Avaya P333T-PWR Quick Start For Hardware Installation
  1. Manuals
  2. Brands
  3. Avaya Manuals
  4. Switch
  5. P333T-PWR
  6. Quick start for hardware installation

Avaya P333T-PWR Quick Start For Hardware Installation

Avaya stackable switch quick start guide
Hide thumbs Also See for P333T-PWR:
Table of Contents

Advertisement

Quick Links

Download this manual
Quick Start for Hardware
Installation
Avaya P333T-PWR Stackable Switch
10-300732
Issue 1
September 2005

Advertisement

Table of Contents
loading

Related Manuals for Avaya P333T-PWR

Summary of Contents for Avaya P333T-PWR

  • Page 1 Quick Start for Hardware Installation Avaya P333T-PWR Stackable Switch 10-300732 Issue 1 September 2005...

  • Page 3: Table Of Contents

    Chapter 3: Mount the Device ....... Before you Install the P333T-PWR in a Rack....
  • Page 4 Documentation........Quick Start for Hardware Installation: P333T-PWR Stackable Switch...
  • Page 5 Quick Start for Hardware Installation: P333T-PWR Stackable Switch September 2005...
  • Page 6 Copyright 2005, Avaya Inc. All Rights Reserved Notice Every effort was made to ensure that the information in this document was complete and accurate at the time of printing. However, information is subject to change. Warranty Avaya Inc. provides a limited warranty on this product. Refer to your sales agreement to establish the terms of the limited warranty.

  • Page 7: Chapter 1: Before You Start

    Chapter 1: Before you Start Before you install your Avaya Switch, prepare all the information, resources, and tools that you need during the installation process. Good preparation ensures a smooth installation with the least amount of interruption. WARNING: ONLY TRAINED AND QUALIFIED PERSONNEL SHOULD BE ALLOWED TO WARNING: INSTALL OR REPLACE THIS EQUIPMENT.

  • Page 8: Preparing Installation Files

    Table 1: Mounting Tools If you need to mount on... Rack Choosing the Installation Site Ensure that the location where you install your P333T-PWR fulfills the following requirements: Cables are away from sources of electrical noise such as: ● radio transmitters ●...
  • Page 9 Table 3: Power Requirements Power consumption AC Input voltage AC Input current DC Input voltage DC Input current See the Avaya P333T-PWR User’s Guide for additional information on environmental requirements. Choosing the Installation Site Acceptable values to 122 F (-5...

  • Page 10: Building A Stack

    It is highly recommended to upgrade/downgrade before connecting the added Tip: box to an existing stack. - Ensure switches of the same type have the same firmware version 8 Quick Start for Hardware Installation: P333T-PWR Stackable Switch to see which firmware versions can be used in mixed stacks.
  • Page 11 Table 4: Firmware Versions Matrix Required version Stack without C360 Switch 3.11 P333T 3.11.0 P334T 3.11.0 P333R 3.11.0 P333R-LB 3.11.0 P332MF 3.11.0 P333T-PWR 3.11.0 G700 3.11.0 P334T-ML 3.11.16 P332G-ML 3.11.15 P332GT-ML 3.11.15 C363T C364T C363T-PWR C364T-PWR Note: Position the C360 switches either at the top or bottom of the stack to ensure Note: mechanical stability.

  • Page 12: Stack Master Election Rules

    P332GT-ML P332G-ML P334T-ML G700 P333R, P333R-LB P333T, P334T, P332MF P333T-PWR P333R, P333R-LB P333R-LB 10 Quick Start for Hardware Installation: P333T-PWR Stackable Switch Switch mode Stack Master election priority Layer 2 Layer 2 Layer 3 Layer 3 Layer 2 Layer 2...
  • Page 13 Figure 1: Example stack elections C364T-PWR Layer 3 C363T-PWR Layer 2 P334T-ML Layer 3 P333T G700 Figure notes: 1. Stack Master Stack Master election rules P363T-PWR Layer 2 P333T G700 P334T-ML Layer 3 C363T-PWR Layer 2 Issue 1 September 2005...
  • Page 14 Before you Start 12 Quick Start for Hardware Installation: P333T-PWR Stackable Switch...

  • Page 15: Chapter 2: Unpack The Device

    ELECTROSTATIC ALERT: P333T-PWR Connect the strap to an approved ground, such as an unpainted metal surface. Equipment Open the box that contains the P333T-PWR and ensure that it contains the following components and accessories: One Avaya P333T-PWR Switch. ● One Accessory Kit that contains: ●...

  • Page 16: Documentation

    Adapter One DB25M Adapter Four (4) 5/16" Round Head Screws Four (4) Washers Four (4) stand-off feet Documentation Avaya P333T-PWR Quick Start Guide (this document) ● Avaya P333T-PWR Release Notes ● 14 Quick Start for Hardware Installation: P333T-PWR Stackable Switch...

  • Page 17: Avaya P330 Documentation And Utilities Cd

    Avaya P330 Documentation and Utilities CD (see detail below) ● Avaya Communication Warranty and License Agreement ● Avaya P330 Documentation and Utilities CD The CD contains the latest User's Guides for the Avaya P330 stackable switches and files for use with the Embedded Web Manager. User's Guides ●...
  • Page 18 Unpack the Device 16 Quick Start for Hardware Installation: P333T-PWR Stackable Switch...

