervisor. Use the timers spf command to configure the delay between runs of OSPF’s SPF calculation. Use the no form of this command to restore the default (3 seconds).
Page 276: Router Srrp Context
Chapter 3 Avaya P330 Layer 3 CLI Commands Router SRRP Context You can only access these commands in the “Router-SRRP” context. Type router srrp at the command prompt to enter the “Router -SRRP” context if necessary. poll-interval User level: user, privileged, supervisor Use the poll-interval command to configure the polling interval in seconds used by SRRP.
Page 277: Chapter 4 Load Balancing Cli Commands
Load Balancing CLI Commands This chapter provides all load balancing CLI commands, parameters and their default values. Not all groups, parameters and commands are available when P330 boots up from its INIT software. You can use the load balancing commands available from the Router-N # prompt.
Page 278: Ar-Filter Commands
A name, with up to 32 characters, a service ID (an integer from 1 to 1024), or no-ar. uni-directional The ar-filter is applied in the direction from the source to the destination. bi-directional The ar-filter is applied in both directions. Avaya P330 Reference Guide...
Page 279: Ar-Filter-Admin-Status
Use the show ar-filter command to display all AR filters. The syntax for this command is: show ar-filter [<id>] The identification number of the AR filter, an integer from 1 to 1024. Example: Router-N> show ar-filter 1 Avaya P330 Reference Guide...
Page 280: Show Ar-Filter Details 1
Use the lb control ar command to enable Application Redirection (AR). Use the no form of this command to disable AR. The syntax for this command is: [no] lb control ar Example: Router-N(configure)# lb control ar Avaya P330 Reference Guide...
Page 281: Lb Control Fwlb
VLAN-area of AR real servers, it is load-balanced. This allows load balanced packets to first go through the AR real-servers, and afterwards be load-balanced as SLB packets. • slb-prior-to-ar Cache redirection is never applied on SLB packets. Example: Router-N(configure)# lb control precedence ar-prior-to-slb Avaya P330 Reference Guide...
Page 282: Lb Control Slb
Use the show lb real-ar-server cache command to display the LB real AR server cache. The syntax for this command is: show lb real-ar-server cache [server] server The IP address of the real server. Example: Router-N> show lb real-ar-server cache 10.1.1.1 Avaya P330 Reference Guide...
Page 283: Show Lb Real-Ar-Server Cache Details 10.1.1.1
LB real bridging firewall cache. The syntax for this command is: show lb real-bridging-fw cache details [server] server The IP address of the real server. Example: Router-N> show lb real-bridging-fw cache details 10.1.1.1 Avaya P330 Reference Guide...
Page 284: Show Lb Real-Routing-Fw Cache
LB real routing firewall cache. The syntax for this command is: show lb real-routing-fw cache details [server] server The IP address of the real server. Example: Router-N> show lb real-routing-fw cache details 10.1.1.1 Avaya P330 Reference Guide...
Page 285: Show Lb Real-Slb-Server Cache 10.1.1.1
Use the show lb virtual-server cache command to display the LB virtual server cache. The syntax for this command is: show lb virtual-server cache [<virtual server name>] virtual server name The name of the virtual server, a string of up to 80 characters. Avaya P330 Reference Guide...
Page 286: Show Lb Virtual-Server Cache Details
The syntax for this command is: show lb virtual-server cache details [<virtual server name>] virtual server name The name of the virtual server, a string of up to 80 characters. Example: Router-N> show lb virtual-server cache details vServer1 Avaya P330 Reference Guide...
Page 287: Health Check Commands
The domain name for the Health Check to retrieve from - a string up to 255 characters. Example: Router-N(super-hc-http:7)# domain www.avaya.com To define a name that includes spaces, enclose the entire name in quotation marks (e.g., "new york"). Avaya P330 Reference Guide...
Page 288: Hc Http Expected-String
The syntax for this command is: [no] expected-string-offset <offset> offset The offset of the Health Check’s expected string, an integer from 0 - 1000. Example: Router-N(super-hc-http:7)# expected-string-offset 5 Avaya P330 Reference Guide...
Page 289: Hc Http Method
= 0. The syntax for this command is: port <port number> port number The port number used to open an HTTP session, an integer from 0 - 65535. Example: Router-N(super-hc-http:7)# port 65 Avaya P330 Reference Guide...
