Cabletron Systems SmartSwitch 6000 User Manual page 414

Clearing causes.......................................................... D-2
async................................................................... C-6
Collecting Node.......................................................... 3-7
Collecting Node ID .................................................... 3-6
Collecting Node Pwd (password)............................... 3-6
Com. Port Parity ......................................................... 3-7
Com. Port Stopbit ....................................................... 3-7
Com. Port Thruput...................................................... 3-7
Command mode (async terminal) ............................. C-1
Committed Burst Size .............................................. 6-34
Committed Burst Size (In/Out) ................................ 6-18
Committed Information Rate ................................... 6-34
Committed Information Rate (In/Out) ..................... 6-18
Community Table, configuring ................................ 14-4
Configuration database............................................... 2-1
Configuration report ................................................... 2-3
Connection ID ............................................................ 9-8
Connection Priority 6-24, 6-31, 6-33, 7-16, 7-24, 10-20,
............................................. 11-6, 11-11, 12-12
Connections, displaying ........................................... 17-5
Controller Type ........................................................ 9-13
Copying a database record ....................................... 1-18
after........................................................................... 10-5
CSU/DSU Operating Mode............................... 6-17, 7-6
CSU/DSU tests ....................................................... 16-17
D
Data Forwarding Char .............................................. 10-4
Data Mode .................................................................. 9-8
Data transfer mode (async terminal) ......................... C-1
Database ..................................................................... 2-1
backing up
Frame Relay Module ............................... 16-13
FRX4000 .................................................. 16-11
FRX6000 .................................................. 16-12
files .................................................................... 16-7
restoring
Frame Relay Module ............................... 16-13
FRX4000 .................................................. 16-11
FRX6000 .................................................. 16-12
setup recommendations....................................... 2-2
Database and system memory values......................... 5-4
Database Display ........... 6-25, 7-7, 8-8, 9-6, 9-13, 10-12
Database Display (Y/N) ............................................. 5-4
Date, changing ............................................................ 3-3
Default Calling Address ........................ 6-27, 7-8, 10-12
Default Ethernet Frame Type................................... 13-5
Default Packet Size ........................................... 6-26, 7-8
Default Window Size ........................................ 6-27, 7-8
Delay Retry Count .................................................... 9-14
Delay Timer.............................................................. 9-14
Delete (BSC subscriber).................................... 9-3, 9-15
Delete CUG .............................................................. 6-28
Index-2
Deleting a database record ........................................ 1-17
Destination IP Address ............................................. 11-6
Destination MAC Address Value ............................. 13-8
Destination Mask ...................................................... 11-9
Destination NetBIOS Name ..................................... 13-9
Destination Network Value ...................................... 12-7
Destination Node Value............................................ 12-7
Destination Socket Value ......................................... 12-7
Destination Subscriber.................................. 11-7, 12-15
Diagnostic codes........................................................ D-4
FRX/FRM-specific ............................................. D-6
SNA.................................................................... D-5
X.25 .................................................................... D-4
Dial port, configuring ............................................... 7-12
Dial Support .............................................................. 7-12
Disable Request Disconnect ....................................... 8-8
Disable Status Response........................................... 9-21
Disable X.121 User Calls ....................................... 10-12
Discard Output .......................................................... 10-5
Disconnect Duration ............................................... 10-13
Disconnect if Clear Recvd ...................................... 10-14
Disconnect if Clear Sent ......................................... 10-14
Disconnect Timer ......................................... 7-13, 10-13
Display All CUGs..................................................... 6-28
DLCI configuration, reviewing ................................ 6-10
DLCI parameters, configuring .................................. 6-11
DLCI sharing .............................................................. 6-1
DLCIs, learned .......................................................... 6-13
DSAP Value ............................................................. 13-9
DSU/CSU tests ....................................................... 16-17
DTE Clear Retry Count .................................... 6-27, 7-9
DTE Reset Retry Count .................................... 6-27, 7-9
DTE Restart Retry Count ................................. 6-27, 7-9
DTR/RTS Active When VC Up ............................. 10-13
E
EBCDIC............................................................ 9-6, 9-13
Echo .......................................................................... 10-4
Echo Mask ................................................................ 10-6
Edit Service Signal ................................................... 10-6
Editing (in async PAD profile)................................. 10-5
Enable Backup Protocol?.......................................... 6-19
Enable Bandwidth Allocation................................... 6-18
Enable Outgoing Rate Control ................................. 6-18
Enabled (traps).......................................................... 14-7
Encapsulation Method .............................................. 6-24
End-to-End Acknowledgment .................................... 9-7
Entry ......................................................................... 6-35
ERRMSG.TXT......................................................... 18-1
Errmsg.txt Database Error ........................................ 3-12
Error codes from async terminal ............................... C-6
Error Retransmit Count .............................................. 9-8
Escape key ................................................................ 1-18
FRX/FRM 3.3 User Guide, Rev 04