  • Page 19: Chapter 3: Mount The Device

    Chapter 3: Mount the Device You can mount the P333T-PWR in a rack. The P333T-PWR chassis fits in most standard 19-inch racks. It is 2U (3.5”, 88 mm) high. Before you Install the P333T-PWR in a Rack Disconnect all cables from the unit before proceeding with the rack installation.
  • Page 20 3. Secure the unit to the rack, taking care not to overtighten the screws. 4. Snap closed the hinged ends of the front panel. Tip: You can now safely connect the cables to the unit. Tip: 18 Quick Start for Hardware Installation: P333T-PWR Stackable Switch 11 12 ROUT Hspd OPR PWR...

  • Page 21: Chapter 4: Power Up

    Chapter 4: Power Up Connecting the P333T-PWR to the main electrical supply provides power to the switch. VOLTAGE ALERT: To isolate the switch completely, you must disconnect all power connections: AC VOLTAGE ALERT: plug or DC terminal block and DC BUPS power.

  • Page 22: Dc Input (Optional)

    Figure 5: P333R DC version rear panel Figure notes: 1. DC input terminal block The P333T-PWR an operate on the AC input only. However, you may wish to use the optional DC input for the following: Backup for the Power over Ethernet ports ●...

  • Page 23: Chapter 5: Prepare For Configuration

    This section describes the procedure for establishing switch access between a terminal and the Avaya P333T-PWR switch over the serial port provided on the front panel of the P333T-PWR (RJ-45 connector labeled “Console”). For information on the console port pin assignments, refer to the Avaya P333T-PWR User Guide.

  • Page 24: Assigning A Stack Ip Address

    Assigning a Stack IP Address Note: All P333T-PWR switches are shipped with the same default IP address. You must Note: change the IP address of the master switch in a stack in order to guarantee that the stack has its own unique IP address in the network.

  • Page 25: Establishing A Telnet Connection

    Stack or Router parameters. You can Telnet the Stack Master IP address: 1. Connect your station to the network. 2. Verify that you can communicate with the Avaya P333T-PWR by pinging the IP of the Avaya P333T-PWR. If there is no response using ping, check the IP address and default gateway of both the Avaya P333T-PWR and the station.

  • Page 26: Basic Configuration

    <vlan>, <ip_address> and <netmask> with the VLAN, IP address and net mask of the stack and press Enter. 2. At the P333T-PWR(super)# prompt, type reset and press Enter to reset the stack. 3. After the reset, perform login again as described above.
  • Page 27 For further information, please refer to Chapter 6 of the Avaya P333T-PWR User’s Guide. The default settings for the Avaya P333T-PWR switch and its ports are determined by the Avaya P333T-PWR firmware. These default settings are subject to change in newer versions of the Avaya P333T-PWR firmware.
  • Page 28 Port priority Inline power Inline power priority Tip: Functions operate in their default settings unless configured otherwise. Tip: 26 Quick Start for Hardware Installation: P333T-PWR Stackable Switch Default Setting 10/100-TX ports: Auto-negotiation ● 100Base-FXports:100 Mbps full duplex ● 1000Base-X ports: 1000 Mbps full duplex ●...

  • Page 29: Chapter 6: Device Manager

    ● Port Redundancy - Setting port redundancy for ports in a P333T-PWR Switch. ● Port Mirroring - Setting up port mirroring for ports in a P333T-PWR Switch. ● Trap Managers Configuration - Viewing and modifying the Trap Managers Table. ●...

  • Page 30: Configuring The Device Manager

    Note: You should assign an inband or out-of-band interface IP address to the switch Note: before beginning this procedure. 28 Quick Start for Hardware Installation: P333T-PWR Stackable Switch Use the following command... set snmp retries set snmp time-out set web aux-files-url...
  • Page 31 To run the Device Manager: 1. Open your browser. 2. Enter the URL of the switch in the format http://aaa.bbb.ccc.ddd where aaa.bbb.ccc.ddd is the inband or outband interface IP address of the switch. - The user name is “root”. - The default password for read-only access is “root”. - The default passwords for read-write access is “root”.

  • Page 32: Installing The Java Plug-In

    To install from the P330 Documentation and Utilities CD: 1. Close all unnecessary applications on your PC. 2. Insert the Avaya P330 Documentation and Utilities CD in the CD drive. 3. Open Windows Explorer. 30 Quick Start for Hardware Installation: P333T-PWR Stackable Switch Installing the Java Plug-in).

  • Page 33: Install From The Avaya Web Site

    Utilities” CD to your local Web server. Refer to your Web server documentation for full instructions. 2. Define the URL in the P333T-PWR using the following CLI command: set web aux-files-url //IP address/directory name where //IP address/directory name is the location of the directory from the previous step.

  • Page 34: Documentation

    Device Manager Documentation The Device Manager comes with a detailed User’s Guide including a Glossary of Terms and an overview of Data Communications concepts. 32 Quick Start for Hardware Installation: P333T-PWR Stackable Switch...

Table of Contents