Page 290: Hc Http Success-Response
("/"). The syntax for this command is: [no] url <url> The URL for the Health Check to retrieve from the server - a string up to 255 characters. Example: Router-N(super-hc-http:7)# url /index.html Avaya P330 Reference Guide...
Page 291: Hc Http Version
Use the hc script command to create/enter the Script Health Check context. The syntax for this command is: hc script <hc-id> hc-id The index number of the Health Check, an integer up to 32. Example: Router-N(super)# hc script 3 Avaya P330 Reference Guide...
Page 292: Hc Script Expected-String
(the Virtual Service port). You achieve the same result by entering the hc script port command with no port number, or with port number = 0. Avaya P330 Reference Guide...
Page 293: Hc Script Query
The syntax for this command is: hc tcp-connect <hc-id> [<port>] hc-id The index number of the Health Check, an integer up to 32. port The port number used to open a TCP session, an integer between 0 and 65535. Avaya P330 Reference Guide...
Page 294: Show Hc
User level: user, privileged, supervisor Use the show hc last response command to show the last data response of a HTTP or Script Health Check. This assists in verifying the correct offset or contents of an expected string. Avaya P330 Reference Guide...
Page 295 <type> <service-name> <rip> type The type of service: SLB or AR. service-name The name of the service - a string up to 32 characters. The IP address. Example: Router-N> show hc last response slb avaya7 10.1.1.3 Avaya P330 Reference Guide...
Page 296: Proxy Ip (Pip) Commands
User level: privileged, supervisor Use the pip-bank command to configure a PIP. The syntax for this command is: pip-bank <bank-id> bank-id The index number of the PIP, an integer up to 64. Example: Router-N(super)# pip-bank 12 Avaya P330 Reference Guide...
Page 297: Show Pip-Bank
Router-N> show pip-bank 1 show pip-bank details User level: user, privileged, supervisor Use the show pip-bank details command to display details for all PIPs. The syntax for this command is: pip-bank details Example: Router-N> show pip-bank details Avaya P330 Reference Guide...
Page 298: Real Ar Server Commands
Use the admin-status command to set the administrative status to enable or disable. The syntax for this command is: admin-status <enable | disable> enable Set admin status to enable. disable Set admin status to disable. Example: Router-N(configure)# admin-status enable Avaya P330 Reference Guide...
Page 299: Real-Ar-Server Backup
(5 seconds). The syntax for this command is: [no] hc interval <time-sec> time-sec The amount of time in seconds, an integer from 1 to 36. Avaya P330 Reference Guide...
Page 300: Real-Ar-Server Hc Success-Retries
AR server is considered to have "timed out" to the default (1 second). The syntax for this command is: [no] hc timeout <time-sec> The amount of time in seconds, an integer. time-sec Example: Router-N(configure)# hc timeout 10 Avaya P330 Reference Guide...
Page 301: Real-Ar-Server Weight
Use the show real-ar-server details command to display the full details of a real server using AR. The syntax for this command is: show real-ar-server details [<server-ip>] The IP address of the real server. server-ip Example: Router-N> show real-ar-server details 10.1.1.2 Avaya P330 Reference Guide...
Page 302: Real Slb Server Commands
Use the admin-status command to set the administrative status to enable or disable. The syntax for this command is: admin-status <enable | disable> enable Set admin status to enable. disable Set admin status to disable. Example: Router-N(configure)# admin-status enable Avaya P330 Reference Guide...
Page 303: Real-Slb-Server Backup
(the number of times the real SLB server should be health-checked before determining failure) to the default (4). The syntax for this command is:Syntax [no] hc failure-retries <failure-retries> failure-retries The number of times, an integer from 1 to 32. Avaya P330 Reference Guide...
Page 304: Real-Slb-Server Hc Interval
(1). The syntax for this command is: [no] hc success-retries <success-retries> success-retries The number of times, an integer from 1 to 32. Example: Router-N(configure)# hc success-retries 10 Avaya P330 Reference Guide...
Page 305: Real-Slb-Server Hc Timeout
User level: user, privileged, supervisor Use the show real-slb-server command to display all real servers using SLB. The syntax for this command is: show real-slb-server [<server-ip>] server-ip The IP address of the real server. Example: Router-N> show real-slb-server 10.1.1.2 Avaya P330 Reference Guide...
