INVT Goodrive 35 Series Operation Manual page 213

inverters
Goodrive35
S1
S2
S3
S4
S5
S6
S7
P05.00
S8
0
1
HD1
0 No function
4 Forward jogging
8 Running pause
Frequency increasing/decreasing setting
12
clear
16 Multi-stage speed terminal 1
20 Multi-stage speed pause
23 Simple PLC pause
28 Counter reset
32 Length reset
36 Shift the command to the keypad
40 Power consumption clear
This parameter is used to set the function corresponds to the digital multi-function terminals.
Note: two different multi-function terminals can not be set as one function.
Set
value
0 No function
1 Forward running(FWD)
2 Reverse running(REV)
3 3-wire running control
4 Forward jogging
5 Reverse jogging
6 Coast to stop
P05.10
P05.11
P05.14
0
T delay
1 -1
0 P05.16
T delay
1 -1
P05.18
0
T delay
1 -1
0 P05.20
T delay
1 -1
P05.22
0
T delay
1 -1
P05.24
0
T delay
1 -1
P05.26
0
T delay
1 -1
P05.28
0
T delay
1 -1
P05.30
0
T delay
1 -1
1 Forward running
5 Reverse jogging
9 External fault input 10
Shifting between A frequency and B
13 14
frequency
17 Multi-stage speed terminal 2 18
21 ACC/DEC time selection 1 22
25 PID control pause 26
29 Torque control disabling 30
Frequency increasing/decreasing setting
33
clear
37 Shift the command to the terminal 38
41 Power consumption keeping 42~63
Function
The inverter does not work even there is input signal.
It is necessary to set the terminal which can not be
used to non-function to avoid misacting.
The forward or reverse rotation of the inverter can be
controlled by the external terminals.
The terminal can determine the running mode of the
inverter is 3-wire control mode. Refer to P05.13 for
detailed instruction of 3-wire control mode.
See P08.06, P08.07 and P08.08 for jogging
frequency, jogging ACC/DEC time.
The inverter closes off the output. The motor is not
controlled by the inverter during the stopping. This
method is usually to be used when the load inertia is
big and it has no requirement to the stopping time.
It has the same meaning with the "coast to stop" in
P01.08 and usually used in remote control.
www.barghmaher.ir
Switch function selection
P05.15
T delay P05.01
(default value is 1)
P05.17
T delay P05.02
(default value is 4)
P05.19
T delay P05.03
(default value is 7)
P05.21
T delay P05.04
(default value is 0)
P05.23
T delay P05.05
(default value is 0)
P05.25
T delay P05.06
(default value is 0)
P05.27
T delay P05.07
(default value is 0)
P05.29
T delay P05.08
(default value is 0)
P05.31
T delay P05.09
(default value is 0)
3 3-wire running control
2 Reverse running
7 Fault reset
6 Coast to stop
Frequency setting increasing (UP) 11 Frequency setting decreasing (DOWN)
Shifting between the combination setting Shifting between the combination setting
15
and A frequency and B frequency
19 Multi-stage speed terminal 4
Multi-stage speed terminal 3
ACC/DEC time selection 2 23 Simple PLC stopping reset
Traverse pause (stop at the current Traverse reset (stop at the middle
27
frequency) frequency)
31 Counter trigging
ACC/DEC disabling
34 DC braking 35 Shift from motor 1 to motor 2
39 Pre-exciting command
Shift the command to the communication
Reserved
Instructions
212
Basic operation instruction
0
Running
P17.11
1
Switch input terminal
state
2
Fault?
3
Fault P07.37
The current fault
switch input terminal
state
4
5
.
P05.10 P17.11 P07.37 display
S1 BIT0 S2 BIT1
.
S3 BIT2 S4 BIT3
S5 BIT4 S6 BIT5
.
S7 BIT6 S8 BIT7
HDI BIT8
.
0: HDI is high speed pulse input
P05.00
1: HDI is switch input
29
30