Cabletron Systems MMAC-Plus 9T101-04 User Manual

Four port token ring router
Hide thumbs Also See for MMAC-Plus 9T101-04:

Advertisement

Quick Links

MMAC-Plus
9T101-04
Four Port Token Ring Router
User's Guide

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MMAC-Plus 9T101-04 and is the answer not in the manual?

Questions and answers

Summary of Contents for Cabletron Systems MMAC-Plus 9T101-04

  • Page 1 ™ MMAC-Plus 9T101-04 Four Port Token Ring Router User’s Guide...
  • Page 3 Notice Notice Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes have been made.
  • Page 4: Fcc Notice

    Notice FCC Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules.
  • Page 5: Doc Notice

    Notice DOC Notice This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique édicté...
  • Page 6 Notice...
  • Page 7: Table Of Contents

    Chapter 1 Introduction Features... 1-1 Related Manuals... 1-4 Getting Help ... 1-4 Chapter 2 Installing the MMAC-Plus Module The Reset Switch ... 2-3 Local Management Console ... 2-3 Chapter 3 Operation Flexible Network Bus (FNB)... 3-2 System Management Buses ... 3-2 System Diagnostic Controller...
  • Page 8 Contents...
  • Page 9: Chapter 1 Introduction

    Introduction The 9T101-04 Token Ring Router module, shown in Figure 1-1, is a four port Token Ring router. Up to four front panel network connections can be made to this module and they can be routed to any other port and to any other MMAC-Plus module via the FNB bus.
  • Page 10 With LANVIEW LEDs, you can quickly identify the device, port, and physical layer status at a glance. Hot Swapping The 9T101-04 can be installed or removed from the chassis while the MMAC-Plus is powered up without affecting the operation of the remaining modules in the chassis.
  • Page 11 FDDI 9T101-04 IN-RING A 1 6 M b IN-RING B 1 6 M b IN-RING A 1 6 M B IN-RING B 1 6 M b MMAC PLUS Figure 1-1. The 9T101-04 Module Features...
  • Page 12: Related Manuals

    Cisco Systems R4500 manuals - CRM-DOC or CRM-CDROM Getting Help If you need additional support with the MMAC-Plus, or if you have any questions, comments or suggestions concerning this manual, feel free to contact Cabletron Systems Technical Support: By phone: By CompuServe By Internet mail:...
  • Page 13: Chapter 2 Installing The Mmac-Plus Module

    Remove the module from the plastic bag. Observe all precautions to prevent damage from Electrostatic Discharge (ESD). Carefully examine the module, checking for damage. If any damage exists, DO NOT install the module. Contact Cabletron Systems Technical Support immediately. Before installing the MMAC-Plus cards into the chassis, ensure that the bottom and top plastic tabs are unlocked.
  • Page 14 Installing the MMAC-Plus Module Metal Back-Panel FLNK FLNK FLNK FLNK FLNK Circuit Card Card Guides Warning: Ensure that the circuit card is between the card guides. Lock down the top and bottom plastic tabs at the same time, applying even pressure. Figure 2-1.
  • Page 15: The Reset Switch

    Local Management Console Local Management is accessed by attaching a management console at the RJ-45 CON port of the 9T101-04. The console connection supports a Digital Equipment Corporation VT 320™ terminal or PC emulation of one of these terminals. Table 2-1 lists the setup requirements for the local management console. If your terminal is a Digital Equipment Corporation VT 320™...
  • Page 16 Installing the MMAC-Plus Module Table 2-1. Terminal Setup Requirements Menu Display Setup: General Setup: Communications Setup: Keyboard Setup: Function Selection Columns 80 Columns Controls Interpret Controls Auto Wrap No Auto Wrap Text Cursor Cursor Mode 7 Bit Control Cursor Keys Normal Cursor Keys Transmit...
  • Page 17 Figure 2-3. Console Cable Pinouts Connect the console to the module as follows: Attach the male RJ-45 connector to the CON port of the 9T101-04. Attach the female end (25-pin or 9-pin, as applicable) to the terminal. Refer to the Cisco Systems documentation for information on configuring this module.
  • Page 18 Installing the MMAC-Plus Module...
  • Page 19: Chapter 3 Operation

    Operation The 9T101-04 Token Ring Router module is a four port router. Four front panel network connections can be made to this module and they can be routed to any other port and to any other MMAC-Plus module via the FNB bus.
  • Page 20: Flexible Network Bus (Fnb)

    LCD located on the Environmental Module. The 9T101-04 have been designed so that in the event of a diagnostic controller fault, the modules will continue to function.
  • Page 21: Fnb Interface

    FNB-1 or FNB-2; the second allows dual attachment to both FNB-1 and FNB-2. The 9T101-04 has one dual attachment to the FNB backplane, connecting to either FNB-1 or FNB-2. The module can insert into the FNB or bypass it.
  • Page 22 Operation...
  • Page 23: Chapter 4 Lanview Leds

    LANVIEW LEDs The front panel LANVIEW LEDs, shown in Figure 4-1, indicate the status of the module and may be used as an aid in troubleshooting. 9T101-04 Token Ring Insertion IN-RING A IN-RING B IN-RING A IN-RING B Figure 4-1. LANVIEW LEDs...
  • Page 24 LANVIEW LEDs The functions of the System Management Bus (SMB) and CPU LEDs are listed in Table 4-1. LED Color Green Yellow (Flashing) Yellow Red (Flashing) * At least one Token Ring port in both groups 0-1 and 2-3 are down. The function of the FNB Receive LED is listed in Table 4-2.
  • Page 25 The functions of the Token Ring Insertion LEDs are listed in Table 4-4. Table 4-4. Token Ring Insertion LEDs LED Color Green Inserted into ring Not Inserted The function of the Ring Speed LEDs are listed in Table 4-5. Table 4-5. Ring Speed LEDs LED Color Green 16 mbps...
  • Page 26 LANVIEW LEDs...
  • Page 27: Chapter 5 Specifications

    Specifications Safety It is the responsibility of the person who sells the system to which the module will be a part to ensure that the total system meets allowed limits of conducted and radiated emissions. CAUTION This equipment meets the following safety requirements: •...
  • Page 28: Physical

    Specifications Physical Dimensions 35.0 D x 44.0 H x 3.0 W centimeters (13.8 D x 17.4 H x 1.2 W inches) Weight Unit: Shipping: Environment Operating Temperature Storage Temperature Relative Humidity 1.36 kg. (3 lb) 1.81 kg. (4 lb) 5 to 40 C -30 to 90 C 5% to 95% non-condensing...

Table of Contents

Save PDF