Page 306: Show Real-Slb-Server Details
Use the show real-slb-server details command to display the full details of a real server using SLB. The syntax for this command is: show real-slb-server details [<server-ip>] server-ip The IP address of the real server. Example: Router-N> show real-slb-server details 10.1.1.2 Avaya P330 Reference Guide...
Page 307: Real Bridging Fw Commands
Use the admin-status command to set the administrative status to enable or disable. The syntax for this command is: admin-status <enable | disable> enable Set admin status to enable. disable Set admin status to disable. Example: Router-N(configure)# admin-status enable Avaya P330 Reference Guide...
Page 308: Real-Bridging-Fw Backup
(5 seconds). The syntax for this command is: [no] hc interval <time-sec> time-sec The amount of time in seconds, an integer from 1 to 36. Avaya P330 Reference Guide...
Page 309: Real-Bridging-Fw Hc Success-Retries
"timed out". Use the no form of this command to set the time-out to the default value (1 second). The syntax for this command is: [no] hc timeout <time-sec> time-sec The amount of time in seconds, an integer. Example: Router-N(configure)# hc timeout 10 Avaya P330 Reference Guide...
Page 310: Real-Bridging-Fw Weight
Use the show real-bridging-fw details command to display the full details of a real firewall using Bridging FWLB. The syntax for this command is: show real-bridging-fw details [<server-ip>] server-ip The IP address of the real server. Example: Router-N(configure)# show real-bridging-fw details 10.1.1.2 Avaya P330 Reference Guide...
Page 311: Real Routing Fw Commands
Use thereal-routing-fw admin-status command to set the administrative status to enable or disable. The syntax for this command is: admin-status <enable|disable> enable Set admin status to enable. disable Set admin status to disable. Example: Router-N(configure)# admin-status enable Avaya P330 Reference Guide...
Page 312: Real-Routing-Fw Backup
(4). The syntax for this command is: [no] hc failure-retries <failure-retries> failure-retries The number of times, an integer from 1 to 32. Example: Router-N(configure)# hc failure-retries 10 Avaya P330 Reference Guide...
Page 313: Real-Routing-Fw Hc Interval
(1). The syntax for this command is: [no] hc success-retries <success-retries> success-retries The number of times, an integer from 1 to 32. Example: Router-N(configure)# success-retries 10 Avaya P330 Reference Guide...
Page 314: Real-Routing-Fw Hc Timeout
Use the id command to set an identification number for a real routing firewall. The syntax for this command is: id <r-routing-fw-id> r-routing-fw-id The identification number, an integer from 1 to 1024. Example: Router-N(configure)# id 2 Avaya P330 Reference Guide...
Page 315: Real-Routing-Fw Weight
(10). The syntax for this command is: [no] weight <weight> weight The weight of the real server, an integer from 1 to 256. Example: Router-N(configure)# weight 5 Avaya P330 Reference Guide...
Page 316: Show Real-Routing-Fw
Use the show real-routing-fw details command to display the full details of a real firewall using Routing FWLB. The syntax for this command is: show real-routing-fw details [<server-ip>] The IP address of the real server. server-ip Example: Router-N> show real-routing-fw details 10.1.1.2 Avaya P330 Reference Guide...
Page 317: Rsg (Real Server Group) Commands
Use the admin-status command to set the administrative status of a real server group to enable or disable. The syntax for this command is: admin-status <enable | disable> enable Set admin status to enable. disable Set admin status to disable. Example: Router-N(configure)# admin-status enable Avaya P330 Reference Guide...
Page 318: Rsg Backup
Application Redirection. Use the no form of this command to remove a real AR server from the real-server group. The syntax for this command is: [no] real-ar-server <server-ip> server-ip The IP address of the real server. Example: Router-N(configure)# real-ar-server 10.1.1.2 Avaya P330 Reference Guide...
Page 319: Rsg Real-Bridging-Fw
1024, only relevant for routing firewalls. It is only necessary to add the parameter server-id if the real server group does not yet exist since typing it creates a real server. Example: Router-N(configure)# real-routing-fw 10.1.1.2 5 Avaya P330 Reference Guide...
Page 320: Rsg Real-Slb-Server
Use the show rsg command to display all real server groups. The syntax for this command is: show rsg [<rsg>] The name of the real server group, a string up to 32 characters. Example: Router-N> show rsg rsg1 Avaya P330 Reference Guide...
Page 321: Show Rsg Details
Use the show rsg details command to display the full details of all real server groups. The syntax for this command is: show rsg details [<rsg>] The name of the real server group, a string up to 32 characters. Example: Router-N> show rsg details rsg1 Avaya P330 Reference Guide...
Page 322: General Virtual Service Commands
The name of the real server group, a string of up to 16 characters. src-ip The IP address of the source. src-wildcard The source IP address’s network wildcard. dst-ip The destination IP address. dst-wildcard The destination IP address’s network wildcard. Avaya P330 Reference Guide...
Page 323 Destination IP Real IP --------------- --------------- --------------- 193.170.2.1 10.2.1.10 10.1.1.2 193.170.2.2 10.2.1.10 10.1.1.1 193.170.2.3 10.2.1.10 10.1.1.2 193.170.2.4 10.2.1.10 10.1.1.1 193.170.2.5 10.2.1.10 10.1.1.2 193.170.2.6 10.2.1.10 10.1.1.1 193.170.2.7 10.2.1.10 10.1.1.2 193.170.2.8 10.2.1.10 10.1.1.1 193.170.2.9 10.2.1.10 10.1.1.2 193.170.2.10 10.2.1.10 10.1.1.1 Avaya P330 Reference Guide...
Page 324: Virtual Ar Service Commands
AR services. The syntax for this command is: show virtual-ar-service details [<service>] service The name of the virtual AR service, a string up to 32 characters. Example: Router-N> show virtual-ar-service details ArSrvc1 Avaya P330 Reference Guide...
Page 325: Virtual Ar-Service
Use the no form of this command to set the application to the default (IP-all ports). The syntax for this command is: [no] application <udp | tcp | ip | <protocol>> [<min-v-port> [max-v-port]] protocol An integer, from 0 to255. Avaya P330 Reference Guide...
Page 326: Virtual-Ar-Service Failure-Action
Use the failure-action command to set the failure-action decision when no operating real servers were found. The syntax for this command is: failure-action <forward | drop> forward Forwards the packet. drop Drops the packet. Example: Router-N(configure)# failure-action Avaya P330 Reference Guide...
Page 327: Virtual-Ar-Service Hash-Key
Enables verifying HTTP server functioning by comparing the response from the server with a user-configurable response. script Verifies the functioning of the server by running a script on the server. specific-id The identification number of the health check. Avaya P330 Reference Guide...
Page 328: Virtual-Ar-Service Id
MinMiss distributes sessions to servers in the same way as Hash. However, MinMiss sustains persistency even when a server is removed or added to the server group. For more information on server metrics, see Load Balancing Metrics on page 198. Example: Router-N(configure)# metric round-robin Avaya P330 Reference Guide...
Page 329: Virtual-Ar-Service Persistency
AR service to the default (0.0.0.0). The syntax for this command is: [no] persistency wildcard <wildcard> wildcard The client IP network wildcard. Avaya P330 Reference Guide...
Page 330: Virtual-Ar-Service Rsg
Use the simulate-hash command to predict which Real Server is selected based on packet IP address. The syntax for this command is: simulate-hash <src-IP> src-IP The source IP address of the device. Example: Router-N(configure)# simulate-hash 193.170.1.1 Avaya P330 Reference Guide...
Page 331: Virtual Fw Service Commands
The syntax for this command is: show virtual-fw-service details [<service>] service The name of the virtual firewall service, a string up to 32 characters. Example: Router-N> show virtual-fw-service details Vsrvc1 Avaya P330 Reference Guide...
Page 332: Virtual Fw-Service
Use the admin-status command to set the virtual firewall service administrative status to enable or disable. The syntax for this command is: admin-status <enable | disable> enable Set admin status to enable. disable Set admin status to disable. Example: Router-N(configure)# admin-status enable Avaya P330 Reference Guide...
Page 333: Virtual-Fw-Service Hash-Key
The default, which is the ping health check method. ping Each server is periodically pinged and checked if an answer was received. specific-id The identification number of the health check. Example: Router-N(configure)# hc ping 1 Avaya P330 Reference Guide...
Page 334: Virtual-Fw-Service Hc-Ip
Identification number for the virtual firewall service, an integer from 1 to 1024. bridging-fw Add this parameter to configure a bridging firewall type. If this parameter is not included in the command, a routing firewall type is configured. Example: Router-N(configure)# id 1 bridging-fw Avaya P330 Reference Guide...
Page 335: Virtual-Fw-Service Ip Route
MinMiss distributes sessions to servers in the same way as Hash. However, MinMiss sustains persistency even when a server is removed or added to the server group. For more information on server metrics, see Load Balancing Metrics on page 198. Example: Router-N(configure)# metric hash Avaya P330 Reference Guide...
Page 336: Virtual-Fw-Service Partner-Mgmnt-Ip
Use the no form of this command to set the persistency time for the virtual firewall service to the default (3600 seconds). Syntax [no] persistency time <time> time The time in seconds, an integer. Avaya P330 Reference Guide...
Page 337: Virtual-Fw-Service Persistency Wildcard
The syntax for this command is: [no] rsg <rsg> The name of the real server group, either a string of up to 32 characters (the rsg-name), or an integer from 1 to 1024 (the rsg-id). Example: Router-N(configure)# rsg rsg1 Avaya P330 Reference Guide...
Page 338: Virtual-Fw-Service Simulate-Hash
Use the simulate-hash command to predict which Real Server is selected based on packet IP address. The syntax for this command is: simulate-hash <src-IP> <dest-IP> src-IP The source IP address. dest-IP The destination IP address. Example: Router-N(configure)# simulate-hash 193.170.1.1 10.1.1.1 Avaya P330 Reference Guide...
Page 339: Virtual Server Commands
Use the show virtual-server details command to display the full details of all virtual servers. The syntax for this command is: show virtual-server details [<server name>] server name The name of the virtual server, a string up to 80 characters. Example: Router-N> show virtual-server details Avaya P330 Reference Guide...
Page 340: Virtual-Server
User level: privileged, supervisor Use the id command to set the identification number for the virtual server. The syntax for this command is: id <server-id> server-id Identification number for the virtual server, an integer from 1 to 1024. Avaya P330 Reference Guide...
Page 341: Virtual-Server Vip
IP address of the virtual server. The syntax for this command is: [no] vip <IP-address> IP-address The IP address of the virtual server. Example: Router-N(configure)# vip 192.46.10.44 Avaya P330 Reference Guide...
Page 342: Virtual Server Virtual Slb Service Commands
[<server name> [<service name>]] server name The name of the virtual SLB server, a string up to 80 characters. service name The name of the virtual SLB service, a string up to 32 characters. Avaya P330 Reference Guide...
Page 343: Virtual-Server Virtual-Slb-Service
Use the admin-status command to set the administrative status to enable or disable. The syntax for this command is: admin-status <enable | disable> enable Set admin status to enable. disable Set admin status to disable. Example: Router-N(configure)# admin-status enable Avaya P330 Reference Guide...
Page 344: Virtual-Server Virtual-Slb-Service Application
The hash key is based on the source IP address. The hash key is based on the destination IP address. src-dst The hash key is based on the source and destination IP addresses. Example: Router-N(configure)# hash-key src Avaya P330 Reference Guide...
Page 345: Virtual-Server Virtual-Slb-Service Hc
Use the id command to set the identification number for the virtual SLB service. The syntax for this command is: id <service-id> service-id Identification number for the virtual SLB service, an integer from 1 to 1024. Example: Router-N(configure)# id 21 Avaya P330 Reference Guide...
Page 346: Virtual-Server Virtual-Slb-Service Metric
Use the persistency command to enable persistency for the virtual SLB service. Use the no form of this command to disable persistency for the virtual SLB service (the default). The syntax for this command is: [no] persistency Example: Router-N(configure)# persistency Avaya P330 Reference Guide...
Page 347: Virtual-Server Virtual-Slb-Service Persistency Time
SLB service to the default (0.0.0.0). The syntax for this command is: [no] persistency wildcard <wildcard> wildcard The client IP network wildcard. Example: Router-N(configure)# persistency wildcard 0.0.15.255 Avaya P330 Reference Guide...
Page 348: Virtual-Server Virtual-Slb-Service Pip-Bank
SLB service to the default (0). Syntax [no] real-port <min-r-port> min-r-port Minimum real port number, from 0 to 65535. Example: Router-N(configure)# real-port 12 Avaya P330 Reference Guide...
Page 349: Virtual-Server Virtual-Slb-Service Rsg
Use the simulate-hash command to predict which Real Server is selected based on packet IP address. The syntax for this command is:S service simulate-hash <src-IP> src-IP The source IP address of the device. Example: RLB_3-1(config-v-slb-srvc:aaa:aaa)# simulate-hash 193.170.1.1 Avaya P330 Reference Guide...
Page 350: Vlan Area Commands
User level: user, privileged, supervisor Use the show vlan-area-mapping command to display all vlan-area mappings. The syntax for this command is: show vlan-area-mapping [<vlanID>] vlanID The vlan identification number, an integer from 1 to 4094. Example: Router-N> show vlan-area-mapping 1 Avaya P330 Reference Guide...
Page 351: Index Of Layer 2 Cli Commands
44 ip access-list 26 set device-mode 44 ip access-list-cookie 27 set dot1x max-req 45 ip access-list-copy 28 set dot1x quiet-period 45 ip access-default-action 28 set dot1x re-authperiod 46 ip access-list-dscp operation 29 set dot1x server-timeout 46 Avaya P330 Reference Guide...
Page 352 66 set snmp community 91 set port duplex 66 set snmp retries 91 set port edge admin state 67 set snmp timeout 91 show port edge state 68 set snmp trap 92 Avaya P330 Reference Guide...
Page 353 111 show security mode 147 show ip access-list-dscp 112 show self-loop-discovery 147 show ip access lists 113 show snmp 149 show ip access-list-summary 114 show snmp retries 150 show ip route 114 show snmp timeout 150 Avaya P330 Reference Guide...
Page 354 155 show time parameters 155 show timeout 156 show timezone 156 show trunk 157 show username 157 show vlan 158 show web aux-files-url 159 stack health 159 sync time 159 tech 160 username 160 validate-group 161 Avaya P330 Reference Guide...
Page 355: Index Of Layer 3 Cli Commands
238 ip rip split-horizon 239 icmp in-echo-limit 174 ip route 183 interface 227 ip routing 184 ip access list 175 ip routing-mode 240 ip access-default-action 174 ip simulate 185 ip access-list-cookie 176 ip srrp backup 240 Avaya P330 Reference Guide...
Page 356 Shortcuts to Commands by Context 163 show tftp upload status 225 show access-group 195 show vlan 225 show copy status 195 show device-mode 196 tech 225 show dscp 197 timeout 252 show erase status 197 timers basic 248 Avaya P330 Reference Guide...
Page 357 Index of Layer 3 CLI Commands timers spf 251 traceroute 226 Avaya P330 Reference Guide...
Page 358 Index of Layer 3 CLI Commands Avaya P330 Reference Guide...
Page 359: Index Of Load-Balancing Commands
275 rsg real-routing-fw 295 real-ar-server hc failure-retries 275 rsg real-slb-server 296 real-ar-server hc interval 275 real-ar-server hc success-retries 276 set vlan-area 326 real-ar-server hc timeout 276 show ar-filter 255 real-ar-server weight 277 show ar-filter details 256 Avaya P330 Reference Guide...
Page 360 308 wildcard 323 virtual-ar-service admin-status 301 virtual-server virtual-slb-service pip-bank 324 virtual-ar-service application 301 virtual-server virtual-slb-service real-port 324 virtual-ar-service failure-action 302 virtual-server virtual-slb-service rsg 325 virtual-ar-service hash-key 303 virtual-slb-service simulate-hash 325 virtual-ar-service hc 303 Avaya P330 Reference Guide...

Avaya P330 Reference Manual

Chapter 1 Using the CLI

Chapter 2 Avaya P330 Layer 2 CLI Commands

Chapter 3 Avaya P330 Layer 3 CLI Commands

Quick Links

Related Manuals for Avaya P330

Summary of Contents for Avaya P330